/dev/sda === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.9 Device Model: ST3808110AS Serial Number: -- Firmware Version: 3.AAD User Capacity: 80 025 280 000 bytes [80,0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Sun Apr 5 14:19:03 2015 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 27) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 115 091 006 - 96224844 3 Spin_Up_Time PO---- 100 099 000 - 0 4 Start_Stop_Count -O--CK 098 098 020 - 2397 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 082 060 030 - 187198536 9 Power_On_Hours -O--CK 093 093 000 - 6601 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 4405 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 058 048 045 - 42 (Min/Max 40/42) 194 Temperature_Celsius -O---K 042 052 000 - 42 (0 18 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 066 045 000 - 145321006 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 035 000 - 3176 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 12 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 12 [11] occurred at disk power-on lifetime: 4806 hours (200 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 1f 00 00 00 00 00 00 e7 00 Error: ICRC, ABRT 31 sectors at LBA = 0x07000000 = 117440512 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 01 00 00 07 4d 00 f3 4d e7 00 01:53:12.712 READ DMA c8 00 00 01 00 00 07 4c 00 f3 4d e7 00 01:53:12.712 READ DMA ca 00 00 00 08 00 00 61 00 04 35 e0 00 01:53:12.711 WRITE DMA ca 00 00 00 08 00 00 df 00 4e 8d e0 00 01:53:12.691 WRITE DMA ca 00 00 00 10 00 00 5f 00 04 f5 e0 00 01:53:13.541 WRITE DMA Error 11 [10] occurred at disk power-on lifetime: 4385 hours (182 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 9f 00 00 00 00 00 00 e8 00 Error: ICRC, ABRT 159 sectors at LBA = 0x08000000 = 134217728 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 01 00 00 08 ac 00 4f 90 e8 00 00:13:54.884 READ DMA c8 00 00 01 00 00 08 ab 00 4f 90 e8 00 00:13:54.882 READ DMA c8 00 00 01 00 00 08 aa 00 4f 90 e8 00 00:13:54.866 READ DMA c8 00 00 01 00 00 08 a9 00 4f 90 e8 00 00:13:54.866 READ DMA c8 00 00 01 00 00 08 a8 00 4f 90 e8 00 00:13:55.849 READ DMA Error 10 [9] occurred at disk power-on lifetime: 4385 hours (182 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 7f 00 00 00 00 00 00 e8 00 Error: ICRC, ABRT 127 sectors at LBA = 0x08000000 = 134217728 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 01 00 00 08 a4 00 4f 90 e8 00 00:13:54.884 READ DMA c8 00 00 01 00 00 08 a3 00 4f 90 e8 00 00:13:54.882 READ DMA c8 00 00 01 00 00 08 a2 00 4f 90 e8 00 00:13:54.866 READ DMA c8 00 00 01 00 00 08 a1 00 4f 90 e8 00 00:13:54.866 READ DMA c8 00 00 01 00 00 08 a0 00 4f 90 e8 00 00:13:54.866 READ DMA Error 9 [8] occurred at disk power-on lifetime: 4385 hours (182 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 0f 00 00 00 00 00 00 e8 00 Error: ICRC, ABRT 15 sectors at LBA = 0x08000000 = 134217728 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 01 00 00 08 a3 00 4f 90 e8 00 00:13:54.884 READ DMA c8 00 00 01 00 00 08 a2 00 4f 90 e8 00 00:13:54.882 READ DMA c8 00 00 01 00 00 08 a1 00 4f 90 e8 00 00:13:54.866 READ DMA c8 00 00 01 00 00 08 a0 00 4f 90 e8 00 00:13:54.866 READ DMA c8 00 00 01 00 00 08 9f 00 4f 90 e8 00 00:13:54.866 READ DMA Error 8 [7] occurred at disk power-on lifetime: 4385 hours (182 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 cf 00 00 00 00 00 00 e8 00 Error: ICRC, ABRT 207 sectors at LBA = 0x08000000 = 134217728 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 01 00 00 08 8a 00 4f 90 e8 00 00:13:53.652 READ DMA c8 00 00 01 00 00 08 89 00 4f 90 e8 00 00:13:53.649 READ DMA c8 00 00 01 00 00 08 88 00 4f 90 e8 00 00:13:53.624 READ DMA c8 00 00 01 00 00 08 87 00 4f 90 e8 00 00:13:53.624 READ DMA c8 00 00 01 00 00 08 86 00 4f 90 e8 00 00:13:53.624 READ DMA Error 7 [6] occurred at disk power-on lifetime: 4385 hours (182 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 bf 00 00 00 00 00 00 e8 00 Error: ICRC, ABRT 191 sectors at LBA = 0x08000000 = 134217728 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 01 00 00 08 89 00 4f 90 e8 00 00:13:53.652 READ DMA c8 00 00 01 00 00 08 88 00 4f 90 e8 00 00:13:53.649 READ DMA c8 00 00 01 00 00 08 87 00 4f 90 e8 00 00:13:53.624 READ DMA c8 00 00 01 00 00 08 86 00 4f 90 e8 00 00:13:53.624 READ DMA c8 00 00 01 00 00 08 85 00 4f 90 e8 00 00:13:53.624 READ DMA Error 6 [5] occurred at disk power-on lifetime: 3595 hours (149 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 e0 00 Error: ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 29 00 d0 00 80 00 00 ff 00 2b 47 e0 00 00:08:13.703 READ MULTIPLE EXT b0 00 d0 01 00 00 02 17 00 fd 0f a0 00 00:08:13.703 SMART READ DATA e5 00 00 01 00 00 ff ff 00 ff ff a0 00 00:08:26.005 CHECK POWER MODE c6 00 00 00 10 00 ff ff 00 ff ff a0 00 00:08:25.973 SET MULTIPLE MODE ef 00 03 00 0c 00 ff ff 00 ff ff a0 00 00:08:25.973 SET FEATURES [Set transfer mode] Error 5 [4] occurred at disk power-on lifetime: 3595 hours (149 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 e0 00 Error: ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 29 00 00 00 3d 00 00 4a 00 be 37 e0 00 00:07:37.079 READ MULTIPLE EXT 39 00 00 00 01 00 01 27 00 65 d8 e0 00 00:07:37.079 WRITE MULTIPLE EXT 29 00 00 00 08 00 00 3e 00 e4 8f e0 00 00:07:37.078 READ MULTIPLE EXT 29 00 00 00 01 00 00 00 00 00 00 e0 00 00:07:25.111 READ MULTIPLE EXT e5 00 00 01 00 00 ff ff 00 ff ff a0 00 00:07:25.098 CHECK POWER MODE SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdb === START OF INFORMATION SECTION === Vendor: /1:0:0:0 Product: Compliance: SPC-5 User Capacity: 600 332 565 813 390 450 bytes [600 PB] Logical block size: 774843950 bytes >> Terminate command early due to bad response to IEC mode page A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options. /dev/sdc === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus Device Model: ST380817AS Serial Number: -- Firmware Version: 3.42 User Capacity: 80 025 280 000 bytes [80,0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-6 T13/1410D revision 2 Local Time is: Sun Apr 5 14:19:03 2015 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 47) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 055 041 006 - 222670829 3 Spin_Up_Time PO---- 099 098 000 - 0 4 Start_Stop_Count -O--CK 096 096 020 - 4256 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 087 060 030 - 579333849 9 Power_On_Hours -O--CK 089 089 000 - 10019 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 4648 194 Temperature_Celsius -O---K 039 050 000 - 39 (0 14 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 055 041 000 - 222670829 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 001 000 - 862 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23552 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) not supported