Probe #b7a40ebd24 of AMI Aptio CRB

Log: smartctl

/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.0-37-amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: ST18000NE000-2YY101 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: EN01 User Capacity: 18,000,207,937,536 bytes [18.0 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database 7.3/5319 ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Jul 26 18:58:14 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Disabled ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: scsi error badly formed scsi parameters Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 567) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: (1534) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x50bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 082 064 044 - 174764830 3 Spin_Up_Time PO---- 089 087 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 967 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 090 060 045 - 973176897 9 Power_On_Hours -O--CK 090 090 000 - 9383 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 363 18 Unknown_Attribute PO-R-- 100 100 050 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 099 000 - 2 190 Airflow_Temperature_Cel -O---K 065 048 000 - 35 (Min/Max 34/36) 192 Power-Off_Retract_Count -O--CK 100 100 000 - 49 193 Load_Cycle_Count -O--CK 098 098 000 - 4693 194 Temperature_Celsius -O---K 035 052 000 - 35 (0 21 0 0 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 1 200 Multi_Zone_Error_Rate PO---K 100 100 001 - 0 240 Head_Flying_Hours ------ 100 253 000 - 5884 (17 35 0) 241 Total_LBAs_Written ------ 100 253 000 - 202682335333 242 Total_LBAs_Read ------ 100 253 000 - 15426550628666 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL R/O 256 Device Statistics log 0x04 SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0a GPL R/W 8 Device Statistics Notification 0x0c GPL R/O 2048 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 768 Current Device Internal Status Data log 0x2f GPL - 1 Set Sector Configuration 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 160 Device vendor specific log 0xa2 GPL VS 16320 Device vendor specific log 0xa4 GPL,SL VS 160 Device vendor specific log 0xa6 GPL VS 192 Device vendor specific log 0xa8-0xa9 GPL,SL VS 136 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xad GPL VS 16 Device vendor specific log 0xb1 GPL,SL VS 160 Device vendor specific log 0xb6 GPL VS 1920 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc1 GPL,SL VS 8 Device vendor specific log 0xc3 GPL,SL VS 24 Device vendor specific log 0xc6 GPL VS 5184 Device vendor specific log 0xc7 GPL,SL VS 8 Device vendor specific log 0xc9 GPL,SL VS 8 Device vendor specific log 0xca GPL,SL VS 16 Device vendor specific log 0xcd GPL,SL VS 1 Device vendor specific log 0xce GPL VS 1 Device vendor specific log 0xcf GPL VS 512 Device vendor specific log 0xd1 GPL VS 656 Device vendor specific log 0xd2 GPL VS 10256 Device vendor specific log 0xd4 GPL VS 2048 Device vendor specific log 0xda GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 9342 - # 2 Short offline Completed without error 00% 9029 - # 3 Short offline Completed without error 00% 8861 - # 4 Short offline Completed without error 00% 8693 - # 5 Short offline Completed without error 00% 8525 - # 6 Short offline Completed without error 00% 8357 - # 7 Short offline Completed without error 00% 8189 - # 8 Short offline Completed without error 00% 8029 - # 9 Short offline Completed without error 00% 7886 - #10 Short offline Completed without error 00% 7753 - #11 Short offline Completed without error 00% 7748 - #12 Short offline Completed without error 00% 7430 - #13 Short offline Completed without error 00% 7262 - #14 Short offline Completed without error 00% 7095 - #15 Short offline Completed without error 00% 6927 - #16 Short offline Completed without error 00% 6772 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 34/36 Celsius Lifetime Min/Max Temperature: 20/52 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) Vendor specific: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 4 minutes Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 10/40 Celsius Min/Max Temperature Limit: 5/60 Celsius Temperature History Size (Index): 128 (55) Index Estimated Time Temperature Celsius 56 2025-07-21 13:15 39 ******************** 57 2025-07-21 14:14 40 ********************* 58 2025-07-21 15:13 39 ******************** ... ..( 5 skipped). .. ******************** 64 2025-07-21 21:07 39 ******************** 65 2025-07-21 22:06 42 *********************** 66 2025-07-21 23:05 39 ******************** ... ..( 9 skipped). .. ******************** 76 2025-07-22 08:55 39 ******************** 77 2025-07-22 09:54 ? - 78 2025-07-22 10:53 40 ********************* 79 2025-07-22 11:52 37 ****************** 80 2025-07-22 12:51 ? - 81 2025-07-22 13:50 31 ************ 82 2025-07-22 14:49 ? - 83 2025-07-22 15:48 32 ************* 84 2025-07-22 16:47 35 **************** 85 2025-07-22 17:46 ? - 86 2025-07-22 18:45 24 ***** 87 2025-07-22 19:44 36 ***************** 88 2025-07-22 20:43 ? - 89 2025-07-22 21:42 24 ***** 90 2025-07-22 22:41 37 ****************** 91 2025-07-22 23:40 43 ************************ 92 2025-07-23 00:39 43 ************************ 93 2025-07-23 01:38 44 ************************* 94 2025-07-23 02:37 44 ************************* 95 2025-07-23 03:36 44 ************************* 96 2025-07-23 04:35 43 ************************ 97 2025-07-23 05:34 37 ****************** ... ..( 5 skipped). .. ****************** 103 2025-07-23 11:28 37 ****************** 104 2025-07-23 12:27 40 ********************* 105 2025-07-23 13:26 37 ****************** ... ..( 9 skipped). .. ****************** 115 2025-07-23 23:16 37 ****************** 116 2025-07-24 00:15 41 ********************** 117 2025-07-24 01:14 37 ****************** 118 2025-07-24 02:13 37 ****************** 119 2025-07-24 03:12 37 ****************** 120 2025-07-24 04:11 40 ********************* 121 2025-07-24 05:10 37 ****************** ... ..( 5 skipped). .. ****************** 127 2025-07-24 11:04 37 ****************** 0 2025-07-24 12:03 41 ********************** 1 2025-07-24 13:02 ? - 2 2025-07-24 14:01 34 *************** 3 2025-07-24 15:00 35 **************** 4 2025-07-24 15:59 ? - 5 2025-07-24 16:58 26 ******* 6 2025-07-24 17:57 35 **************** 7 2025-07-24 18:56 36 ***************** 8 2025-07-24 19:55 36 ***************** 9 2025-07-24 20:54 ? - 10 2025-07-24 21:53 40 ********************* 11 2025-07-24 22:52 ? - 12 2025-07-24 23:51 38 ******************* 13 2025-07-25 00:50 ? - 14 2025-07-25 01:49 38 ******************* 15 2025-07-25 02:48 34 *************** 16 2025-07-25 03:47 35 **************** 17 2025-07-25 04:46 ? - 18 2025-07-25 05:45 25 ****** 19 2025-07-25 06:44 ? - 20 2025-07-25 07:43 34 *************** 21 2025-07-25 08:42 ? - 22 2025-07-25 09:41 26 ******* 23 2025-07-25 10:40 ? - 24 2025-07-25 11:39 28 ********* 25 2025-07-25 12:38 ? - 26 2025-07-25 13:37 28 ********* 27 2025-07-25 14:36 35 **************** 28 2025-07-25 15:35 35 **************** 29 2025-07-25 16:34 35 **************** 30 2025-07-25 17:33 ? - 31 2025-07-25 18:32 35 **************** 32 2025-07-25 19:31 ? - 33 2025-07-25 20:30 25 ****** 34 2025-07-25 21:29 34 *************** 35 2025-07-25 22:28 ? - 36 2025-07-25 23:27 35 **************** 37 2025-07-26 00:26 ? - 38 2025-07-26 01:25 35 **************** 39 2025-07-26 02:24 ? - 40 2025-07-26 03:23 35 **************** 41 2025-07-26 04:22 ? - 42 2025-07-26 05:21 35 **************** 43 2025-07-26 06:20 34 *************** 44 2025-07-26 07:19 ? - 45 2025-07-26 08:18 35 **************** 46 2025-07-26 09:17 ? - 47 2025-07-26 10:16 25 ****** 48 2025-07-26 11:15 ? - 49 2025-07-26 12:14 33 ************** 50 2025-07-26 13:13 ? - 51 2025-07-26 14:12 34 *************** 52 2025-07-26 15:11 ? - 53 2025-07-26 16:10 34 *************** 54 2025-07-26 17:09 34 *************** 55 2025-07-26 18:08 36 ***************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 363 --- Lifetime Power-On Resets 0x01 0x010 4 9383 --- Power-on Hours 0x01 0x018 6 202680696127 --- Logical Sectors Written 0x01 0x020 6 871989604 --- Number of Write Commands 0x01 0x028 6 15426549518992 --- Logical Sectors Read 0x01 0x030 6 9624403052 --- Number of Read Commands 0x01 0x038 6 - --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 7772 --- Spindle Motor Power-on Hours 0x03 0x010 4 6048 --- Head Flying Hours 0x03 0x018 4 4693 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x03 0x040 4 49 --- Number of High Priority Unload Events 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 2 --- Resets Between Cmd Acceptance and Completion 0x04 0x018 4 0 -D- Physical Element Status Changed 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 35 --- Current Temperature 0x05 0x010 1 36 --- Average Short Term Temperature 0x05 0x018 1 38 --- Average Long Term Temperature 0x05 0x020 1 52 --- Highest Temperature 0x05 0x028 1 25 --- Lowest Temperature 0x05 0x030 1 48 --- Highest Average Short Term Temperature 0x05 0x038 1 26 --- Lowest Average Short Term Temperature 0x05 0x040 1 41 --- Highest Average Long Term Temperature 0x05 0x048 1 28 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 1318 --- Number of Hardware Resets 0x06 0x010 4 130 --- Number of ASR Events 0x06 0x018 4 1 --- Number of Interface CRC Errors 0xff ===== = = === == Vendor Specific Statistics (rev 1) == 0xff 0x008 7 0 --- Vendor Specific 0xff 0x010 7 0 --- Vendor Specific 0xff 0x018 7 0 --- Vendor Specific |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 13 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.0-37-amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD60EFRX-68MYMN1 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 82.00A82 User Capacity: 6,001,175,126,016 bytes [6.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5700 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Jul 26 18:58:15 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2984) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 684) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 219 196 021 - 8025 4 Start_Stop_Count -O--CK 090 090 000 - 10474 5 Reallocated_Sector_Ct PO--CK 144 144 140 - 1646 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 001 001 000 - 78417 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 254 192 Power-Off_Retract_Count -O--CK 200 200 000 - 171 193 Load_Cycle_Count -O--CK 193 193 000 - 22750 194 Temperature_Celsius -O---K 118 105 000 - 34 196 Reallocated_Event_Count -O--CK 127 127 000 - 73 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 2 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 40 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 66 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 66 [17] occurred at disk power-on lifetime: 11706 hours (487 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 7f 00 00 02 b0 01 c8 40 00 Error: UNC at LBA = 0x02b001c8 = 45089224 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 d8 00 00 a9 ff b3 40 40 08 12d+04:01:50.526 READ FPDMA QUEUED 60 04 00 00 88 00 00 02 b0 04 00 40 08 12d+04:01:50.510 READ FPDMA QUEUED 60 04 00 00 80 00 00 02 b0 00 00 40 08 12d+04:01:50.510 READ FPDMA QUEUED 60 04 00 00 78 00 00 02 af fc 00 40 08 12d+04:01:50.510 READ FPDMA QUEUED 60 04 00 00 70 00 00 02 af f8 00 40 08 12d+04:01:50.510 READ FPDMA QUEUED Error 65 [16] occurred at disk power-on lifetime: 11202 hours (466 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 b2 c7 c8 40 00 Error: UNC at LBA = 0x02b2c7c8 = 45270984 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 04 00 00 f8 00 00 02 b0 08 00 40 08 21:00:36.104 READ FPDMA QUEUED 60 04 00 00 88 00 00 02 b0 04 00 40 08 21:00:34.879 READ FPDMA QUEUED 60 04 00 00 80 00 00 02 b0 00 00 40 08 21:00:34.879 READ FPDMA QUEUED 60 04 00 00 78 00 00 02 af fc 00 40 08 21:00:34.879 READ FPDMA QUEUED 60 04 00 00 70 00 00 02 af f8 00 40 08 21:00:34.879 READ FPDMA QUEUED Error 64 [15] occurred at disk power-on lifetime: 7261 hours (302 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 b3 c3 a8 40 00 Error: UNC at LBA = 0x02b3c3a8 = 45335464 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 10 00 00 02 b3 c3 a8 40 08 13d+23:03:24.177 READ FPDMA QUEUED 60 00 08 00 08 00 00 02 b3 c3 a0 40 08 13d+23:03:24.177 READ FPDMA QUEUED 60 00 80 00 80 00 00 02 b3 f3 00 40 08 13d+23:03:24.163 READ FPDMA QUEUED 60 00 08 00 78 00 00 02 b3 c4 f8 40 08 13d+23:03:24.158 READ FPDMA QUEUED 60 00 08 00 70 00 00 02 b3 c4 f0 40 08 13d+23:03:24.158 READ FPDMA QUEUED Error 63 [14] occurred at disk power-on lifetime: 7261 hours (302 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 b3 c3 a8 40 00 Error: UNC at LBA = 0x02b3c3a8 = 45335464 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 00 00 00 02 b3 e7 00 40 08 13d+23:03:19.942 READ FPDMA QUEUED 60 00 80 00 50 00 00 02 b3 e4 00 40 08 13d+23:03:19.929 READ FPDMA QUEUED 61 00 08 00 48 00 00 02 b3 99 f8 40 08 13d+23:03:19.911 WRITE FPDMA QUEUED 61 00 08 00 40 00 00 02 b3 99 f0 40 08 13d+23:03:19.911 WRITE FPDMA QUEUED 61 00 08 00 38 00 00 02 b3 99 e8 40 08 13d+23:03:19.911 WRITE FPDMA QUEUED Error 62 [13] occurred at disk power-on lifetime: 7261 hours (302 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 b3 99 e8 40 00 Error: UNC at LBA = 0x02b399e8 = 45324776 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 e8 00 00 02 b3 c0 00 40 08 13d+23:03:15.713 READ FPDMA QUEUED 60 00 08 00 e0 00 00 02 b3 99 e8 40 08 13d+23:03:15.713 READ FPDMA QUEUED 60 00 08 00 b8 00 00 02 b3 99 e0 40 08 13d+23:03:15.713 READ FPDMA QUEUED 60 00 08 00 b0 00 00 02 b3 99 d8 40 08 13d+23:03:15.702 READ FPDMA QUEUED 60 00 08 00 a8 00 00 02 b3 99 d0 40 08 13d+23:03:15.700 READ FPDMA QUEUED Error 61 [12] occurred at disk power-on lifetime: 7261 hours (302 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 b3 99 e8 40 00 Error: UNC at LBA = 0x02b399e8 = 45324776 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 80 00 c8 00 00 02 b3 a2 80 40 08 13d+23:03:11.634 READ FPDMA QUEUED 60 02 80 00 c0 00 00 02 b3 9f 80 40 08 13d+23:03:11.634 READ FPDMA QUEUED 60 02 80 00 b8 00 00 02 b3 9c 80 40 08 13d+23:03:11.634 READ FPDMA QUEUED 60 02 80 00 b0 00 00 02 b3 99 80 40 08 13d+23:03:11.634 READ FPDMA QUEUED 60 02 80 00 a8 00 00 02 b3 96 80 40 08 13d+23:03:11.634 READ FPDMA QUEUED Error 60 [11] occurred at disk power-on lifetime: 7261 hours (302 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 b3 70 28 40 00 Error: UNC at LBA = 0x02b37028 = 45314088 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 e0 00 00 02 b3 93 00 40 08 13d+23:03:07.498 READ FPDMA QUEUED 60 00 08 00 d0 00 00 02 b3 70 28 40 08 13d+23:03:07.488 READ FPDMA QUEUED 60 00 08 00 c8 00 00 02 b3 70 20 40 08 13d+23:03:07.488 READ FPDMA QUEUED 60 00 08 00 c0 00 00 02 b3 70 18 40 08 13d+23:03:07.486 READ FPDMA QUEUED 60 00 80 00 88 00 00 02 b3 90 00 40 08 13d+23:03:07.479 READ FPDMA QUEUED Error 59 [10] occurred at disk power-on lifetime: 7261 hours (302 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 b3 7e 18 40 00 Error: UNC at LBA = 0x02b37e18 = 45317656 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 a8 00 00 02 b3 70 10 40 08 13d+23:03:03.469 READ FPDMA QUEUED 60 00 08 00 a0 00 00 02 b3 71 f8 40 08 13d+23:03:03.453 READ FPDMA QUEUED 60 00 08 00 c8 00 00 02 b3 71 78 40 08 13d+23:03:03.453 READ FPDMA QUEUED 60 00 08 00 c0 00 00 02 b3 70 f8 40 08 13d+23:03:03.453 READ FPDMA QUEUED 60 00 08 00 98 00 00 02 b3 71 f0 40 08 13d+23:03:03.453 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 12751 - # 2 Short offline Completed without error 00% 12579 - # 3 Short offline Completed without error 00% 12410 - # 4 Short offline Completed without error 00% 12256 - # 5 Short offline Completed without error 00% 12074 - # 6 Short offline Completed without error 00% 11906 - # 7 Short offline Completed without error 00% 11761 - # 8 Short offline Completed without error 00% 11587 - # 9 Short offline Completed without error 00% 11415 - #10 Short offline Completed without error 00% 11280 - #11 Short offline Completed without error 00% 11251 - #12 Short offline Completed without error 00% 11022 - #13 Short offline Completed without error 00% 10854 - #14 Short offline Completed without error 00% 10686 - #15 Short offline Completed without error 00% 10518 - #16 Short offline Completed without error 00% 10350 - #17 Short offline Completed without error 00% 10194 - #18 Short offline Completed without error 00% 1145 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 34/34 Celsius Lifetime Min/Max Temperature: 2/47 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (192) Index Estimated Time Temperature Celsius 193 2025-07-26 11:01 34 *************** ... ..( 29 skipped). .. *************** 223 2025-07-26 11:31 34 *************** 224 2025-07-26 11:32 ? - 225 2025-07-26 11:33 35 **************** 226 2025-07-26 11:34 ? - 227 2025-07-26 11:35 35 **************** ... ..( 20 skipped). .. **************** 248 2025-07-26 11:56 35 **************** 249 2025-07-26 11:57 34 *************** ... ..( 9 skipped). .. *************** 259 2025-07-26 12:07 34 *************** 260 2025-07-26 12:08 ? - 261 2025-07-26 12:09 34 *************** ... ..( 3 skipped). .. *************** 265 2025-07-26 12:13 34 *************** 266 2025-07-26 12:14 ? - 267 2025-07-26 12:15 34 *************** ... ..( 64 skipped). .. *************** 332 2025-07-26 13:20 34 *************** 333 2025-07-26 13:21 ? - 334 2025-07-26 13:22 34 *************** 335 2025-07-26 13:23 ? - 336 2025-07-26 13:24 34 *************** ... ..( 75 skipped). .. *************** 412 2025-07-26 14:40 34 *************** 413 2025-07-26 14:41 ? - 414 2025-07-26 14:42 34 *************** ... ..( 2 skipped). .. *************** 417 2025-07-26 14:45 34 *************** 418 2025-07-26 14:46 ? - 419 2025-07-26 14:47 34 *************** ... ..( 62 skipped). .. *************** 4 2025-07-26 15:50 34 *************** 5 2025-07-26 15:51 ? - 6 2025-07-26 15:52 34 *************** ... ..( 11 skipped). .. *************** 18 2025-07-26 16:04 34 *************** 19 2025-07-26 16:05 35 **************** ... ..( 9 skipped). .. **************** 29 2025-07-26 16:15 35 **************** 30 2025-07-26 16:16 ? - 31 2025-07-26 16:17 36 ***************** 32 2025-07-26 16:18 35 **************** ... ..( 2 skipped). .. **************** 35 2025-07-26 16:21 35 **************** 36 2025-07-26 16:22 ? - 37 2025-07-26 16:23 25 ****** 38 2025-07-26 16:24 ? - 39 2025-07-26 16:25 25 ****** 40 2025-07-26 16:26 25 ****** 41 2025-07-26 16:27 26 ******* 42 2025-07-26 16:28 26 ******* 43 2025-07-26 16:29 27 ******** 44 2025-07-26 16:30 27 ******** 45 2025-07-26 16:31 28 ********* 46 2025-07-26 16:32 28 ********* 47 2025-07-26 16:33 28 ********* 48 2025-07-26 16:34 29 ********** ... ..( 2 skipped). .. ********** 51 2025-07-26 16:37 29 ********** 52 2025-07-26 16:38 30 *********** 53 2025-07-26 16:39 30 *********** 54 2025-07-26 16:40 30 *********** 55 2025-07-26 16:41 31 ************ ... ..( 5 skipped). .. ************ 61 2025-07-26 16:47 31 ************ 62 2025-07-26 16:48 32 ************* ... ..( 6 skipped). .. ************* 69 2025-07-26 16:55 32 ************* 70 2025-07-26 16:56 33 ************** 71 2025-07-26 16:57 ? - 72 2025-07-26 16:58 33 ************** 73 2025-07-26 16:59 ? - 74 2025-07-26 17:00 34 *************** 75 2025-07-26 17:01 33 ************** ... ..( 9 skipped). .. ************** 85 2025-07-26 17:11 33 ************** 86 2025-07-26 17:12 34 *************** ... ..(105 skipped). .. *************** 192 2025-07-26 18:58 34 *************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 784 Vendor specific /dev/sdc smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.0-37-amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: ST18000NE000-2YY101 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: EN01 User Capacity: 18,000,207,937,536 bytes [18.0 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database 7.3/5319 ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Jul 26 18:58:15 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Disabled ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: scsi error badly formed scsi parameters Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 567) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: (1556) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x50bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 077 064 044 - 51609526 3 Spin_Up_Time PO---- 089 087 000 - 0 4 Start_Stop_Count -O--CK 099 099 020 - 1642 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 090 060 045 - 924188150 9 Power_On_Hours -O--CK 087 087 000 - 12057 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 366 18 Unknown_Attribute PO-R-- 100 100 050 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 066 050 000 - 34 (Min/Max 33/35) 192 Power-Off_Retract_Count -O--CK 100 100 000 - 56 193 Load_Cycle_Count -O--CK 096 096 000 - 8173 194 Temperature_Celsius -O---K 034 050 000 - 34 (0 17 0 0 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate PO---K 100 100 001 - 0 240 Head_Flying_Hours ------ 100 253 000 - 6522 (228 147 0) 241 Total_LBAs_Written ------ 100 253 000 - 196567370416 242 Total_LBAs_Read ------ 100 253 000 - 17943034538634 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL R/O 256 Device Statistics log 0x04 SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0a GPL R/W 8 Device Statistics Notification 0x0c GPL R/O 2048 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 768 Current Device Internal Status Data log 0x2f GPL - 1 Set Sector Configuration 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 160 Device vendor specific log 0xa2 GPL VS 16320 Device vendor specific log 0xa4 GPL,SL VS 160 Device vendor specific log 0xa6 GPL VS 192 Device vendor specific log 0xa8-0xa9 GPL,SL VS 136 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xad GPL VS 16 Device vendor specific log 0xb1 GPL,SL VS 160 Device vendor specific log 0xb6 GPL VS 1920 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc1 GPL,SL VS 8 Device vendor specific log 0xc3 GPL,SL VS 24 Device vendor specific log 0xc6 GPL VS 5184 Device vendor specific log 0xc7 GPL,SL VS 8 Device vendor specific log 0xc9 GPL,SL VS 8 Device vendor specific log 0xca GPL,SL VS 16 Device vendor specific log 0xcd GPL,SL VS 1 Device vendor specific log 0xce GPL VS 1 Device vendor specific log 0xcf GPL VS 512 Device vendor specific log 0xd1 GPL VS 656 Device vendor specific log 0xd2 GPL VS 10256 Device vendor specific log 0xd4 GPL VS 2048 Device vendor specific log 0xda GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 11990 - # 2 Short offline Completed without error 00% 11679 - # 3 Short offline Completed without error 00% 11511 - # 4 Short offline Completed without error 00% 11343 - # 5 Short offline Completed without error 00% 11175 - # 6 Short offline Completed without error 00% 11007 - # 7 Short offline Completed without error 00% 10843 - # 8 Short offline Completed without error 00% 10679 - # 9 Short offline Completed without error 00% 10537 - #10 Short offline Completed without error 00% 10423 - #11 Short offline Completed without error 00% 10251 - #12 Short offline Completed without error 00% 10089 - #13 Short offline Completed without error 00% 9922 - #14 Short offline Completed without error 00% 9745 - #15 Short offline Completed without error 00% 9580 - #16 Short offline Completed without error 00% 9434 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 33/35 Celsius Lifetime Min/Max Temperature: 17/51 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) Vendor specific: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 4 minutes Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 10/40 Celsius Min/Max Temperature Limit: 5/60 Celsius Temperature History Size (Index): 128 (48) Index Estimated Time Temperature Celsius 49 2025-07-21 13:15 37 ****************** 50 2025-07-21 14:14 40 ********************* 51 2025-07-21 15:13 37 ****************** ... ..( 5 skipped). .. ****************** 57 2025-07-21 21:07 37 ****************** 58 2025-07-21 22:06 42 *********************** 59 2025-07-21 23:05 37 ****************** ... ..( 5 skipped). .. ****************** 65 2025-07-22 04:59 37 ****************** 66 2025-07-22 05:58 38 ******************* ... ..( 2 skipped). .. ******************* 69 2025-07-22 08:55 38 ******************* 70 2025-07-22 09:54 ? - 71 2025-07-22 10:53 38 ******************* 72 2025-07-22 11:52 36 ***************** 73 2025-07-22 12:51 ? - 74 2025-07-22 13:50 30 *********** 75 2025-07-22 14:49 ? - 76 2025-07-22 15:48 31 ************ 77 2025-07-22 16:47 34 *************** 78 2025-07-22 17:46 ? - 79 2025-07-22 18:45 24 ***** 80 2025-07-22 19:44 36 ***************** 81 2025-07-22 20:43 ? - 82 2025-07-22 21:42 24 ***** 83 2025-07-22 22:41 36 ***************** 84 2025-07-22 23:40 42 *********************** ... ..( 4 skipped). .. *********************** 89 2025-07-23 04:35 42 *********************** 90 2025-07-23 05:34 35 **************** ... ..( 5 skipped). .. **************** 96 2025-07-23 11:28 35 **************** 97 2025-07-23 12:27 38 ******************* 98 2025-07-23 13:26 35 **************** ... ..( 4 skipped). .. **************** 103 2025-07-23 18:21 35 **************** 104 2025-07-23 19:20 36 ***************** 105 2025-07-23 20:19 35 **************** ... ..( 2 skipped). .. **************** 108 2025-07-23 23:16 35 **************** 109 2025-07-24 00:15 38 ******************* 110 2025-07-24 01:14 35 **************** 111 2025-07-24 02:13 35 **************** 112 2025-07-24 03:12 35 **************** 113 2025-07-24 04:11 38 ******************* 114 2025-07-24 05:10 35 **************** 115 2025-07-24 06:09 35 **************** 116 2025-07-24 07:08 35 **************** 117 2025-07-24 08:07 36 ***************** 118 2025-07-24 09:06 36 ***************** 119 2025-07-24 10:05 36 ***************** 120 2025-07-24 11:04 35 **************** 121 2025-07-24 12:03 39 ******************** 122 2025-07-24 13:02 ? - 123 2025-07-24 14:01 33 ************** 124 2025-07-24 15:00 34 *************** 125 2025-07-24 15:59 ? - 126 2025-07-24 16:58 26 ******* 127 2025-07-24 17:57 34 *************** 0 2025-07-24 18:56 36 ***************** 1 2025-07-24 19:55 35 **************** 2 2025-07-24 20:54 ? - 3 2025-07-24 21:53 39 ******************** 4 2025-07-24 22:52 ? - 5 2025-07-24 23:51 37 ****************** 6 2025-07-25 00:50 ? - 7 2025-07-25 01:49 37 ****************** 8 2025-07-25 02:48 33 ************** 9 2025-07-25 03:47 34 *************** 10 2025-07-25 04:46 ? - 11 2025-07-25 05:45 25 ****** 12 2025-07-25 06:44 ? - 13 2025-07-25 07:43 33 ************** 14 2025-07-25 08:42 ? - 15 2025-07-25 09:41 26 ******* 16 2025-07-25 10:40 ? - 17 2025-07-25 11:39 28 ********* 18 2025-07-25 12:38 ? - 19 2025-07-25 13:37 28 ********* 20 2025-07-25 14:36 34 *************** 21 2025-07-25 15:35 33 ************** 22 2025-07-25 16:34 34 *************** 23 2025-07-25 17:33 ? - 24 2025-07-25 18:32 34 *************** 25 2025-07-25 19:31 ? - 26 2025-07-25 20:30 25 ****** 27 2025-07-25 21:29 33 ************** 28 2025-07-25 22:28 ? - 29 2025-07-25 23:27 34 *************** 30 2025-07-26 00:26 ? - 31 2025-07-26 01:25 34 *************** 32 2025-07-26 02:24 ? - 33 2025-07-26 03:23 34 *************** 34 2025-07-26 04:22 ? - 35 2025-07-26 05:21 35 **************** 36 2025-07-26 06:20 33 ************** 37 2025-07-26 07:19 ? - 38 2025-07-26 08:18 33 ************** 39 2025-07-26 09:17 ? - 40 2025-07-26 10:16 25 ****** 41 2025-07-26 11:15 ? - 42 2025-07-26 12:14 33 ************** 43 2025-07-26 13:13 ? - 44 2025-07-26 14:12 33 ************** 45 2025-07-26 15:11 ? - 46 2025-07-26 16:10 33 ************** 47 2025-07-26 17:09 33 ************** 48 2025-07-26 18:08 35 **************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 366 --- Lifetime Power-On Resets 0x01 0x010 4 12057 --- Power-on Hours 0x01 0x018 6 196557791884 --- Logical Sectors Written 0x01 0x020 6 466502214 --- Number of Write Commands 0x01 0x028 6 17938725960790 --- Logical Sectors Read 0x01 0x030 6 81869002787 --- Number of Read Commands 0x01 0x038 6 - --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 10164 --- Spindle Motor Power-on Hours 0x03 0x010 4 6758 --- Head Flying Hours 0x03 0x018 4 8173 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x03 0x040 4 56 --- Number of High Priority Unload Events 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x04 0x018 4 0 -D- Physical Element Status Changed 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 34 --- Current Temperature 0x05 0x010 1 34 --- Average Short Term Temperature 0x05 0x018 1 37 --- Average Long Term Temperature 0x05 0x020 1 50 --- Highest Temperature 0x05 0x028 1 24 --- Lowest Temperature 0x05 0x030 1 46 --- Highest Average Short Term Temperature 0x05 0x038 1 24 --- Lowest Average Short Term Temperature 0x05 0x040 1 39 --- Highest Average Long Term Temperature 0x05 0x048 1 27 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 1147 --- Number of Hardware Resets 0x06 0x010 4 58 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0xff ===== = = === == Vendor Specific Statistics (rev 1) == 0xff 0x008 7 0 --- Vendor Specific 0xff 0x010 7 0 --- Vendor Specific 0xff 0x018 7 0 --- Vendor Specific |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 13 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdd smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.0-37-amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD60EFRX-68L0BN1 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 82.00A82 User Capacity: 6,001,175,126,016 bytes [6.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5700 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Jul 26 18:58:16 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7184) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 725) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 152 051 - 0 3 Spin_Up_Time POS--K 253 196 021 - 5091 4 Start_Stop_Count -O--CK 091 091 000 - 9542 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 004 004 000 - 70308 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 245 192 Power-Off_Retract_Count -O--CK 200 200 000 - 170 193 Load_Cycle_Count -O--CK 194 194 000 - 20937 194 Temperature_Celsius -O---K 117 106 000 - 35 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 9 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 40 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 790 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 790 [21] occurred at disk power-on lifetime: 4328 hours (180 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 ba 3b 5a 30 40 00 Error: WP at LBA = 0x2ba3b5a30 = 11714386480 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 20 00 e0 00 02 ba 3b 3e 00 40 08 42d+15:00:54.038 WRITE FPDMA QUEUED 61 00 40 00 b8 00 02 ba 3b 3f 00 40 08 42d+15:00:54.038 WRITE FPDMA QUEUED 60 02 00 00 b0 00 02 ba 3b 5d 80 40 08 42d+15:00:54.038 READ FPDMA QUEUED 60 04 00 00 a8 00 02 ba 3b 59 00 40 08 42d+15:00:54.037 READ FPDMA QUEUED 60 04 00 00 a0 00 02 ba 3b 55 00 40 08 42d+15:00:54.037 READ FPDMA QUEUED Error 789 [20] occurred at disk power-on lifetime: 4328 hours (180 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 ba 3b 53 a0 40 00 Error: WP at LBA = 0x2ba3b53a0 = 11714384800 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 20 00 30 00 02 ba 3b 3c e0 40 08 42d+15:00:50.083 WRITE FPDMA QUEUED 60 00 20 00 28 00 02 ba 3f 8b e0 40 08 42d+15:00:50.083 READ FPDMA QUEUED 61 00 80 00 10 00 02 ba 3b 40 00 40 08 42d+15:00:50.083 WRITE FPDMA QUEUED 60 00 08 00 08 00 02 ba 3b 3f 80 40 08 42d+15:00:50.083 READ FPDMA QUEUED 61 00 40 00 00 00 02 ba 3b 3d 80 40 08 42d+15:00:50.083 WRITE FPDMA QUEUED Error 788 [19] occurred at disk power-on lifetime: 4328 hours (180 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 ba 3b 4d 20 40 00 Error: UNC at LBA = 0x2ba3b4d20 = 11714383136 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 80 00 02 ba 3b 3f 78 40 08 42d+15:00:45.966 READ FPDMA QUEUED 60 00 08 00 78 00 02 ba 3b 3f 70 40 08 42d+15:00:45.966 READ FPDMA QUEUED 60 00 20 00 d8 00 02 ba 3f 8b e0 40 08 42d+15:00:45.938 READ FPDMA QUEUED 60 00 80 00 70 00 02 ba 3b 6e 80 40 08 42d+15:00:45.938 READ FPDMA QUEUED 60 00 08 00 d0 00 02 ba 3b 3f 68 40 08 42d+15:00:45.938 READ FPDMA QUEUED Error 787 [18] occurred at disk power-on lifetime: 4328 hours (180 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 ba 3b 40 58 40 00 Error: UNC at LBA = 0x2ba3b4058 = 11714379864 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 68 00 00 00 51 c1 20 40 08 42d+15:00:40.791 READ FPDMA QUEUED 60 04 00 00 38 00 02 ba 3b 41 00 40 08 42d+15:00:40.791 READ FPDMA QUEUED 60 04 00 00 30 00 02 ba 3b 3d 00 40 08 42d+15:00:40.791 READ FPDMA QUEUED 47 00 00 00 01 00 00 00 00 00 30 e0 08 42d+15:00:40.791 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 00 e0 08 42d+15:00:40.790 READ LOG DMA EXT Error 786 [17] occurred at disk power-on lifetime: 4328 hours (180 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 ba 3b 39 d0 40 00 Error: UNC at LBA = 0x2ba3b39d0 = 11714378192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 58 00 00 00 51 c1 20 40 08 42d+15:00:36.800 READ FPDMA QUEUED 60 04 00 00 50 00 02 ba 3b 41 00 40 08 42d+15:00:36.800 READ FPDMA QUEUED 60 04 00 00 48 00 02 ba 3b 3d 00 40 08 42d+15:00:36.799 READ FPDMA QUEUED 60 04 00 00 40 00 02 ba 3b 39 00 40 08 42d+15:00:36.799 READ FPDMA QUEUED 60 04 00 00 38 00 02 ba 3b 35 00 40 08 42d+15:00:36.799 READ FPDMA QUEUED Error 785 [16] occurred at disk power-on lifetime: 4328 hours (180 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 ba 3b 2c a0 40 00 Error: UNC at LBA = 0x2ba3b2ca0 = 11714374816 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 03 80 00 60 00 02 ba 3b 31 80 40 08 42d+15:00:31.502 READ FPDMA QUEUED 60 00 80 00 58 00 02 ba 3b 30 80 40 08 42d+15:00:31.501 READ FPDMA QUEUED 60 01 80 00 50 00 02 ba 3b 2f 00 40 08 42d+15:00:31.501 READ FPDMA QUEUED 60 01 00 00 48 00 02 ba 3b 2d 80 40 08 42d+15:00:31.501 READ FPDMA QUEUED 60 01 80 00 40 00 02 ba 3b 2b 80 40 08 42d+15:00:31.501 READ FPDMA QUEUED Error 784 [15] occurred at disk power-on lifetime: 4328 hours (180 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 ba 3b 05 98 40 00 Error: UNC at LBA = 0x2ba3b0598 = 11714364824 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 b8 00 00 00 57 74 00 40 08 42d+15:00:27.247 READ FPDMA QUEUED 60 04 00 00 b0 00 02 ba 3b 0b 00 40 08 42d+15:00:27.247 READ FPDMA QUEUED 60 04 00 00 a8 00 02 ba 3b 07 00 40 08 42d+15:00:27.247 READ FPDMA QUEUED 60 02 00 00 a0 00 02 ba 3b 05 00 40 08 42d+15:00:27.247 READ FPDMA QUEUED 60 02 00 00 78 00 02 ba 3b 02 80 40 08 42d+15:00:27.246 READ FPDMA QUEUED Error 783 [14] occurred at disk power-on lifetime: 4328 hours (180 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 ba 3a c4 50 40 00 Error: UNC at LBA = 0x2ba3ac450 = 11714348112 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 c0 00 02 ba 3f f9 a0 40 08 42d+15:00:20.300 READ FPDMA QUEUED 60 04 00 00 b8 00 02 ba 3a c5 00 40 08 42d+15:00:20.300 READ FPDMA QUEUED 60 04 00 00 a8 00 02 ba 3a c1 00 40 08 42d+15:00:20.297 READ FPDMA QUEUED 60 04 00 00 78 00 02 ba 3a bd 00 40 08 42d+15:00:20.297 READ FPDMA QUEUED 60 04 00 00 70 00 02 ba 3a b9 00 40 08 42d+15:00:20.297 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 4602 - # 2 Short offline Completed without error 00% 4445 - # 3 Short offline Completed without error 00% 4278 - # 4 Short offline Completed without error 00% 4109 - # 5 Short offline Completed without error 00% 44136 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 35/35 Celsius Lifetime Min/Max Temperature: 2/46 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (368) Index Estimated Time Temperature Celsius 369 2025-07-26 11:01 34 *************** ... ..( 56 skipped). .. *************** 426 2025-07-26 11:58 34 *************** 427 2025-07-26 11:59 35 **************** 428 2025-07-26 12:00 ? - 429 2025-07-26 12:01 35 **************** 430 2025-07-26 12:02 ? - 431 2025-07-26 12:03 35 **************** ... ..( 31 skipped). .. **************** 463 2025-07-26 12:35 35 **************** 464 2025-07-26 12:36 ? - 465 2025-07-26 12:37 35 **************** ... ..( 3 skipped). .. **************** 469 2025-07-26 12:41 35 **************** 470 2025-07-26 12:42 ? - 471 2025-07-26 12:43 35 **************** ... ..( 64 skipped). .. **************** 58 2025-07-26 13:48 35 **************** 59 2025-07-26 13:49 ? - 60 2025-07-26 13:50 35 **************** 61 2025-07-26 13:51 ? - 62 2025-07-26 13:52 35 **************** ... ..( 75 skipped). .. **************** 138 2025-07-26 15:08 35 **************** 139 2025-07-26 15:09 ? - 140 2025-07-26 15:10 35 **************** ... ..( 2 skipped). .. **************** 143 2025-07-26 15:13 35 **************** 144 2025-07-26 15:14 ? - 145 2025-07-26 15:15 35 **************** ... ..( 62 skipped). .. **************** 208 2025-07-26 16:18 35 **************** 209 2025-07-26 16:19 ? - 210 2025-07-26 16:20 35 **************** ... ..( 22 skipped). .. **************** 233 2025-07-26 16:43 35 **************** 234 2025-07-26 16:44 ? - 235 2025-07-26 16:45 35 **************** ... ..( 3 skipped). .. **************** 239 2025-07-26 16:49 35 **************** 240 2025-07-26 16:50 ? - 241 2025-07-26 16:51 25 ****** 242 2025-07-26 16:52 ? - 243 2025-07-26 16:53 25 ****** 244 2025-07-26 16:54 25 ****** 245 2025-07-26 16:55 26 ******* 246 2025-07-26 16:56 26 ******* 247 2025-07-26 16:57 27 ******** 248 2025-07-26 16:58 27 ******** 249 2025-07-26 16:59 27 ******** 250 2025-07-26 17:00 28 ********* 251 2025-07-26 17:01 28 ********* 252 2025-07-26 17:02 28 ********* 253 2025-07-26 17:03 29 ********** ... ..( 2 skipped). .. ********** 256 2025-07-26 17:06 29 ********** 257 2025-07-26 17:07 30 *********** 258 2025-07-26 17:08 30 *********** 259 2025-07-26 17:09 30 *********** 260 2025-07-26 17:10 31 ************ ... ..( 4 skipped). .. ************ 265 2025-07-26 17:15 31 ************ 266 2025-07-26 17:16 32 ************* ... ..( 7 skipped). .. ************* 274 2025-07-26 17:24 32 ************* 275 2025-07-26 17:25 ? - 276 2025-07-26 17:26 33 ************** 277 2025-07-26 17:27 ? - 278 2025-07-26 17:28 34 *************** ... ..( 89 skipped). .. *************** 368 2025-07-26 18:58 34 *************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 793 Vendor specific


Hardware for Linux and BSD

GitHub