/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-47-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Momentus 5400.6 Device Model: ST9500325AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0001SDM1 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue Sep 15 22:18:57 2020 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 142) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 117 084 006 - 164248160 3 Spin_Up_Time PO---- 099 098 000 - 0 4 Start_Stop_Count -O--CK 096 096 020 - 4257 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 1 7 Seek_Error_Rate POSR-- 080 060 030 - 4409417913 9 Power_On_Hours -O--CK 078 078 000 - 19372 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 097 037 020 - 3185 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 9143 188 Command_Timeout -O--CK 100 096 000 - 290 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 063 043 045 Past 37 (0 1 38 21 0) 191 G-Sense_Error_Rate -O--CK 098 098 000 - 5593 192 Power-Off_Retract_Count -O--CK 100 100 000 - 292 193 Load_Cycle_Count -O--CK 054 054 000 - 93064 194 Temperature_Celsius -O---K 037 057 000 - 37 195 Hardware_ECC_Recovered -O-RC- 047 044 000 - 164248160 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 254 Free_Fall_Sensor -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 10501 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 10501 [0] occurred at disk power-on lifetime: 3287 hours (136 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1d fd d5 94 00 00 Error: UNC at LBA = 0x1dfdd594 = 503174548 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 1d fd d5 91 40 00 01:04:25.096 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 01:04:25.074 SET FEATURES [Enable write cache] 00 00 00 00 00 00 00 00 00 00 00 00 ff 01:04:24.988 NOP [Abort queued commands] 60 00 00 00 08 00 00 1d fd d5 91 40 00 01:04:22.652 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 01:04:22.625 SET FEATURES [Enable write cache] Error 10500 [19] occurred at disk power-on lifetime: 3287 hours (136 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1d fd d5 94 00 00 Error: UNC at LBA = 0x1dfdd594 = 503174548 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 1d fd d5 91 40 00 01:04:22.652 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 01:04:22.625 SET FEATURES [Enable write cache] 00 00 00 00 00 00 00 00 00 00 00 00 ff 01:04:22.544 NOP [Abort queued commands] 60 00 00 00 08 00 00 1d fd d5 91 40 00 01:04:20.209 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 01:04:20.191 SET FEATURES [Enable write cache] Error 10499 [18] occurred at disk power-on lifetime: 3287 hours (136 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1d fd d5 94 00 00 Error: UNC at LBA = 0x1dfdd594 = 503174548 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 1d fd d5 91 40 00 01:04:20.209 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 01:04:20.191 SET FEATURES [Enable write cache] 00 00 00 00 00 00 00 00 00 00 00 00 ff 01:04:20.112 NOP [Abort queued commands] 60 00 00 00 08 00 00 1d fd d5 91 40 00 01:04:17.766 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 01:04:17.742 SET FEATURES [Enable write cache] Error 10498 [17] occurred at disk power-on lifetime: 3287 hours (136 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1d fd d5 94 00 00 Error: UNC at LBA = 0x1dfdd594 = 503174548 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 1d fd d5 91 40 00 01:04:17.766 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 01:04:17.742 SET FEATURES [Enable write cache] 00 00 00 00 00 00 00 00 00 00 00 00 ff 01:04:17.669 NOP [Abort queued commands] 60 00 00 00 08 00 00 1d fd d5 91 40 00 01:04:15.322 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 01:04:15.278 SET FEATURES [Enable write cache] Error 10497 [16] occurred at disk power-on lifetime: 3287 hours (136 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1d fd d5 94 00 00 Error: UNC at LBA = 0x1dfdd594 = 503174548 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 1d fd d5 91 40 00 01:04:15.322 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 01:04:15.278 SET FEATURES [Enable write cache] 00 00 00 00 00 00 00 00 00 00 00 00 ff 01:04:15.226 NOP [Abort queued commands] 60 00 00 00 08 00 00 1d fd d5 91 40 00 01:04:12.890 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 01:04:12.859 SET FEATURES [Enable write cache] Error 10496 [15] occurred at disk power-on lifetime: 3287 hours (136 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1d fd d5 94 00 00 Error: UNC at LBA = 0x1dfdd594 = 503174548 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 1d fd d5 91 40 00 01:04:12.890 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 01:04:12.859 SET FEATURES [Enable write cache] 00 00 00 00 00 00 00 00 00 00 00 00 ff 01:04:12.805 NOP [Abort queued commands] 60 00 00 00 08 00 00 1d fd d5 91 40 00 01:04:10.468 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 01:04:10.425 SET FEATURES [Enable write cache] Error 10495 [14] occurred at disk power-on lifetime: 3287 hours (136 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1d fd d5 94 00 00 Error: UNC at LBA = 0x1dfdd594 = 503174548 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 1d fd d5 91 40 00 01:04:10.468 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 01:04:10.425 SET FEATURES [Enable write cache] 00 00 00 00 00 00 00 00 00 00 00 00 ff 01:04:10.372 NOP [Abort queued commands] 60 00 00 00 08 00 00 1d fd d5 91 40 00 01:04:08.036 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 01:04:08.007 SET FEATURES [Enable write cache] Error 10494 [13] occurred at disk power-on lifetime: 3287 hours (136 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1d fd d5 94 00 00 Error: UNC at LBA = 0x1dfdd594 = 503174548 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 1d fd d5 91 40 00 01:04:08.036 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 01:04:08.007 SET FEATURES [Enable write cache] 00 00 00 00 00 00 00 00 00 00 00 00 ff 01:04:07.962 NOP [Abort queued commands] 60 00 00 00 08 00 00 1d fd d5 91 40 00 01:04:05.636 READ FPDMA QUEUED 60 00 00 00 08 00 00 1d fd d5 89 40 00 01:04:05.635 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: 21/38 Celsius Lifetime Min/Max Temperature: 0/57 Celsius Under/Over Temperature Limit Count: 0/265 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (53) Index Estimated Time Temperature Celsius 54 2020-09-15 20:11 36 ***************** ... ..( 15 skipped). .. ***************** 70 2020-09-15 20:27 36 ***************** 71 2020-09-15 20:28 37 ****************** ... ..( 99 skipped). .. ****************** 43 2020-09-15 22:08 37 ****************** 44 2020-09-15 22:09 38 ******************* ... ..( 4 skipped). .. ******************* 49 2020-09-15 22:14 38 ******************* 50 2020-09-15 22:15 37 ****************** ... ..( 2 skipped). .. ****************** 53 2020-09-15 22:18 37 ****************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS