/dev/sda === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F1 DT Device Model: SAMSUNG HD502IJ Serial Number: -- LU WWN Device Id: 5 0000f0 ... Firmware Version: 1AA01113 User Capacity: 500 107 862 016 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b Local Time is: Thu Apr 7 16:14:34 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 254 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7773) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 130) minutes. Conveyance self-test routine recommended polling time: ( 14) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 051 - 0 3 Spin_Up_Time POS--- 086 086 011 - 5030 4 Start_Stop_Count -O--CK 095 095 000 - 5239 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate -OSR-- 100 100 000 - 0 8 Seek_Time_Performance --S--K 100 100 000 - 9980 9 Power_On_Hours -O--CK 099 099 000 - 4486 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--C- 100 100 000 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3393 13 Read_Soft_Error_Rate -OSR-- 100 100 000 - 0 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 080 067 000 - 20 (Min/Max 20/20) 194 Temperature_Celsius -O---K 074 064 000 - 26 (Min/Max 20/26) 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 1931 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 100 100 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x40 GPL - 2 Reserved 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) No Errors Logged SMART Extended Self-test Log Version: 0 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 3417 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 26 Celsius Power Cycle Max Temperature: 26 Celsius Lifetime Max Temperature: 59 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -4/72 Celsius Min/Max Temperature Limit: -9/77 Celsius Temperature History Size (Index): 128 (18) Index Estimated Time Temperature Celsius 19 2016-04-07 14:07 25 ****** 20 2016-04-07 14:08 26 ******* ... ..( 3 skipped). .. ******* 24 2016-04-07 14:12 26 ******* 25 2016-04-07 14:13 27 ******** ... ..( 7 skipped). .. ******** 33 2016-04-07 14:21 27 ******** 34 2016-04-07 14:22 28 ********* ... ..( 24 skipped). .. ********* 59 2016-04-07 14:47 28 ********* 60 2016-04-07 14:48 29 ********** 61 2016-04-07 14:49 28 ********* ... ..( 28 skipped). .. ********* 90 2016-04-07 15:18 28 ********* 91 2016-04-07 15:19 ? - 92 2016-04-07 15:20 18 - 93 2016-04-07 15:21 19 - 94 2016-04-07 15:22 20 * 95 2016-04-07 15:23 20 * 96 2016-04-07 15:24 21 ** 97 2016-04-07 15:25 21 ** 98 2016-04-07 15:26 22 *** 99 2016-04-07 15:27 22 *** 100 2016-04-07 15:28 23 **** 101 2016-04-07 15:29 23 **** 102 2016-04-07 15:30 24 ***** 103 2016-04-07 15:31 24 ***** 104 2016-04-07 15:32 25 ****** ... ..( 2 skipped). .. ****** 107 2016-04-07 15:35 25 ****** 108 2016-04-07 15:36 26 ******* ... ..( 4 skipped). .. ******* 113 2016-04-07 15:41 26 ******* 114 2016-04-07 15:42 27 ******** ... ..( 5 skipped). .. ******** 120 2016-04-07 15:48 27 ******** 121 2016-04-07 15:49 28 ********* ... ..( 5 skipped). .. ********* 127 2016-04-07 15:55 28 ********* 0 2016-04-07 15:56 ? - 1 2016-04-07 15:57 20 * 2 2016-04-07 15:58 21 ** 3 2016-04-07 15:59 21 ** 4 2016-04-07 16:00 22 *** 5 2016-04-07 16:01 22 *** 6 2016-04-07 16:02 23 **** 7 2016-04-07 16:03 23 **** 8 2016-04-07 16:04 24 ***** 9 2016-04-07 16:05 24 ***** 10 2016-04-07 16:06 25 ****** ... ..( 2 skipped). .. ****** 13 2016-04-07 16:09 25 ****** 14 2016-04-07 16:10 26 ******* ... ..( 3 skipped). .. ******* 18 2016-04-07 16:14 26 ******* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.9 Device Model: ST3160811AS Serial Number: -- Firmware Version: 3.AAE User Capacity: 160 040 803 840 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Thu Apr 7 16:14:34 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 54) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 115 096 006 - 87646108 3 Spin_Up_Time PO---- 095 095 000 - 0 4 Start_Stop_Count -O--CK 094 094 020 - 6700 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 082 060 030 - 179088914 9 Power_On_Hours -O--CK 093 093 000 - 6354 10 Spin_Retry_Count PO--C- 100 099 097 - 0 12 Power_Cycle_Count -O--CK 094 094 020 - 6473 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 062 053 045 - 38 (Min/Max 29/38) 194 Temperature_Celsius -O---K 038 047 000 - 38 (0 18 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 063 048 000 - 82900312 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 1 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 17 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 17 [16] occurred at disk power-on lifetime: 4937 hours (205 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 5f 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 95 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 27 00 2b 58 e0 00 00:01:20.713 READ DMA EXT 25 00 00 00 80 00 00 26 00 2b d0 e0 00 00:01:20.746 READ DMA EXT 25 00 00 00 80 00 00 26 00 2b 48 e0 00 00:01:20.745 READ DMA EXT 25 00 00 00 40 00 00 26 00 2b 00 e0 00 00:01:20.745 READ DMA EXT 25 00 00 00 18 00 00 07 00 2b 48 e0 00 00:01:20.741 READ DMA EXT Error 16 [15] occurred at disk power-on lifetime: 3588 hours (149 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 00 00 00 00 00 e2 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 00 01 01 00 12 96 00 a1 6e e2 00 00:50:12.164 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 00 00 12 96 00 a1 6e e0 00 00:50:12.103 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 00 00 00 12 96 00 a1 6e e2 00 00:50:10.019 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 01 01 00 12 96 00 a1 6e e0 00 00:50:09.960 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 01 01 00 12 96 00 a1 6e e2 00 00:50:09.744 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 15 [14] occurred at disk power-on lifetime: 3588 hours (149 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 00 00 00 00 00 e2 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 00 01 01 00 12 96 00 a1 6e e2 00 00:49:59.064 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 00 00 12 96 00 a1 6e e0 00 00:49:59.063 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 00 00 00 12 96 00 a1 6e e2 00 00:50:10.019 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 01 00 12 9e 00 a1 af e0 00 00:50:09.960 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 29 00 00 00 01 00 12 9e 00 a1 af e0 00 00:50:09.744 READ MULTIPLE EXT Error 14 [13] occurred at disk power-on lifetime: 3588 hours (149 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 00 00 00 00 00 e2 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 00 01 01 00 12 96 00 a1 6e e2 00 00:40:04.018 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 00 00 12 96 00 a1 6e e0 00 00:40:20.267 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 00 00 00 12 96 00 a1 6e e2 00 00:40:20.208 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 01 01 00 12 96 00 a1 6e e0 00 00:40:19.992 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 01 01 00 12 96 00 a1 6e e2 00 00:40:19.923 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 13 [12] occurred at disk power-on lifetime: 3588 hours (149 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 00 00 00 00 00 e2 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 00 01 01 00 12 96 00 a1 6e e2 00 00:40:04.018 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 00 00 12 96 00 a1 6e e0 00 00:40:04.018 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 00 00 00 12 96 00 a1 6e e2 00 00:40:03.563 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 01 00 12 9e 00 a1 af e0 00 00:40:03.562 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 29 00 00 00 01 00 12 9e 00 a1 af e0 00 00:40:03.562 READ MULTIPLE EXT Error 12 [11] occurred at disk power-on lifetime: 3588 hours (149 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 00 00 00 00 00 e2 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 00 01 01 00 12 96 00 a1 6e e2 00 00:34:19.008 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 00 00 12 96 00 a1 6e e0 00 00:34:17.534 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 00 00 00 12 96 00 a1 6e e2 00 00:34:17.483 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 01 01 00 12 96 00 a1 6e e0 00 00:34:17.483 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 01 01 00 12 96 00 a1 6e e2 00 00:34:17.483 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 11 [10] occurred at disk power-on lifetime: 3588 hours (149 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 00 00 00 00 00 e2 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 00 01 01 00 12 96 00 a1 6e e2 00 00:34:19.008 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 00 00 12 96 00 a1 6e e0 00 00:34:17.534 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 00 00 00 12 96 00 a1 6e e2 00 00:34:17.483 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 01 00 12 9e 00 a1 af e0 00 00:34:17.483 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 29 00 00 00 01 00 12 9e 00 a1 af e0 00 00:34:17.483 READ MULTIPLE EXT Error 10 [9] occurred at disk power-on lifetime: 3588 hours (149 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 00 00 00 00 00 e2 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 00 01 01 00 12 96 00 a1 6e e2 00 00:30:20.085 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 00 00 12 96 00 a1 6e e0 00 00:30:18.191 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 00 00 00 12 96 00 a1 6e e2 00 00:30:18.140 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 01 01 00 12 96 00 a1 6e e0 00 00:30:18.139 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 01 01 00 12 96 00 a1 6e e2 00 00:30:18.139 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 5011 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 8 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS