/dev/sda === START OF INFORMATION SECTION === Device Model: KingDian S200 60GB Serial Number: -- LU WWN Device Id: 0 000000 ... Firmware Version: P0921B User Capacity: 60 022 480 896 bytes [60,0 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.1, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Thu Dec 14 01:04:55 2017 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Disabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 1) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate ------ 100 100 050 - 0 5 Reallocated_Sector_Ct -O---- 100 100 050 - 0 9 Power_On_Hours ------ 100 100 050 - 4 12 Power_Cycle_Count ------ 100 100 050 - 62 160 Unknown_Attribute ------ 100 100 050 - 0 161 Unknown_Attribute ------ 100 100 050 - 265 162 Unknown_Attribute ------ 100 100 050 - 0 163 Unknown_Attribute ------ 100 100 050 - 30 164 Unknown_Attribute ------ 100 100 050 - 9831 165 Unknown_Attribute ------ 100 100 050 - 5 166 Unknown_Attribute ------ 100 100 050 - 3 167 Unknown_Attribute ------ 100 100 050 - 4 168 Unknown_Attribute ------ 100 100 050 - 3000 169 Unknown_Attribute ------ 100 100 050 - 100 192 Power-Off_Retract_Count ------ 100 100 050 - 31 194 Temperature_Celsius ------ 100 100 050 - 49 195 Hardware_ECC_Recovered ------ 100 100 050 - 100 196 Reallocated_Event_Count ------ 100 100 050 - 0 199 UDMA_CRC_Error_Count ------ 100 100 050 - 0 241 Total_LBAs_Written ------ 100 100 050 - 8917 242 Total_LBAs_Read ------ 100 100 050 - 6124 245 Unknown_Attribute ------ 100 100 050 - 9404 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 62 --- Lifetime Power-On Resets 0x01 0x010 4 4 --- Power-on Hours 0x01 0x018 6 584392181 --- Logical Sectors Written 0x01 0x020 6 2376040 --- Number of Write Commands 0x01 0x028 6 401390165 --- Logical Sectors Read 0x01 0x030 6 5049861 --- Number of Read Commands 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 49 --- Current Temperature 0x05 0x010 1 91 --- Average Short Term Temperature 0x05 0x018 1 -126 --- Average Long Term Temperature 0x05 0x020 1 49 --- Highest Temperature 0x05 0x028 1 49 --- Lowest Temperature 0x05 0x030 1 91 --- Highest Average Short Term Temperature 0x05 0x038 1 39 --- Lowest Average Short Term Temperature 0x05 0x040 1 -1 --- Highest Average Long Term Temperature 0x05 0x048 1 3 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 100 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 219 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.9 Device Model: ST3200827AS Serial Number: -- Firmware Version: 3.AAH User Capacity: 200 049 647 616 bytes [200 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Thu Dec 14 01:04:55 2017 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 70) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 114 087 006 - 76753713 3 Spin_Up_Time PO---- 091 090 000 - 0 4 Start_Stop_Count -O--CK 096 096 020 - 4456 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 081 060 030 - 159124303 9 Power_On_Hours -O--CK 097 097 000 - 3294 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 4641 187 Reported_Uncorrect -O--CK 001 001 000 - 111 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 060 036 045 Past 40 (Min/Max 32/40) 194 Temperature_Celsius -O---K 040 064 000 - 40 (0 10 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 073 051 000 - 150195551 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 14 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 SATA NCQ Queued Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 396 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 396 [15] occurred at disk power-on lifetime: 1225 hours (51 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 d2 02 61 02 e0 00 Error: UNC at LBA = 0xd2026102 = 3523371266 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 01 00 00 d2 00 61 02 e0 00 00:01:39.046 READ DMA EXT 25 00 03 00 01 00 00 d2 00 61 01 e0 00 00:01:39.046 READ DMA EXT 25 00 03 00 01 00 00 d2 00 61 00 e0 00 00:01:39.046 READ DMA EXT 25 00 03 00 01 00 00 d1 00 61 ff e0 00 00:01:39.046 READ DMA EXT 25 00 03 00 01 00 00 3b 00 63 b6 e0 00 00:01:39.046 READ DMA EXT Error 395 [14] occurred at disk power-on lifetime: 1225 hours (51 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 d2 02 61 02 e0 00 Error: UNC at LBA = 0xd2026102 = 3523371266 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 01 00 00 d2 00 61 02 e0 00 00:13:16.285 READ DMA EXT 25 00 03 00 01 00 00 d2 00 61 01 e0 00 00:13:16.284 READ DMA EXT 25 00 03 00 01 00 00 d2 00 61 00 e0 00 00:13:16.287 READ DMA EXT 25 00 03 00 01 00 00 d1 00 61 ff e0 00 00:13:16.287 READ DMA EXT 25 00 03 00 01 00 00 9f 00 62 d6 e0 00 00:13:16.287 READ DMA EXT Error 394 [13] occurred at disk power-on lifetime: 1225 hours (51 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 d2 02 61 02 e0 00 Error: UNC at LBA = 0xd2026102 = 3523371266 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 01 00 00 d2 00 61 02 e0 00 00:07:32.618 READ DMA EXT 25 00 03 00 01 00 00 d2 00 61 01 e0 00 00:07:32.618 READ DMA EXT 25 00 03 00 01 00 00 d2 00 61 00 e0 00 00:07:32.617 READ DMA EXT 25 00 03 00 01 00 00 d1 00 61 ff e0 00 00:07:32.617 READ DMA EXT 25 00 03 00 01 00 00 9f 00 62 d6 e0 00 00:07:32.617 READ DMA EXT Error 393 [12] occurred at disk power-on lifetime: 1225 hours (51 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 d2 02 61 02 e0 00 Error: UNC at LBA = 0xd2026102 = 3523371266 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 01 00 00 d2 00 61 02 e0 00 00:03:42.781 READ DMA EXT 25 00 03 00 01 00 00 d2 00 61 01 e0 00 00:03:42.781 READ DMA EXT 25 00 03 00 01 00 00 d2 00 61 00 e0 00 00:03:42.780 READ DMA EXT 25 00 03 00 01 00 00 d1 00 61 ff e0 00 00:03:42.780 READ DMA EXT 25 00 03 00 01 00 00 9f 00 62 be e0 00 00:03:42.780 READ DMA EXT Error 392 [11] occurred at disk power-on lifetime: 1225 hours (51 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 d2 02 61 02 e0 00 Error: UNC at LBA = 0xd2026102 = 3523371266 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 01 00 00 d2 00 61 02 e0 00 00:01:39.046 READ DMA EXT 25 00 03 00 01 00 00 d2 00 61 01 e0 00 00:01:39.046 READ DMA EXT 25 00 03 00 01 00 00 d2 00 61 00 e0 00 00:01:39.046 READ DMA EXT 25 00 03 00 01 00 00 d1 00 61 ff e0 00 00:01:39.046 READ DMA EXT 25 00 03 00 01 00 00 3b 00 63 b6 e0 00 00:01:39.046 READ DMA EXT Error 391 [10] occurred at disk power-on lifetime: 1225 hours (51 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 d2 02 61 02 e0 00 Error: UNC at LBA = 0xd2026102 = 3523371266 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 01 00 00 d2 00 61 02 e0 00 00:13:16.285 READ DMA EXT 25 00 03 00 01 00 00 d2 00 61 01 e0 00 00:13:16.284 READ DMA EXT 25 00 03 00 01 00 00 d2 00 61 00 e0 00 00:13:16.287 READ DMA EXT 25 00 03 00 01 00 00 d1 00 61 ff e0 00 00:13:16.287 READ DMA EXT 25 00 03 00 01 00 00 9f 00 62 d6 e0 00 00:13:16.287 READ DMA EXT Error 390 [9] occurred at disk power-on lifetime: 1225 hours (51 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 d2 02 61 02 e0 00 Error: UNC at LBA = 0xd2026102 = 3523371266 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 01 00 00 d2 00 61 02 e0 00 00:07:32.618 READ DMA EXT 25 00 03 00 01 00 00 d2 00 61 01 e0 00 00:07:32.618 READ DMA EXT 25 00 03 00 01 00 00 d2 00 61 00 e0 00 00:07:32.617 READ DMA EXT 25 00 03 00 01 00 00 d1 00 61 ff e0 00 00:07:32.617 READ DMA EXT 25 00 03 00 01 00 00 9f 00 62 d6 e0 00 00:07:32.617 READ DMA EXT Error 389 [8] occurred at disk power-on lifetime: 1225 hours (51 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 d2 02 61 02 e0 00 Error: UNC at LBA = 0xd2026102 = 3523371266 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 01 00 00 d2 00 61 02 e0 00 00:03:42.781 READ DMA EXT 25 00 03 00 01 00 00 d2 00 61 01 e0 00 00:03:42.781 READ DMA EXT 25 00 03 00 01 00 00 d2 00 61 00 e0 00 00:03:42.780 READ DMA EXT 25 00 03 00 01 00 00 d1 00 61 ff e0 00 00:03:42.780 READ DMA EXT 25 00 03 00 01 00 00 9f 00 62 be e0 00 00:03:42.780 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS