/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.1-desktop-1omv2290] (OpenMandriva Lx 7.3-2) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Phison Driven SSDs Device Model: KINGSTON SA400S37240G Serial Number: -- LU WWN Device Id: 5 0026b7 ... Firmware Version: SBFKB1D1 User Capacity: 240,057,409,536 bytes [240 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: In smartctl database ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Feb 13 11:39:50 2023 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (65535) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 6450 12 Power_Cycle_Count -O--CK 100 100 000 - 1226 148 Unknown_Attribute ------ 255 255 000 - 0 149 Unknown_Attribute ------ 255 255 000 - 0 167 Write_Protect_Mode ------ 100 100 000 - 0 168 SATA_Phy_Error_Count -O--C- 100 100 000 - 0 169 Bad_Block_Rate ------ 100 100 000 - 16 170 Bad_Blk_Ct_Erl/Lat ------ 100 100 010 - 0/11 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 MaxAvgErase_Ct ------ 100 100 000 - 88 (Average 65) 181 Program_Fail_Count -O--CK 100 100 000 - 0 182 Erase_Fail_Count ------ 255 255 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 192 Unsafe_Shutdown_Count -O--C- 100 100 000 - 151 194 Temperature_Celsius -O---K 076 066 000 - 24 (Min/Max 16/34) 196 Reallocated_Event_Count ------ 100 100 000 - 0 199 SATA_CRC_Error_Count -O--CK 100 100 000 - 0 218 CRC_Error_Count ------ 100 100 000 - 624511 231 SSD_Life_Left PO--C- 100 100 000 - 93 233 Flash_Writes_GiB PO--C- 100 100 000 - 11710 241 Lifetime_Writes_GiB -O--C- 100 100 000 - 7911 242 Lifetime_Reads_GiB -O--C- 100 100 000 - 7145 244 Average_Erase_Count ------ 100 100 000 - 65 245 Max_Erase_Count ------ 100 100 000 - 88 246 Total_Erase_Count ------ 100 100 000 - 502848 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 6 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 6 [5] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 40 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 06 00 01 00 01 00 00 00 00 00 00 40 00 00:00:00.000 DATA SET MANAGEMENT ec 00 00 00 00 00 00 00 00 00 00 40 00 00:00:00.000 IDENTIFY DEVICE ff 00 d5 00 01 00 00 00 00 00 01 00 ff 00:00:00.000 [VENDOR SPECIFIC] 61 01 00 00 20 00 00 01 01 a3 80 40 00 00:00:00.000 WRITE FPDMA QUEUED 61 00 08 00 18 00 00 00 5e f0 18 40 00 00:00:00.000 WRITE FPDMA QUEUED Error 5 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 08 00 00 15 51 36 90 40 00 Error: ICRC, ABRT 8 sectors at LBA = 0x15513690 = 357643920 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 08 00 00 15 51 36 90 40 00 00:00:00.000 WRITE DMA EXT 25 00 00 00 01 00 00 1b f2 44 ae 40 00 00:00:00.000 READ DMA EXT 40 00 00 00 01 00 00 00 00 00 00 40 00 00:00:00.000 READ VERIFY SECTOR(S) ef 00 10 00 02 00 00 00 00 00 00 40 00 00:00:00.000 SET FEATURES [Enable SATA feature] ef 00 03 00 46 00 00 00 00 00 00 40 00 00:00:00.000 SET FEATURES [Set transfer mode] Error 4 [3] occurred at disk power-on lifetime: 3 hours (0 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 08 00 00 11 61 02 50 40 00 Error: ICRC, ABRT 8 sectors at LBA = 0x11610250 = 291570256 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 08 00 00 11 61 02 50 40 00 00:00:00.000 WRITE DMA EXT 35 00 00 00 08 00 00 11 61 02 48 40 00 00:00:00.000 WRITE DMA EXT 35 00 00 00 08 00 00 11 61 02 40 40 00 00:00:00.000 WRITE DMA EXT 35 00 00 00 10 00 00 11 61 02 30 40 00 00:00:00.000 WRITE DMA EXT 35 00 00 00 08 00 00 11 61 02 28 40 00 00:00:00.000 WRITE DMA EXT Error 3 [2] occurred at disk power-on lifetime: 3 hours (0 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 80 00 00 01 10 4c b8 40 00 Error: ICRC, ABRT 128 sectors at LBA = 0x01104cb8 = 17845432 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 80 00 00 01 10 4c b8 40 00 00:00:00.000 WRITE DMA EXT 35 00 00 00 80 00 00 01 10 4c 38 40 00 00:00:00.000 WRITE DMA EXT 35 00 00 00 80 00 00 01 10 4b b8 40 00 00:00:00.000 WRITE DMA EXT 35 00 00 00 80 00 00 01 10 4b 38 40 00 00:00:00.000 WRITE DMA EXT 35 00 00 00 80 00 00 01 10 4a b8 40 00 00:00:00.000 WRITE DMA EXT Error 2 [1] occurred at disk power-on lifetime: 4 hours (0 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 80 00 00 04 14 2e 68 40 00 Error: ICRC, ABRT 128 sectors at LBA = 0x04142e68 = 68431464 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 80 00 00 04 14 2e 68 40 00 00:00:00.000 WRITE DMA EXT 35 00 00 00 80 00 00 04 14 2d e8 40 00 00:00:00.000 WRITE DMA EXT 35 00 00 00 80 00 00 04 14 2d 68 40 00 00:00:00.000 WRITE DMA EXT 35 00 00 00 80 00 00 04 14 2c e8 40 00 00:00:00.000 WRITE DMA EXT 35 00 00 00 80 00 00 04 14 2c 68 40 00 00:00:00.000 WRITE DMA EXT Error 1 [0] occurred at disk power-on lifetime: 4 hours (0 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 80 00 00 01 11 60 60 40 00 Error: ICRC, ABRT 128 sectors at LBA = 0x01116060 = 17916000 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 80 00 00 01 11 60 60 40 00 00:00:00.000 WRITE DMA EXT 35 00 00 00 80 00 00 01 11 5f e0 40 00 00:00:00.000 WRITE DMA EXT 35 00 00 00 80 00 00 01 11 5f 60 40 00 00:00:00.000 WRITE DMA EXT 35 00 00 00 80 00 00 01 11 5e e0 40 00 00:00:00.000 WRITE DMA EXT 35 00 00 00 80 00 00 01 11 5e 60 40 00 00:00:00.000 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1226 --- Lifetime Power-On Resets 0x01 0x010 4 6450 --- Power-on Hours 0x01 0x018 6 16590885337 --- Logical Sectors Written 0x01 0x028 6 14985602564 --- Logical Sectors Read 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 24 --- Current Temperature 0x05 0x020 1 34 --- Highest Temperature 0x05 0x028 1 16 --- Lowest Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x018 4 624511 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 6 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 9 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 9 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.1-desktop-1omv2290] (OpenMandriva Lx 7.3-2) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F3 Device Model: SAMSUNG HD103SJ Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 1AJ10001 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Mon Feb 13 11:39:50 2023 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 9060) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 151) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 5 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 069 065 025 - 9544 4 Start_Stop_Count -O--CK 081 081 000 - 19936 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 20667 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 252 252 000 - 0 12 Power_Cycle_Count -O--CK 094 094 000 - 6075 191 G-Sense_Error_Rate -O---K 100 100 000 - 3572 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 056 000 - 24 (Min/Max 10/44) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 2 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 55 223 Load_Retry_Count -O--CK 252 252 000 - 0 225 Load_Cycle_Count -O--CK 099 099 000 - 20018 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 2 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2 [1] occurred at disk power-on lifetime: 18381 hours (765 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 00 00 00 00 00 00 00 00 00 00 00:00:00.500 IDENTIFY DEVICE 00 00 00 00 01 00 00 00 00 00 01 00 00 00:00:00.500 NOP [Abort queued commands] 00 00 00 00 01 00 00 00 00 00 01 00 00 00:00:00.500 NOP [Abort queued commands] 00 00 00 00 01 00 00 00 00 00 01 00 00 00:00:00.470 NOP [Abort queued commands] 00 00 00 00 01 00 00 00 00 00 01 00 00 00:00:00.470 NOP [Abort queued commands] Error 1 [0] occurred at disk power-on lifetime: 18381 hours (765 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 00 00 00 00 00 00 00 00 00 00 00:00:00.470 IDENTIFY DEVICE 00 00 00 00 01 00 00 00 00 00 01 00 00 00:00:00.470 NOP [Abort queued commands] 00 00 00 00 01 00 00 00 00 00 01 00 00 00:00:00.470 NOP [Abort queued commands] ec 00 00 00 00 00 00 00 00 00 00 00 00 00:00:00.433 IDENTIFY DEVICE 00 00 00 00 01 00 00 00 00 00 01 00 00 00:00:00.420 NOP [Abort queued commands] SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 24 Celsius Power Cycle Min/Max Temperature: 21/24 Celsius Lifetime Min/Max Temperature: 12/62 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (122) Index Estimated Time Temperature Celsius 123 2023-02-13 01:00 23 **** ... ..( 6 skipped). .. **** 2 2023-02-13 01:35 23 **** 3 2023-02-13 01:40 24 ***** 4 2023-02-13 01:45 24 ***** 5 2023-02-13 01:50 25 ****** ... ..( 2 skipped). .. ****** 8 2023-02-13 02:05 25 ****** 9 2023-02-13 02:10 26 ******* 10 2023-02-13 02:15 26 ******* 11 2023-02-13 02:20 26 ******* 12 2023-02-13 02:25 25 ****** ... ..( 6 skipped). .. ****** 19 2023-02-13 03:00 25 ****** 20 2023-02-13 03:05 20 * 21 2023-02-13 03:10 22 *** 22 2023-02-13 03:15 22 *** 23 2023-02-13 03:20 23 **** ... ..( 15 skipped). .. **** 39 2023-02-13 04:40 23 **** 40 2023-02-13 04:45 21 ** 41 2023-02-13 04:50 23 **** 42 2023-02-13 04:55 24 ***** 43 2023-02-13 05:00 25 ****** 44 2023-02-13 05:05 25 ****** 45 2023-02-13 05:10 24 ***** 46 2023-02-13 05:15 25 ****** 47 2023-02-13 05:20 25 ****** 48 2023-02-13 05:25 25 ****** 49 2023-02-13 05:30 20 * 50 2023-02-13 05:35 20 * 51 2023-02-13 05:40 22 *** 52 2023-02-13 05:45 23 **** 53 2023-02-13 05:50 23 **** 54 2023-02-13 05:55 24 ***** ... ..( 4 skipped). .. ***** 59 2023-02-13 06:20 24 ***** 60 2023-02-13 06:25 23 **** ... ..( 6 skipped). .. **** 67 2023-02-13 07:00 23 **** 68 2023-02-13 07:05 20 * 69 2023-02-13 07:10 21 ** 70 2023-02-13 07:15 22 *** 71 2023-02-13 07:20 22 *** 72 2023-02-13 07:25 20 * 73 2023-02-13 07:30 21 ** 74 2023-02-13 07:35 19 - 75 2023-02-13 07:40 23 **** 76 2023-02-13 07:45 27 ******** 77 2023-02-13 07:50 21 ** 78 2023-02-13 07:55 20 * 79 2023-02-13 08:00 23 **** 80 2023-02-13 08:05 25 ****** 81 2023-02-13 08:10 25 ****** 82 2023-02-13 08:15 25 ****** 83 2023-02-13 08:20 19 - 84 2023-02-13 08:25 23 **** 85 2023-02-13 08:30 23 **** 86 2023-02-13 08:35 19 - 87 2023-02-13 08:40 21 ** 88 2023-02-13 08:45 21 ** 89 2023-02-13 08:50 22 *** ... ..( 5 skipped). .. *** 95 2023-02-13 09:20 22 *** 96 2023-02-13 09:25 18 - 97 2023-02-13 09:30 20 * 98 2023-02-13 09:35 21 ** 99 2023-02-13 09:40 22 *** 100 2023-02-13 09:45 22 *** 101 2023-02-13 09:50 20 * 102 2023-02-13 09:55 21 ** 103 2023-02-13 10:00 22 *** 104 2023-02-13 10:05 22 *** 105 2023-02-13 10:10 22 *** 106 2023-02-13 10:15 19 - 107 2023-02-13 10:20 21 ** 108 2023-02-13 10:25 22 *** 109 2023-02-13 10:30 22 *** 110 2023-02-13 10:35 21 ** 111 2023-02-13 10:40 22 *** 112 2023-02-13 10:45 24 ***** ... ..( 9 skipped). .. ***** 122 2023-02-13 11:35 24 ***** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 9 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 8 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific /dev/sdc smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.1-desktop-1omv2290] (OpenMandriva Lx 7.3-2) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST2000DM001-1CH164 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC24 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Mon Feb 13 11:39:51 2023 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 592) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 233) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 106 078 006 - 221555608 3 Spin_Up_Time PO---- 098 096 000 - 0 4 Start_Stop_Count -O--CK 085 085 020 - 15553 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 074 060 030 - 26440332 9 Power_On_Hours -O--CK 079 079 000 - 19142 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 4914 183 Runtime_Bad_Block -O--CK 075 075 000 - 25 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 2010 188 Command_Timeout -O--CK 100 001 000 - 710 710 732 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 076 051 045 - 24 (0 2 24 19 0) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 869 193 Load_Cycle_Count -O--CK 064 064 000 - 72837 194 Temperature_Celsius -O---K 024 049 000 - 24 (128 0 0 0 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 8 198 Offline_Uncorrectable ----C- 100 100 000 - 8 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 24 240 Head_Flying_Hours ------ 100 253 000 - 5015h+56m+19.270s 241 Total_LBAs_Written ------ 100 253 000 - 15119740702 242 Total_LBAs_Read ------ 100 253 000 - 17621241647 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xbd GPL VS 512 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc4 GPL,SL VS 5 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 1366 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1366 [5] occurred at disk power-on lifetime: 19000 hours (791 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 2d c2 fe 22 00 00 Error: UNC at LBA = 0x2dc2fe22 = 767753762 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 2d c2 fe 22 e0 00 01:40:07.192 READ DMA EXT 25 00 00 00 02 00 00 2d c2 fe 2e e0 00 01:40:04.273 READ DMA EXT 25 00 00 01 00 00 00 2d c2 fe 22 e0 00 01:40:01.350 READ DMA EXT 25 00 00 00 02 00 00 2d c2 fe 2c e0 00 01:39:58.441 READ DMA EXT 25 00 00 01 00 00 00 2d c2 fe 22 e0 00 01:39:55.507 READ DMA EXT Error 1365 [4] occurred at disk power-on lifetime: 19000 hours (791 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 2d c2 fe 22 00 00 Error: UNC at LBA = 0x2dc2fe22 = 767753762 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 2d c2 fe 22 e0 00 01:40:01.350 READ DMA EXT 25 00 00 00 02 00 00 2d c2 fe 2c e0 00 01:39:58.441 READ DMA EXT 25 00 00 01 00 00 00 2d c2 fe 22 e0 00 01:39:55.507 READ DMA EXT 25 00 00 00 02 00 00 2d c2 fe 2a e0 00 01:39:52.599 READ DMA EXT 25 00 00 01 00 00 00 2d c2 fe 22 e0 00 01:39:49.714 READ DMA EXT Error 1364 [3] occurred at disk power-on lifetime: 19000 hours (791 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 2d c2 fe 22 00 00 Error: UNC at LBA = 0x2dc2fe22 = 767753762 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 2d c2 fe 22 e0 00 01:39:55.507 READ DMA EXT 25 00 00 00 02 00 00 2d c2 fe 2a e0 00 01:39:52.599 READ DMA EXT 25 00 00 01 00 00 00 2d c2 fe 22 e0 00 01:39:49.714 READ DMA EXT 25 00 00 01 00 00 00 18 dc cd 22 e0 00 01:39:49.659 READ DMA EXT 25 00 00 01 00 00 00 2d c2 fd 22 e0 00 01:39:46.787 READ DMA EXT Error 1363 [2] occurred at disk power-on lifetime: 19000 hours (791 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 2d c2 fe 22 00 00 Error: UNC at LBA = 0x2dc2fe22 = 767753762 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 2d c2 fe 22 e0 00 01:39:49.714 READ DMA EXT 25 00 00 01 00 00 00 18 dc cd 22 e0 00 01:39:49.659 READ DMA EXT 25 00 00 01 00 00 00 2d c2 fd 22 e0 00 01:39:46.787 READ DMA EXT 25 00 00 01 00 00 00 2d c2 fc 22 e0 00 01:39:46.785 READ DMA EXT 25 00 00 01 00 00 00 2d c2 fb 22 e0 00 01:39:46.783 READ DMA EXT Error 1362 [1] occurred at disk power-on lifetime: 18999 hours (791 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 2d c2 fe 22 00 00 Error: UNC at LBA = 0x2dc2fe22 = 767753762 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 2d c2 fe 22 e0 00 01:33:32.576 READ DMA EXT 35 00 00 00 08 00 00 2d be d0 ca e0 00 01:33:32.576 WRITE DMA EXT 25 00 00 00 02 00 00 2d c2 fe 2a e0 00 01:33:29.643 READ DMA EXT 35 00 00 00 20 00 00 5a 90 5b 02 e0 00 01:33:29.643 WRITE DMA EXT 25 00 00 01 00 00 00 2d c2 fe 22 e0 00 01:33:26.758 READ DMA EXT Error 1361 [0] occurred at disk power-on lifetime: 18999 hours (791 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 2d c2 fe 22 00 00 Error: UNC at LBA = 0x2dc2fe22 = 767753762 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 2d c2 fe 22 e0 00 01:33:26.758 READ DMA EXT 25 00 00 00 20 00 00 2d be d0 c2 e0 00 01:33:26.692 READ DMA EXT 25 00 00 01 00 00 00 2d c2 fe 22 e0 00 01:33:23.809 READ DMA EXT ea 00 00 00 00 c2 fe 22 00 00 00 a0 00 01:33:23.708 FLUSH CACHE EXT 25 00 00 01 00 00 00 2d c2 fe 22 e0 00 01:33:20.832 READ DMA EXT Error 1360 [19] occurred at disk power-on lifetime: 18999 hours (791 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 2d c2 fe 22 00 00 Error: UNC at LBA = 0x2dc2fe22 = 767753762 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 2d c2 fe 22 e0 00 01:33:23.809 READ DMA EXT ea 00 00 00 00 c2 fe 22 00 00 00 a0 00 01:33:23.708 FLUSH CACHE EXT 25 00 00 01 00 00 00 2d c2 fe 22 e0 00 01:33:20.832 READ DMA EXT 25 00 00 01 00 00 00 18 dc cd 22 e0 00 01:33:20.766 READ DMA EXT 25 00 00 01 00 00 00 2d c2 fd 22 e0 00 01:33:17.888 READ DMA EXT Error 1359 [18] occurred at disk power-on lifetime: 18999 hours (791 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 2d c2 fe 22 00 00 Error: UNC at LBA = 0x2dc2fe22 = 767753762 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 2d c2 fe 22 e0 00 01:33:20.832 READ DMA EXT 25 00 00 01 00 00 00 18 dc cd 22 e0 00 01:33:20.766 READ DMA EXT 25 00 00 01 00 00 00 2d c2 fd 22 e0 00 01:33:17.888 READ DMA EXT 25 00 00 01 00 00 00 2d c2 fc 22 e0 00 01:33:17.874 READ DMA EXT 25 00 00 01 00 00 00 2d c2 fb 22 e0 00 01:33:17.870 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 24 Celsius Power Cycle Min/Max Temperature: 19/24 Celsius Lifetime Min/Max Temperature: 13/46 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 9 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS