/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD1600BEVT-22A23T0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 160 041 885 696 bytes [160 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Thu Apr 7 11:53:55 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 96 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6000) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 73) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 200 3 Spin_Up_Time POS--K 152 137 021 - 1383 4 Start_Stop_Count -O--CK 084 084 000 - 16334 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 096 096 000 - 3644 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1836 191 G-Sense_Error_Rate -O--CK 001 001 000 - 10278 192 Power-Off_Retract_Count -O--CK 200 200 000 - 616 193 Load_Cycle_Count -O--CK 125 125 000 - 226755 194 Temperature_Celsius -O---K 101 092 000 - 42 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 200 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 200 [7] occurred at disk power-on lifetime: 1564 hours (65 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 02 bf a4 15 40 00 Error: UNC at LBA = 0x02bfa415 = 46113813 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 01 00 00 02 bf a4 15 40 00 00:15:38.655 READ VERIFY SECTOR(S) EXT 42 00 00 00 01 00 00 02 bf a4 15 40 00 00:15:36.069 READ VERIFY SECTOR(S) EXT 60 00 01 00 30 00 00 00 00 00 00 40 00 00:15:36.069 READ FPDMA QUEUED 42 00 00 00 01 00 00 02 bf a4 15 40 00 00:15:33.483 READ VERIFY SECTOR(S) EXT 42 00 00 00 01 00 00 02 bf a4 15 40 00 00:15:30.896 READ VERIFY SECTOR(S) EXT Error 199 [6] occurred at disk power-on lifetime: 1564 hours (65 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 02 bf a4 15 40 00 Error: UNC at LBA = 0x02bfa415 = 46113813 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 01 00 00 02 bf a4 15 40 00 00:15:36.069 READ VERIFY SECTOR(S) EXT 60 00 01 00 30 00 00 00 00 00 00 40 00 00:15:36.069 READ FPDMA QUEUED 42 00 00 00 01 00 00 02 bf a4 15 40 00 00:15:33.483 READ VERIFY SECTOR(S) EXT 42 00 00 00 01 00 00 02 bf a4 15 40 00 00:15:30.896 READ VERIFY SECTOR(S) EXT 60 00 01 00 98 00 00 00 00 00 00 40 00 00:15:30.896 READ FPDMA QUEUED Error 198 [5] occurred at disk power-on lifetime: 1564 hours (65 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 02 bf a4 15 40 00 Error: UNC at LBA = 0x02bfa415 = 46113813 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 01 00 00 02 bf a4 15 40 00 00:15:33.483 READ VERIFY SECTOR(S) EXT 42 00 00 00 01 00 00 02 bf a4 15 40 00 00:15:30.896 READ VERIFY SECTOR(S) EXT 60 00 01 00 98 00 00 00 00 00 00 40 00 00:15:30.896 READ FPDMA QUEUED 42 00 00 00 01 00 00 02 bf a4 15 40 00 00:15:28.310 READ VERIFY SECTOR(S) EXT 60 00 01 00 60 00 00 00 00 00 00 40 00 00:15:28.310 READ FPDMA QUEUED Error 197 [4] occurred at disk power-on lifetime: 1564 hours (65 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 02 bf a4 15 40 00 Error: UNC at LBA = 0x02bfa415 = 46113813 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 01 00 00 02 bf a4 15 40 00 00:15:30.896 READ VERIFY SECTOR(S) EXT 60 00 01 00 98 00 00 00 00 00 00 40 00 00:15:30.896 READ FPDMA QUEUED 42 00 00 00 01 00 00 02 bf a4 15 40 00 00:15:28.310 READ VERIFY SECTOR(S) EXT 60 00 01 00 60 00 00 00 00 00 00 40 00 00:15:28.310 READ FPDMA QUEUED 42 00 00 00 02 00 00 02 bf a4 15 40 00 00:15:25.724 READ VERIFY SECTOR(S) EXT Error 196 [3] occurred at disk power-on lifetime: 1564 hours (65 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 02 bf a4 15 40 00 Error: UNC at LBA = 0x02bfa415 = 46113813 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 01 00 00 02 bf a4 15 40 00 00:15:28.310 READ VERIFY SECTOR(S) EXT 60 00 01 00 60 00 00 00 00 00 00 40 00 00:15:28.310 READ FPDMA QUEUED 42 00 00 00 02 00 00 02 bf a4 15 40 00 00:15:25.724 READ VERIFY SECTOR(S) EXT 42 00 00 00 02 00 00 02 bf a4 15 40 00 00:15:23.137 READ VERIFY SECTOR(S) EXT 42 00 00 00 02 00 00 02 bf a4 15 40 00 00:15:20.551 READ VERIFY SECTOR(S) EXT Error 195 [2] occurred at disk power-on lifetime: 1564 hours (65 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 02 bf a4 15 40 00 Error: UNC at LBA = 0x02bfa415 = 46113813 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 02 00 00 02 bf a4 15 40 00 00:15:25.724 READ VERIFY SECTOR(S) EXT 42 00 00 00 02 00 00 02 bf a4 15 40 00 00:15:23.137 READ VERIFY SECTOR(S) EXT 42 00 00 00 02 00 00 02 bf a4 15 40 00 00:15:20.551 READ VERIFY SECTOR(S) EXT 60 00 01 00 f0 00 00 00 00 00 00 40 00 00:15:20.551 READ FPDMA QUEUED 42 00 00 00 02 00 00 02 bf a4 15 40 00 00:15:17.965 READ VERIFY SECTOR(S) EXT Error 194 [1] occurred at disk power-on lifetime: 1564 hours (65 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 02 bf a4 15 40 00 Error: UNC at LBA = 0x02bfa415 = 46113813 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 02 00 00 02 bf a4 15 40 00 00:15:23.137 READ VERIFY SECTOR(S) EXT 42 00 00 00 02 00 00 02 bf a4 15 40 00 00:15:20.551 READ VERIFY SECTOR(S) EXT 60 00 01 00 f0 00 00 00 00 00 00 40 00 00:15:20.551 READ FPDMA QUEUED 42 00 00 00 02 00 00 02 bf a4 15 40 00 00:15:17.965 READ VERIFY SECTOR(S) EXT 42 00 00 00 02 00 00 02 bf a4 15 40 00 00:15:15.379 READ VERIFY SECTOR(S) EXT Error 193 [0] occurred at disk power-on lifetime: 1564 hours (65 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 02 bf a4 15 40 00 Error: UNC at LBA = 0x02bfa415 = 46113813 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 02 00 00 02 bf a4 15 40 00 00:15:20.551 READ VERIFY SECTOR(S) EXT 60 00 01 00 f0 00 00 00 00 00 00 40 00 00:15:20.551 READ FPDMA QUEUED 42 00 00 00 02 00 00 02 bf a4 15 40 00 00:15:17.965 READ VERIFY SECTOR(S) EXT 42 00 00 00 02 00 00 02 bf a4 15 40 00 00:15:15.379 READ VERIFY SECTOR(S) EXT 60 00 01 00 a0 00 00 00 00 00 00 40 00 00:15:15.379 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: 28/43 Celsius Lifetime Min/Max Temperature: 41/52 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (123) Index Estimated Time Temperature Celsius 124 2016-04-07 09:46 41 ********************** ... ..( 4 skipped). .. ********************** 1 2016-04-07 09:51 41 ********************** 2 2016-04-07 09:52 ? - 3 2016-04-07 09:53 28 ********* 4 2016-04-07 09:54 28 ********* 5 2016-04-07 09:55 30 *********** 6 2016-04-07 09:56 30 *********** 7 2016-04-07 09:57 30 *********** 8 2016-04-07 09:58 31 ************ 9 2016-04-07 09:59 31 ************ 10 2016-04-07 10:00 32 ************* 11 2016-04-07 10:01 33 ************** 12 2016-04-07 10:02 34 *************** 13 2016-04-07 10:03 33 ************** 14 2016-04-07 10:04 34 *************** 15 2016-04-07 10:05 34 *************** 16 2016-04-07 10:06 34 *************** 17 2016-04-07 10:07 35 **************** 18 2016-04-07 10:08 35 **************** 19 2016-04-07 10:09 35 **************** 20 2016-04-07 10:10 36 ***************** 21 2016-04-07 10:11 36 ***************** 22 2016-04-07 10:12 36 ***************** 23 2016-04-07 10:13 37 ****************** ... ..( 3 skipped). .. ****************** 27 2016-04-07 10:17 37 ****************** 28 2016-04-07 10:18 38 ******************* ... ..( 5 skipped). .. ******************* 34 2016-04-07 10:24 38 ******************* 35 2016-04-07 10:25 39 ******************** 36 2016-04-07 10:26 39 ******************** 37 2016-04-07 10:27 40 ********************* ... ..( 2 skipped). .. ********************* 40 2016-04-07 10:30 40 ********************* 41 2016-04-07 10:31 41 ********************** ... ..( 7 skipped). .. ********************** 49 2016-04-07 10:39 41 ********************** 50 2016-04-07 10:40 42 *********************** 51 2016-04-07 10:41 42 *********************** 52 2016-04-07 10:42 41 ********************** 53 2016-04-07 10:43 41 ********************** 54 2016-04-07 10:44 41 ********************** 55 2016-04-07 10:45 ? - 56 2016-04-07 10:46 41 ********************** ... ..( 9 skipped). .. ********************** 66 2016-04-07 10:56 41 ********************** 67 2016-04-07 10:57 42 *********************** 68 2016-04-07 10:58 42 *********************** 69 2016-04-07 10:59 41 ********************** ... ..( 22 skipped). .. ********************** 92 2016-04-07 11:22 41 ********************** 93 2016-04-07 11:23 42 *********************** 94 2016-04-07 11:24 42 *********************** 95 2016-04-07 11:25 43 ************************ 96 2016-04-07 11:26 43 ************************ 97 2016-04-07 11:27 42 *********************** ... ..( 15 skipped). .. *********************** 113 2016-04-07 11:43 42 *********************** 114 2016-04-07 11:44 41 ********************** 115 2016-04-07 11:45 41 ********************** 116 2016-04-07 11:46 42 *********************** 117 2016-04-07 11:47 42 *********************** 118 2016-04-07 11:48 42 *********************** 119 2016-04-07 11:49 41 ********************** 120 2016-04-07 11:50 42 *********************** 121 2016-04-07 11:51 42 *********************** 122 2016-04-07 11:52 42 *********************** 123 2016-04-07 11:53 41 ********************** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 7158 Vendor specific