/dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.14.2-desktop-3omv2590] (OpenMandriva Lx 7.4-1) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: CT500BX500SSD1 Serial Number: -- LU WWN Device Id: 5 00a075 ... Firmware Version: M6CR061 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: Not in smartctl database ATA Version is: ACS-3 T13/2161-D revision 4 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri May 2 02:29:21 2025 -05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 000 - 0 5 Reallocated_Sector_Ct -O--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 8449 12 Power_Cycle_Count -O--CK 100 100 000 - 3857 171 Unknown_Attribute -O--CK 100 100 000 - 0 172 Unknown_Attribute -O--CK 100 100 000 - 0 173 Unknown_Attribute -O--CK 097 097 000 - 34 174 Unknown_Attribute -O--CK 100 100 000 - 1166 180 Unused_Rsvd_Blk_Cnt_Tot PO--CK 100 100 000 - 41 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 067 057 000 - 33 (Min/Max 18/43) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 202 Unknown_SSD_Attribute ----CK 097 097 001 - 3 206 Unknown_SSD_Attribute -OSR-- 100 100 000 - 0 210 Unknown_Attribute -O--CK 100 100 000 - 0 246 Unknown_Attribute -O--CK 100 100 000 - 18510929407 247 Unknown_Attribute -O--CK 100 100 000 - 578466543 248 Unknown_Attribute -O--CK 100 100 000 - 1465829568 249 Unknown_Attribute -O--CK 100 100 000 - 0 251 Unknown_Attribute -O--CK 100 100 000 - 1062872635 252 Unknown_Attribute -O--CK 100 100 000 - 10 253 Unknown_Attribute -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 88 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log (GP Log 0x03) not supported Read SMART Error Log failed: scsi error badly formed scsi parameters SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Aborted by host 90% 6823 - # 2 Short offline Aborted by host 90% 6823 - Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x000a 4 22 Device-to-host register FISes sent due to a COMRESET /dev/sdb smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.14.2-desktop-3omv2590] (OpenMandriva Lx 7.4-1) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Black Device Model: WDC WD3200BEKT-60PVMT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 2.5 inches Device is: In smartctl database ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri May 2 02:29:21 2025 -05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 25) The self-test routine was aborted by the host. Total time to complete Offline data collection: ( 6060) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 63) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 157 138 021 - 1141 4 Start_Stop_Count -O--CK 093 093 000 - 7575 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-K 100 253 051 - 0 9 Power_On_Hours -O--CK 064 064 000 - 26836 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 095 095 000 - 5505 183 Runtime_Bad_Block -O--CK 099 099 000 - 1 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 099 000 - 1 188 Command_Timeout -O--CK 100 091 000 - 38655295499 190 Airflow_Temperature_Cel -O---K 069 044 040 - 31 (Min/Max 30/33) 191 G-Sense_Error_Rate -O--CK 001 001 000 - 1185 192 Power-Off_Retract_Count -O--CK 200 200 000 - 102 193 Load_Cycle_Count -O--CK 148 148 000 - 157839 194 Temperature_Celsius -O---K 112 087 000 - 31 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate P--R-- 100 253 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 10 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 10 [9] occurred at disk power-on lifetime: 4822 hours (200 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 f7 df 38 a7 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 00 04:22:25.897 FLUSH CACHE EXT 61 00 08 00 a0 00 00 00 62 73 18 40 00 04:22:25.897 WRITE FPDMA QUEUED 61 00 01 00 98 00 00 00 7a 4c 38 40 00 04:22:25.897 WRITE FPDMA QUEUED 61 00 08 00 90 00 00 00 5b bd 70 40 00 04:22:25.897 WRITE FPDMA QUEUED 61 00 08 00 88 00 00 00 62 71 e0 40 00 04:22:25.896 WRITE FPDMA QUEUED Error 9 [8] occurred at disk power-on lifetime: 4822 hours (200 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 f7 df 38 a7 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 00 04:22:17.179 FLUSH CACHE EXT 61 00 08 00 20 00 00 00 61 ee e8 40 00 04:22:17.179 WRITE FPDMA QUEUED 61 00 08 00 18 00 00 00 5b bd 68 40 00 04:22:17.179 WRITE FPDMA QUEUED 61 00 08 00 10 00 00 00 5b bd 80 40 00 04:22:17.178 WRITE FPDMA QUEUED 61 00 08 00 08 00 00 00 61 ec 98 40 00 04:22:17.178 WRITE FPDMA QUEUED Error 8 [7] occurred at disk power-on lifetime: 4822 hours (200 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 f7 df 38 a7 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 00 04:22:08.017 FLUSH CACHE EXT 61 00 08 00 d8 00 00 00 5b bd 78 40 00 04:22:08.016 WRITE FPDMA QUEUED 61 00 10 00 d0 00 00 03 f2 4b d8 40 00 04:22:08.015 WRITE FPDMA QUEUED 61 00 08 00 c8 00 00 00 5f bd 68 40 00 04:22:07.662 WRITE FPDMA QUEUED 61 00 08 00 c0 00 00 00 5f c2 90 40 00 04:22:07.661 WRITE FPDMA QUEUED Error 7 [6] occurred at disk power-on lifetime: 4822 hours (200 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 f7 df 38 a7 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 00 04:21:59.038 FLUSH CACHE EXT 61 00 08 00 f0 00 00 00 02 78 18 40 00 04:21:59.038 WRITE FPDMA QUEUED 61 00 10 00 e8 00 00 00 00 75 e0 40 00 04:21:59.038 WRITE FPDMA QUEUED 61 00 20 00 e0 00 00 00 5b d5 28 40 00 04:21:59.037 WRITE FPDMA QUEUED 61 00 08 00 d8 00 00 00 00 2a b8 40 00 04:21:59.037 WRITE FPDMA QUEUED Error 6 [5] occurred at disk power-on lifetime: 4822 hours (200 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 00 00 00 40 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 d8 00 00 00 00 00 00 40 00 04:21:40.710 READ FPDMA QUEUED 60 00 01 00 d0 00 00 00 2e 2d 92 40 00 04:21:40.650 READ FPDMA QUEUED 60 00 01 00 c8 00 00 00 2e 2d 92 40 00 04:21:40.650 READ FPDMA QUEUED 60 00 01 00 c0 00 00 00 2e 2d 92 40 00 04:21:40.650 READ FPDMA QUEUED 60 00 01 00 b8 00 00 00 2e 2d 92 40 00 04:21:40.649 READ FPDMA QUEUED Error 5 [4] occurred at disk power-on lifetime: 4822 hours (200 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 f7 df 38 a7 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 00 03:34:02.270 FLUSH CACHE EXT 61 00 08 00 10 00 00 00 5b bd 80 40 00 03:34:02.269 WRITE FPDMA QUEUED 61 00 08 00 08 00 00 00 5b bd 68 40 00 03:34:02.269 WRITE FPDMA QUEUED 61 00 03 00 f8 00 00 00 0b ae 98 40 00 03:34:02.269 WRITE FPDMA QUEUED 61 00 40 00 f0 00 00 00 3a 7a c8 40 00 03:34:02.269 WRITE FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 4822 hours (200 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 f7 df 38 a7 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 00 03:33:52.514 FLUSH CACHE EXT 61 00 08 00 a8 00 00 00 61 e2 f8 40 00 03:33:52.514 WRITE FPDMA QUEUED 61 00 08 00 a0 00 00 00 5b bd 80 40 00 03:33:52.514 WRITE FPDMA QUEUED 61 00 08 00 98 00 00 00 61 de 20 40 00 03:33:52.514 WRITE FPDMA QUEUED 61 00 08 00 90 00 00 04 00 71 00 40 00 03:33:52.513 WRITE FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 4819 hours (200 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 f7 df 38 a7 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 00 01:23:19.521 FLUSH CACHE EXT 61 00 08 00 38 00 00 00 5b bd 78 40 00 01:23:19.520 WRITE FPDMA QUEUED e1 00 44 00 00 00 00 00 55 4e 4c e0 00 01:23:19.384 IDLE IMMEDIATE e1 00 44 00 00 00 00 00 55 4e 4c e0 00 01:23:19.379 IDLE IMMEDIATE 61 00 10 00 28 00 00 00 5c b6 e8 40 00 01:23:19.378 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Aborted by host 90% 24951 - # 2 Short offline Interrupted (host reset) 90% 19343 - # 3 Short offline Completed without error 00% 13338 - # 4 Short offline Completed without error 00% 13320 - # 5 Short offline Completed without error 00% 3659 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 30/33 Celsius Lifetime Min/Max Temperature: 0/57 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (90) Index Estimated Time Temperature Celsius 91 2025-05-02 00:22 31 ************ ... ..( 48 skipped). .. ************ 12 2025-05-02 01:11 31 ************ 13 2025-05-02 01:12 30 *********** ... ..( 5 skipped). .. *********** 19 2025-05-02 01:18 30 *********** 20 2025-05-02 01:19 31 ************ ... ..( 13 skipped). .. ************ 34 2025-05-02 01:33 31 ************ 35 2025-05-02 01:34 30 *********** ... ..( 12 skipped). .. *********** 48 2025-05-02 01:47 30 *********** 49 2025-05-02 01:48 31 ************ ... ..( 23 skipped). .. ************ 73 2025-05-02 02:12 31 ************ 74 2025-05-02 02:13 32 ************* 75 2025-05-02 02:14 32 ************* 76 2025-05-02 02:15 31 ************ 77 2025-05-02 02:16 32 ************* ... ..( 6 skipped). .. ************* 84 2025-05-02 02:23 32 ************* 85 2025-05-02 02:24 31 ************ 86 2025-05-02 02:25 32 ************* 87 2025-05-02 02:26 31 ************ 88 2025-05-02 02:27 32 ************* 89 2025-05-02 02:28 32 ************* 90 2025-05-02 02:29 31 ************ SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 10 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 16359 Vendor specific