/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-48-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 850 EVO 500GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: EMT02B6Q User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Oct 13 13:15:59 2020 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 265) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 099 099 000 - 4360 12 Power_Cycle_Count -O--CK 098 098 000 - 1199 177 Wear_Leveling_Count PO--C- 099 099 000 - 7 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 099 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 060 047 000 - 40 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 099 099 000 - 17 235 POR_Recovery_Count -O--C- 099 099 000 - 273 241 Total_LBAs_Written -O--CK 099 099 000 - 7302847936 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Interrupted (host reset) 90% 768 - # 2 Short offline Completed without error 00% 455 - # 3 Short offline Completed without error 00% 430 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 32/39 Celsius Lifetime Min/Max Temperature: 25/52 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (95) Index Estimated Time Temperature Celsius 96 2020-10-12 16:00 38 ******************* ... ..( 3 skipped). .. ******************* 100 2020-10-12 16:40 38 ******************* 101 2020-10-12 16:50 41 ********************** 102 2020-10-12 17:00 43 ************************ 103 2020-10-12 17:10 43 ************************ 104 2020-10-12 17:20 44 ************************* ... ..( 6 skipped). .. ************************* 111 2020-10-12 18:30 44 ************************* 112 2020-10-12 18:40 45 ************************** 113 2020-10-12 18:50 44 ************************* 114 2020-10-12 19:00 41 ********************** 115 2020-10-12 19:10 40 ********************* 116 2020-10-12 19:20 40 ********************* 117 2020-10-12 19:30 38 ******************* ... ..( 3 skipped). .. ******************* 121 2020-10-12 20:10 38 ******************* 122 2020-10-12 20:20 37 ****************** 123 2020-10-12 20:30 38 ******************* 124 2020-10-12 20:40 37 ****************** ... ..( 7 skipped). .. ****************** 4 2020-10-12 22:00 37 ****************** 5 2020-10-12 22:10 36 ***************** 6 2020-10-12 22:20 37 ****************** 7 2020-10-12 22:30 36 ***************** 8 2020-10-12 22:40 37 ****************** 9 2020-10-12 22:50 37 ****************** 10 2020-10-12 23:00 36 ***************** 11 2020-10-12 23:10 37 ****************** 12 2020-10-12 23:20 37 ****************** 13 2020-10-12 23:30 36 ***************** 14 2020-10-12 23:40 36 ***************** 15 2020-10-12 23:50 37 ****************** 16 2020-10-13 00:00 37 ****************** 17 2020-10-13 00:10 36 ***************** ... ..( 5 skipped). .. ***************** 23 2020-10-13 01:10 36 ***************** 24 2020-10-13 01:20 37 ****************** 25 2020-10-13 01:30 36 ***************** 26 2020-10-13 01:40 37 ****************** 27 2020-10-13 01:50 37 ****************** 28 2020-10-13 02:00 38 ******************* 29 2020-10-13 02:10 ? - 30 2020-10-13 02:20 33 ************** 31 2020-10-13 02:30 35 **************** 32 2020-10-13 02:40 36 ***************** 33 2020-10-13 02:50 37 ****************** 34 2020-10-13 03:00 37 ****************** 35 2020-10-13 03:10 37 ****************** 36 2020-10-13 03:20 38 ******************* 37 2020-10-13 03:30 38 ******************* 38 2020-10-13 03:40 38 ******************* 39 2020-10-13 03:50 37 ****************** ... ..( 4 skipped). .. ****************** 44 2020-10-13 04:40 37 ****************** 45 2020-10-13 04:50 36 ***************** 46 2020-10-13 05:00 37 ****************** 47 2020-10-13 05:10 38 ******************* 48 2020-10-13 05:20 38 ******************* 49 2020-10-13 05:30 38 ******************* 50 2020-10-13 05:40 37 ****************** 51 2020-10-13 05:50 38 ******************* ... ..( 15 skipped). .. ******************* 67 2020-10-13 08:30 38 ******************* 68 2020-10-13 08:40 37 ****************** ... ..( 6 skipped). .. ****************** 75 2020-10-13 09:50 37 ****************** 76 2020-10-13 10:00 36 ***************** ... ..( 7 skipped). .. ***************** 84 2020-10-13 11:20 36 ***************** 85 2020-10-13 11:30 ? - 86 2020-10-13 11:40 32 ************* 87 2020-10-13 11:50 36 ***************** 88 2020-10-13 12:00 38 ******************* 89 2020-10-13 12:10 39 ******************** ... ..( 4 skipped). .. ******************** 94 2020-10-13 13:00 39 ******************** 95 2020-10-13 13:10 38 ******************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 8 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 8 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-48-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD3200BEVT-11ZCT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 11.01A11 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Tue Oct 13 13:15:59 2020 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 9960) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 118) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 1 3 Spin_Up_Time POS--K 185 184 021 - 1741 4 Start_Stop_Count -O--CK 098 098 000 - 2987 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 072 072 000 - 20833 10 Spin_Retry_Count PO--CK 100 099 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2258 192 Power-Off_Retract_Count -O--CK 200 200 000 - 120 193 Load_Cycle_Count -O--CK 077 077 000 - 369122 194 Temperature_Celsius -O---K 108 089 000 - 39 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate P--R-- 100 253 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 29 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 29 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 70 61 06 35 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 70 08 00 58 06 70 0b 35 60 00 00 00 00:00:02.064 NOP [Reserved subcommand] [OBS-ACS-2] 23 70 60 06 35 00 68 00 b0 10 00 00 00 00:06:46.896 READ LONG (w/o retry) [OBS-4] 00 58 10 00 50 06 70 23 35 61 00 00 00 00:00:41.568 NOP [Reserved subcommand] [OBS-ACS-2] Error 28 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 30 60 06 27 00 00 00 00 00 00 00 09 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 f8 08 00 c0 06 1e 09 27 60 00 00 00 00:00:47.120 NOP [Reserved subcommand] [OBS-ACS-2] 00 0e 60 06 27 00 f0 00 ba 40 00 00 00 00:06:43.215 NOP [Reserved subcommand] [OBS-ACS-2] 00 e0 08 00 18 06 02 00 27 60 00 00 00 00:01:02.184 NOP [Reserved subcommand] [OBS-ACS-2] Error 27 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 35 61 06 18 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 48 08 00 80 06 35 00 18 61 00 00 00 00:00:43.056 NOP [Reserved subcommand] [OBS-ACS-2] 00 35 61 06 18 00 30 00 28 08 00 00 00 00:06:39.413 NOP [Reserved subcommand] [OBS-ACS-2] 00 50 17 00 58 06 35 00 18 60 00 00 00 00:00:24.664 NOP [Reserved subcommand] [OBS-ACS-2] Error 26 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 bf 60 06 09 00 00 00 00 00 00 00 23 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 48 08 00 d0 06 bf 0b 09 60 00 00 00 00:00:45.200 NOP [Reserved subcommand] [OBS-ACS-2] 0b bf 60 06 09 00 40 00 e0 08 00 00 0b 00:06:35.711 REQUEST SENSE DATA EXT 00 30 68 00 58 06 bf 0b 09 60 00 00 00 00:00:30.776 NOP [Reserved subcommand] [OBS-ACS-2] Error 25 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 90 61 05 fc 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 58 08 00 08 05 90 00 fc 61 00 00 00 00:00:51.280 NOP [Reserved subcommand] [OBS-ACS-2] 00 8f 61 05 fc 00 50 00 b0 08 00 00 00 00:06:32.336 NOP [Reserved subcommand] [OBS-ACS-2] 00 58 08 00 70 05 8f 00 fc 61 00 00 00 00:00:04.136 NOP [Reserved subcommand] [OBS-ACS-2] Error 24 [23] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 c5 61 05 ee 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 d4 00 80 05 c3 00 ee 61 00 00 00 00:00:02.088 NOP [Reserved subcommand] [OBS-ACS-2] 23 c3 61 05 ee 00 88 00 b0 10 00 00 03 00:06:28.803 READ LONG (w/o retry) [OBS-4] 00 30 08 00 a0 05 c3 15 ee 60 00 00 00 00:00:12.344 NOP [Reserved subcommand] [OBS-ACS-2] Error 23 [22] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 fb 61 05 e0 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 48 08 00 00 05 fb 00 e0 61 00 00 00 00:01:03.568 NOP [Reserved subcommand] [OBS-ACS-2] 00 fa 61 05 e0 00 50 00 80 08 00 00 00 00:06:25.274 NOP [Reserved subcommand] [OBS-ACS-2] 00 58 08 00 38 05 fa 00 e0 61 00 00 00 00:01:03.560 NOP [Reserved subcommand] [OBS-ACS-2] Error 22 [21] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 ba 61 05 d3 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 28 08 00 08 05 b9 00 d3 61 00 00 00 00:00:49.192 NOP [Reserved subcommand] [OBS-ACS-2] 15 b9 60 05 d3 00 10 00 b0 10 00 00 23 00:06:21.881 RECALIBRATE [RET-4] 00 60 08 00 10 05 b9 03 d3 61 00 00 00 00:00:45.176 NOP [Reserved subcommand] [OBS-ACS-2] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 24/40 Celsius Lifetime Min/Max Temperature: 24/58 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: 1/85 Celsius Temperature History Size (Index): 128 (118) Index Estimated Time Temperature Celsius 119 2020-10-13 11:08 38 ******************* ... ..( 17 skipped). .. ******************* 9 2020-10-13 11:26 38 ******************* 10 2020-10-13 11:27 ? - 11 2020-10-13 11:28 24 ***** 12 2020-10-13 11:29 25 ****** 13 2020-10-13 11:30 27 ******** 14 2020-10-13 11:31 28 ********* 15 2020-10-13 11:32 29 ********** 16 2020-10-13 11:33 30 *********** 17 2020-10-13 11:34 31 ************ 18 2020-10-13 11:35 31 ************ 19 2020-10-13 11:36 32 ************* 20 2020-10-13 11:37 33 ************** 21 2020-10-13 11:38 33 ************** 22 2020-10-13 11:39 34 *************** 23 2020-10-13 11:40 34 *************** 24 2020-10-13 11:41 35 **************** 25 2020-10-13 11:42 35 **************** 26 2020-10-13 11:43 36 ***************** 27 2020-10-13 11:44 36 ***************** 28 2020-10-13 11:45 36 ***************** 29 2020-10-13 11:46 37 ****************** ... ..( 3 skipped). .. ****************** 33 2020-10-13 11:50 37 ****************** 34 2020-10-13 11:51 38 ******************* ... ..( 9 skipped). .. ******************* 44 2020-10-13 12:01 38 ******************* 45 2020-10-13 12:02 39 ******************** ... ..( 20 skipped). .. ******************** 66 2020-10-13 12:23 39 ******************** 67 2020-10-13 12:24 40 ********************* 68 2020-10-13 12:25 39 ******************** 69 2020-10-13 12:26 40 ********************* 70 2020-10-13 12:27 39 ******************** 71 2020-10-13 12:28 40 ********************* ... ..( 23 skipped). .. ********************* 95 2020-10-13 12:52 40 ********************* 96 2020-10-13 12:53 39 ******************** ... ..( 21 skipped). .. ******************** 118 2020-10-13 13:15 39 ******************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x8000 4 6573 Vendor specific /dev/sdc smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-48-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SandForce Driven SSDs Device Model: SanDisk SDSSDX120GG25 Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: R211 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS, ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Oct 13 13:15:59 2020 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Disabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 48) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0021) SCT Status supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 120 120 050 - 0/0 5 Retired_Block_Count PO--CK 100 100 003 - 0 9 Power_On_Hours_and_Msec -O--CK 089 089 000 - 9814h+22m+41.500s 12 Power_Cycle_Count -O--CK 097 097 000 - 3418 171 Program_Fail_Count -O--CK 000 000 000 - 0 172 Erase_Fail_Count -O--CK 000 000 000 - 0 174 Unexpect_Power_Loss_Ct ----CK 000 000 000 - 579 177 Wear_Range_Delta ------ 000 000 000 - 4 181 Program_Fail_Count -O--CK 000 000 000 - 0 182 Erase_Fail_Count -O--CK 000 000 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 039 052 000 - 39 (Min/Max 15/52) 195 ECC_Uncorr_Error_Count --SRC- 100 100 000 - 0/0 196 Reallocated_Event_Count PO--CK 100 100 003 - 0 201 Unc_Soft_Read_Err_Rate --SRC- 100 100 000 - 0/0 204 Soft_ECC_Correct_Rate --SRC- 100 100 000 - 0/0 230 Life_Curve_Status PO--C- 100 100 000 - 100 231 SSD_Life_Left PO--C- 100 100 010 - 0 233 SandForce_Internal ------ 000 000 000 - 8093 234 SandForce_Internal -O--CK 000 000 000 - 7562 241 Lifetime_Writes_GiB -O--CK 000 000 000 - 7562 242 Lifetime_Reads_GiB -O--CK 000 000 000 - 11749 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xb7 GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log not supported SMART Extended Self-test Log Version: 0 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 0 (0x0000) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 24/39 Celsius Lifetime Min/Max Temperature: 15/52 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 10 (Unknown, should be 2) Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/120 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 28509 (289) Invalid Temperature History Size or Index SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 7 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 8 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x0002 2 0 R_ERR response for data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdd smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-48-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 Device Model: ST3750640AS Serial Number: -- Firmware Version: 3.AFM User Capacity: 750,156,374,016 bytes [750 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Tue Oct 13 13:15:59 2020 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 202) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 253 006 - 0 3 Spin_Up_Time PO---- 091 091 000 - 0 4 Start_Stop_Count -O--CK 097 097 020 - 3736 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 053 050 030 - 18529310347268 9 Power_On_Hours -O--CK 039 039 000 - 53742 10 Spin_Retry_Count PO--C- 100 099 097 - 0 12 Power_Cycle_Count -O--CK 097 097 020 - 3390 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 052 034 045 Past 48 (Min/Max 26/48 #63) 194 Temperature_Celsius -O---K 048 066 000 - 48 (0 15 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 063 054 000 - 5177 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 50310 - # 2 Extended offline Aborted by host 90% 50310 - # 3 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 9 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS