/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA (AF) Device Model: WDC WD5000BPVT-22HXZT3 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 500 107 862 016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Dec 16 17:57:33 2017 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 96 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (11700) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 116) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 3 3 Spin_Up_Time POS--K 175 172 021 - 2250 4 Start_Stop_Count -O--CK 027 027 000 - 73120 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 066 066 000 - 25457 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 093 093 000 - 7450 191 G-Sense_Error_Rate -O--CK 001 001 000 - 2844 192 Power-Off_Retract_Count -O--CK 199 199 000 - 1280 193 Load_Cycle_Count -O--CK 001 001 000 - 3829572 194 Temperature_Celsius -O---K 115 098 000 - 32 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 1 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 120 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 120 [23] occurred at disk power-on lifetime: 1916 hours (79 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 10 b6 13 48 40 00 Error: UNC at LBA = 0x10b61348 = 280367944 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 08 00 00 10 b6 13 40 40 00 00:09:15.327 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:09:15.327 SET FEATURES [Enable write cache] 60 00 10 00 08 00 00 10 b6 13 40 40 00 00:09:12.522 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:09:12.522 SET FEATURES [Enable write cache] 60 00 10 00 08 00 00 10 b6 13 40 40 00 00:09:09.717 READ FPDMA QUEUED Error 119 [22] occurred at disk power-on lifetime: 1916 hours (79 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 10 b6 13 48 40 00 Error: UNC at LBA = 0x10b61348 = 280367944 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 08 00 00 10 b6 13 40 40 00 00:09:12.522 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:09:12.522 SET FEATURES [Enable write cache] 60 00 10 00 08 00 00 10 b6 13 40 40 00 00:09:09.717 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:09:09.717 SET FEATURES [Enable write cache] 60 00 10 00 08 00 00 10 b6 13 40 40 00 00:09:06.881 READ FPDMA QUEUED Error 118 [21] occurred at disk power-on lifetime: 1916 hours (79 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 10 b6 13 48 40 00 Error: UNC at LBA = 0x10b61348 = 280367944 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 08 00 00 10 b6 13 40 40 00 00:09:09.717 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:09:09.717 SET FEATURES [Enable write cache] 60 00 10 00 08 00 00 10 b6 13 40 40 00 00:09:06.881 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:09:06.880 SET FEATURES [Enable write cache] 60 00 10 00 08 00 00 10 b6 13 40 40 00 00:09:04.075 READ FPDMA QUEUED Error 117 [20] occurred at disk power-on lifetime: 1916 hours (79 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 10 b6 13 48 40 00 Error: UNC at LBA = 0x10b61348 = 280367944 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 08 00 00 10 b6 13 40 40 00 00:09:06.881 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:09:06.880 SET FEATURES [Enable write cache] 60 00 10 00 08 00 00 10 b6 13 40 40 00 00:09:04.075 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:09:04.075 SET FEATURES [Enable write cache] 60 00 10 00 08 00 00 10 b6 13 40 40 00 00:09:01.270 READ FPDMA QUEUED Error 116 [19] occurred at disk power-on lifetime: 1916 hours (79 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 10 b6 13 48 40 00 Error: UNC at LBA = 0x10b61348 = 280367944 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 08 00 00 10 b6 13 40 40 00 00:09:04.075 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:09:04.075 SET FEATURES [Enable write cache] 60 00 10 00 08 00 00 10 b6 13 40 40 00 00:09:01.270 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:09:01.270 SET FEATURES [Enable write cache] 60 00 10 00 08 00 00 10 b6 13 40 40 00 00:08:58.465 READ FPDMA QUEUED Error 115 [18] occurred at disk power-on lifetime: 1916 hours (79 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 10 b6 13 48 40 00 Error: UNC at LBA = 0x10b61348 = 280367944 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 08 00 00 10 b6 13 40 40 00 00:09:01.270 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:09:01.270 SET FEATURES [Enable write cache] 60 00 10 00 08 00 00 10 b6 13 40 40 00 00:08:58.465 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:08:58.465 SET FEATURES [Enable write cache] 60 00 10 00 20 00 00 10 b6 13 40 40 00 00:08:55.644 READ FPDMA QUEUED Error 114 [17] occurred at disk power-on lifetime: 1916 hours (79 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 10 b6 13 48 40 00 Error: UNC at LBA = 0x10b61348 = 280367944 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 08 00 00 10 b6 13 40 40 00 00:08:58.465 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:08:58.465 SET FEATURES [Enable write cache] 60 00 10 00 20 00 00 10 b6 13 40 40 00 00:08:55.644 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:08:55.644 SET FEATURES [Enable write cache] 60 00 f8 00 20 00 00 10 b6 65 40 40 00 00:08:52.870 READ FPDMA QUEUED Error 113 [16] occurred at disk power-on lifetime: 1916 hours (79 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 10 b6 13 48 40 00 Error: UNC at LBA = 0x10b61348 = 280367944 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 20 00 00 10 b6 13 40 40 00 00:08:55.644 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:08:55.644 SET FEATURES [Enable write cache] 60 00 f8 00 20 00 00 10 b6 65 40 40 00 00:08:52.870 READ FPDMA QUEUED 60 01 00 00 18 00 00 10 b6 64 40 40 00 00:08:52.868 READ FPDMA QUEUED 60 01 00 00 10 00 00 10 b6 63 40 40 00 00:08:52.867 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 20529 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 22/40 Celsius Lifetime Min/Max Temperature: 0/49 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (7) Index Estimated Time Temperature Celsius 8 2017-12-16 15:50 35 **************** ... ..( 18 skipped). .. **************** 27 2017-12-16 16:09 35 **************** 28 2017-12-16 16:10 ? - 29 2017-12-16 16:11 35 **************** 30 2017-12-16 16:12 35 **************** 31 2017-12-16 16:13 ? - 32 2017-12-16 16:14 35 **************** 33 2017-12-16 16:15 35 **************** 34 2017-12-16 16:16 ? - 35 2017-12-16 16:17 35 **************** 36 2017-12-16 16:18 35 **************** 37 2017-12-16 16:19 35 **************** 38 2017-12-16 16:20 ? - 39 2017-12-16 16:21 35 **************** 40 2017-12-16 16:22 35 **************** 41 2017-12-16 16:23 ? - 42 2017-12-16 16:24 35 **************** ... ..( 2 skipped). .. **************** 45 2017-12-16 16:27 35 **************** 46 2017-12-16 16:28 ? - 47 2017-12-16 16:29 35 **************** 48 2017-12-16 16:30 35 **************** 49 2017-12-16 16:31 ? - 50 2017-12-16 16:32 35 **************** 51 2017-12-16 16:33 35 **************** 52 2017-12-16 16:34 ? - 53 2017-12-16 16:35 35 **************** 54 2017-12-16 16:36 35 **************** 55 2017-12-16 16:37 ? - 56 2017-12-16 16:38 35 **************** 57 2017-12-16 16:39 35 **************** 58 2017-12-16 16:40 ? - 59 2017-12-16 16:41 35 **************** 60 2017-12-16 16:42 35 **************** 61 2017-12-16 16:43 ? - 62 2017-12-16 16:44 35 **************** 63 2017-12-16 16:45 35 **************** 64 2017-12-16 16:46 ? - 65 2017-12-16 16:47 35 **************** 66 2017-12-16 16:48 35 **************** 67 2017-12-16 16:49 ? - 68 2017-12-16 16:50 34 *************** 69 2017-12-16 16:51 34 *************** 70 2017-12-16 16:52 ? - 71 2017-12-16 16:53 34 *************** 72 2017-12-16 16:54 ? - 73 2017-12-16 16:55 34 *************** 74 2017-12-16 16:56 34 *************** 75 2017-12-16 16:57 34 *************** 76 2017-12-16 16:58 ? - 77 2017-12-16 16:59 34 *************** 78 2017-12-16 17:00 34 *************** 79 2017-12-16 17:01 ? - 80 2017-12-16 17:02 34 *************** ... ..( 2 skipped). .. *************** 83 2017-12-16 17:05 34 *************** 84 2017-12-16 17:06 ? - 85 2017-12-16 17:07 34 *************** 86 2017-12-16 17:08 34 *************** 87 2017-12-16 17:09 34 *************** 88 2017-12-16 17:10 ? - 89 2017-12-16 17:11 34 *************** 90 2017-12-16 17:12 34 *************** 91 2017-12-16 17:13 ? - 92 2017-12-16 17:14 34 *************** 93 2017-12-16 17:15 34 *************** 94 2017-12-16 17:16 ? - 95 2017-12-16 17:17 34 *************** 96 2017-12-16 17:18 ? - 97 2017-12-16 17:19 34 *************** ... ..( 14 skipped). .. *************** 112 2017-12-16 17:34 34 *************** 113 2017-12-16 17:35 35 **************** ... ..( 5 skipped). .. **************** 119 2017-12-16 17:41 35 **************** 120 2017-12-16 17:42 34 *************** ... ..( 2 skipped). .. *************** 123 2017-12-16 17:45 34 *************** 124 2017-12-16 17:46 33 ************** ... ..( 3 skipped). .. ************** 0 2017-12-16 17:50 33 ************** 1 2017-12-16 17:51 32 ************* ... ..( 3 skipped). .. ************* 5 2017-12-16 17:55 32 ************* 6 2017-12-16 17:56 ? - 7 2017-12-16 17:57 32 ************* SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 55270 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 22 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 45555 Vendor specific