/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.10.74-generic-2rosa2021.1-x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: P3-256 Serial Number: -- LU WWN Device Id: 5 000000 ... Firmware Version: H190225a User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: Not in smartctl database 7.3/5319 ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jun 8 13:12:44 2022 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 33) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 2) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 9 Power_On_Hours -O--C- 100 100 000 - 11113 12 Power_Cycle_Count -O--C- 100 100 000 - 893 167 Unknown_Attribute -O---K 100 100 000 - 0 168 Unknown_Attribute -O--C- 100 100 000 - 83 169 Unknown_Attribute PO--C- 090 090 010 - 4718610 171 Unknown_Attribute -O--CK 000 000 000 - 0 172 Unknown_Attribute -O--CK 000 000 000 - 0 173 Unknown_Attribute -O--C- 200 200 000 - 1000746647815 175 Program_Fail_Count_Chip -O---K 100 100 010 - 0 180 Unused_Rsvd_Blk_Cnt_Tot PO--CK 100 100 000 - 684 187 Reported_Uncorrect -O--CK 100 000 000 - 79 192 Power-Off_Retract_Count -O--C- 100 100 000 - 332 194 Temperature_Celsius -O---K 030 030 000 - 30 (Min/Max 10/50) 206 Unknown_SSD_Attribute -O--CK 200 200 000 - 233 207 Unknown_SSD_Attribute -O--CK 200 200 000 - 294 208 Unknown_SSD_Attribute -O--CK 200 200 000 - 263 209 Unknown_SSD_Attribute -O--CK 200 200 000 - 670 210 Unknown_Attribute -O--CK 200 200 000 - 1120 211 Unknown_Attribute -O--CK 200 200 000 - 884 231 Unknown_SSD_Attribute PO---K 083 083 005 - 17 233 Media_Wearout_Indicator -O--CK 100 100 000 - 142279271808 234 Unknown_Attribute -O--CK 100 100 000 - 1286885127 241 Total_LBAs_Written -O--CK 100 100 000 - 69971790395 242 Total_LBAs_Read -O--CK 100 100 000 - 55475749079 245 Unknown_Attribute -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 83 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 83 [82] occurred at disk power-on lifetime: 9505 hours (396 days + 1 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 01 00 00 00 00 21 cf 00 40 00 Error: UNC at LBA = 0x0021cf00 = 2215680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 f0 00 00 00 21 cf 30 a0 80 00:01:14.600 READ FPDMA QUEUED ec 00 00 00 00 00 00 00 00 00 00 a0 80 00:01:14.400 IDENTIFY DEVICE ea 00 00 00 00 00 00 00 00 00 00 a0 80 00:01:14.200 FLUSH CACHE EXT ea 00 00 00 00 00 00 00 00 00 00 a0 80 00:01:14.200 FLUSH CACHE EXT ea 00 00 00 00 00 00 00 00 00 00 a0 80 00:01:14.200 FLUSH CACHE EXT Error 82 [81] occurred at disk power-on lifetime: 9505 hours (396 days + 1 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 40 00 00 01 13 38 92 40 00 Error: UNC at LBA = 0x01133892 = 18036882 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 18 00 00 00 21 cf 30 e0 80 00:01:13.600 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 80 00:01:13.500 READ LOG EXT 60 00 40 00 b8 00 00 00 21 cf 30 e0 80 00:01:13.500 READ FPDMA QUEUED 06 00 01 00 01 00 00 00 00 00 00 e0 80 00:01:13.100 DATA SET MANAGEMENT ea 00 00 00 00 00 00 00 00 00 00 a0 80 00:01:13.100 FLUSH CACHE EXT Error 81 [80] occurred at disk power-on lifetime: 9505 hours (396 days + 1 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 40 00 00 01 2b 3a c0 40 00 Error: UNC at LBA = 0x012b3ac0 = 19610304 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 b8 00 00 00 21 cf 30 e0 80 00:01:13.500 READ FPDMA QUEUED 06 00 01 00 01 00 00 00 00 00 00 e0 80 00:01:13.100 DATA SET MANAGEMENT ea 00 00 00 00 00 00 00 00 00 00 a0 80 00:01:13.100 FLUSH CACHE EXT ea 00 00 00 00 00 00 00 00 00 00 a0 80 00:01:12.600 FLUSH CACHE EXT ea 00 00 00 00 00 00 00 00 00 00 a0 80 00:01:09.900 FLUSH CACHE EXT Error 80 [79] occurred at disk power-on lifetime: 9475 hours (394 days + 19 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 f8 00 00 00 3e 0c 90 40 00 Error: UNC at LBA = 0x003e0c90 = 4066448 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 21 cf 30 e0 80 10:15:03.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 80 10:15:03.300 READ LOG EXT 60 00 00 00 e0 00 00 00 21 cf 30 e0 80 10:15:03.300 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 80 10:15:03.200 READ LOG EXT 60 00 00 00 c0 00 00 00 21 cf 30 e0 80 10:15:03.200 READ FPDMA QUEUED Error 79 [78] occurred at disk power-on lifetime: 9475 hours (394 days + 19 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 00 3e 0b 88 40 00 Error: UNC at LBA = 0x003e0b88 = 4066184 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 e0 00 00 00 21 cf 30 e0 80 10:15:03.300 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 80 10:15:03.200 READ LOG EXT 60 00 00 00 c0 00 00 00 21 cf 30 e0 80 10:15:03.200 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 80 10:15:03.100 READ LOG EXT 60 00 00 00 a8 00 00 00 21 cf 30 e0 80 10:15:03.100 READ FPDMA QUEUED Error 78 [77] occurred at disk power-on lifetime: 9475 hours (394 days + 19 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 20 00 00 09 15 c5 80 40 00 Error: UNC at LBA = 0x0915c580 = 152421760 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 c0 00 00 00 21 cf 30 e0 80 10:15:03.200 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 80 10:15:03.100 READ LOG EXT 60 00 00 00 a8 00 00 00 21 cf 30 e0 80 10:15:03.100 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 80 10:15:03.000 READ LOG EXT 60 00 00 00 88 00 00 00 21 cf 30 e0 80 10:15:03.000 READ FPDMA QUEUED Error 77 [76] occurred at disk power-on lifetime: 9475 hours (394 days + 19 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 80 00 00 00 3e 12 90 40 00 Error: UNC at LBA = 0x003e1290 = 4067984 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 a8 00 00 00 21 cf 30 e0 80 10:15:03.100 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 80 10:15:03.000 READ LOG EXT 60 00 00 00 88 00 00 00 21 cf 30 e0 80 10:15:03.000 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 80 10:15:02.900 READ LOG EXT 60 00 00 00 78 00 00 00 21 cf 30 e0 80 10:15:02.900 READ FPDMA QUEUED Error 76 [75] occurred at disk power-on lifetime: 9475 hours (394 days + 19 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 01 00 00 00 00 21 cf 00 40 00 Error: UNC at LBA = 0x0021cf00 = 2215680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 88 00 00 00 21 cf 30 e0 80 10:15:03.000 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 80 10:15:02.900 READ LOG EXT 60 00 00 00 78 00 00 00 21 cf 30 e0 80 10:15:02.900 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 80 10:15:02.800 READ LOG EXT 60 00 00 00 68 00 00 00 21 cf 30 e0 80 10:15:02.700 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: ?/30 Celsius Lifetime Min/Max Temperature: ?/ ? Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -127/127 Celsius Min/Max Temperature Limit: -127/127 Celsius Temperature History Size (Index): 478 (443) Index Estimated Time Temperature Celsius 444 2022-06-08 05:15 30 *********** ... ..( 85 skipped). .. *********** 52 2022-06-08 06:41 30 *********** 53 2022-06-08 06:42 ? - 54 2022-06-08 06:43 30 *********** ... ..(388 skipped). .. *********** 443 2022-06-08 13:12 30 *********** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 893 --- Lifetime Power-On Resets 0x01 0x010 4 11113 --- Power-on Hours 0x01 0x018 6 69971790395 --- Logical Sectors Written 0x01 0x020 6 590577799 --- Number of Write Commands 0x01 0x028 6 55475749079 --- Logical Sectors Read 0x01 0x030 6 648454095 --- Number of Read Commands 0x01 0x038 6 142048285495796 --- Date and Time TimeStamp 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 39 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 83 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 26 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.10.74-generic-2rosa2021.1-x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Momentus 5400.6 Device Model: ST9500325AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0011LVM1 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Wed Jun 8 13:12:44 2022 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 138) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 113 075 034 - 50434678 3 Spin_Up_Time PO---- 099 098 000 - 0 4 Start_Stop_Count -O--CK 092 092 020 - 8718 5 Reallocated_Sector_Ct PO--CK 004 004 036 NOW 1981 7 Seek_Error_Rate POSR-- 090 060 030 - 5300479953 9 Power_On_Hours -O--CK 053 053 000 - 41510 (158 125 0) 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 4998 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 34225 188 Command_Timeout -O--CK 100 082 000 - 953497551235 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 071 036 045 Past 29 (Min/Max 25/43 #5609) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 313 192 Power-Off_Retract_Count -O--CK 100 100 000 - 0 193 Load_Cycle_Count -O--CK 001 001 000 - 384867 194 Temperature_Celsius -O---K 029 064 000 - 29 (0 3 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 050 034 000 - 50434678 196 Reallocated_Event_Count POSR-- 063 063 030 - 32432 (45926 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 36 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 35857 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 35857 [16] occurred at disk power-on lifetime: 40743 hours (1697 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 10 00 e7 39 6a 00 00 Error: UNC at LBA = 0x1000e7396a = 68734630250 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 10 00 e7 39 68 40 00 05:30:49.621 READ FPDMA QUEUED 61 00 00 00 08 00 8b 00 d8 1d 30 40 00 05:30:49.621 WRITE FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 05:30:49.579 READ LOG EXT 60 00 00 00 08 00 10 00 e7 39 68 40 00 05:30:47.400 READ FPDMA QUEUED 61 00 00 00 08 00 0e 00 10 13 50 40 00 05:30:47.400 WRITE FPDMA QUEUED Error 35856 [15] occurred at disk power-on lifetime: 40743 hours (1697 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 10 00 e7 39 6a 00 00 Error: UNC at LBA = 0x1000e7396a = 68734630250 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 10 00 e7 39 68 40 00 05:30:47.400 READ FPDMA QUEUED 61 00 00 00 08 00 0e 00 10 13 50 40 00 05:30:47.400 WRITE FPDMA QUEUED 61 00 00 00 08 00 0e 00 10 13 48 40 00 05:30:47.399 WRITE FPDMA QUEUED 61 00 00 00 08 00 0e 00 10 13 40 40 00 05:30:47.399 WRITE FPDMA QUEUED 61 00 00 00 08 00 8b 00 de 1d 98 40 00 05:30:47.399 WRITE FPDMA QUEUED Error 35855 [14] occurred at disk power-on lifetime: 40743 hours (1697 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 10 00 e7 39 6a 00 00 Error: WP at LBA = 0x1000e7396a = 68734630250 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 5d 00 93 00 80 40 00 05:30:45.085 WRITE FPDMA QUEUED 60 00 00 00 08 00 10 00 e7 39 68 40 00 05:30:45.083 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 05:30:45.034 FLUSH CACHE EXT 61 00 00 00 08 00 5d 00 93 00 90 40 00 05:30:45.033 WRITE FPDMA QUEUED 61 00 00 00 a0 00 5f 00 8b 00 18 40 00 05:30:45.033 WRITE FPDMA QUEUED Error 35854 [13] occurred at disk power-on lifetime: 40743 hours (1697 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 10 00 e7 39 6a 00 00 Error: UNC at LBA = 0x1000e7396a = 68734630250 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 10 00 e7 39 68 40 00 05:30:42.765 READ FPDMA QUEUED 61 00 00 00 08 00 0e 00 10 13 30 40 00 05:30:42.764 WRITE FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 05:30:42.734 READ LOG EXT 60 00 00 00 08 00 10 00 e7 39 68 40 00 05:30:40.533 READ FPDMA QUEUED 61 00 00 00 08 00 0e 00 10 13 28 40 00 05:30:40.532 WRITE FPDMA QUEUED Error 35853 [12] occurred at disk power-on lifetime: 40743 hours (1697 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 10 00 e7 39 6a 00 00 Error: UNC at LBA = 0x1000e7396a = 68734630250 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 10 00 e7 39 68 40 00 05:30:40.533 READ FPDMA QUEUED 61 00 00 00 08 00 0e 00 10 13 28 40 00 05:30:40.532 WRITE FPDMA QUEUED 61 00 00 00 08 00 0e 00 10 13 20 40 00 05:30:40.532 WRITE FPDMA QUEUED 61 00 00 00 08 00 0e 00 10 13 18 40 00 05:30:40.531 WRITE FPDMA QUEUED 61 00 00 00 08 00 0e 00 10 13 10 40 00 05:30:40.531 WRITE FPDMA QUEUED Error 35852 [11] occurred at disk power-on lifetime: 40743 hours (1697 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 10 00 e7 39 6a 00 00 Error: WP at LBA = 0x1000e7396a = 68734630250 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 5d 00 93 00 88 40 00 05:30:38.231 WRITE FPDMA QUEUED 60 00 00 00 08 00 10 00 e7 39 68 40 00 05:30:38.229 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 05:30:38.166 FLUSH CACHE EXT 61 00 00 00 08 00 5d 00 94 00 10 40 00 05:30:38.166 WRITE FPDMA QUEUED 61 00 00 00 a8 00 5f 00 8a 00 70 40 00 05:30:38.165 WRITE FPDMA QUEUED Error 35851 [10] occurred at disk power-on lifetime: 40743 hours (1697 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 10 00 e7 39 6a 00 00 Error: UNC at LBA = 0x1000e7396a = 68734630250 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 10 00 e7 39 68 40 00 05:30:35.897 READ FPDMA QUEUED 61 00 00 00 08 00 0e 00 10 13 00 40 00 05:30:35.896 WRITE FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 05:30:35.866 READ LOG EXT 60 00 00 00 08 00 10 00 e7 39 68 40 00 05:30:33.665 READ FPDMA QUEUED 61 00 00 00 18 00 0e 00 0f 13 e0 40 00 05:30:33.665 WRITE FPDMA QUEUED Error 35850 [9] occurred at disk power-on lifetime: 40743 hours (1697 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 10 00 e7 39 6a 00 00 Error: UNC at LBA = 0x1000e7396a = 68734630250 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 10 00 e7 39 68 40 00 05:30:33.665 READ FPDMA QUEUED 61 00 00 00 18 00 0e 00 0f 13 e0 40 00 05:30:33.665 WRITE FPDMA QUEUED 61 00 00 00 08 00 0e 00 0f 13 d8 40 00 05:30:33.664 WRITE FPDMA QUEUED 61 00 00 00 08 00 0e 00 0f 13 d0 40 00 05:30:33.664 WRITE FPDMA QUEUED 61 00 00 00 08 00 0e 00 0f 13 c8 40 00 05:30:33.663 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Conveyance offline Completed without error 00% 1 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 25/43 Celsius Lifetime Min/Max Temperature: 3/64 Celsius Under/Over Temperature Limit Count: 0/14 Vendor specific: 00 00 00 00 00 00 00 00 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 11 minutes Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (66) Index Estimated Time Temperature Celsius 67 2022-06-07 13:47 26 ******* 68 2022-06-07 13:58 27 ******** ... ..( 3 skipped). .. ******** 72 2022-06-07 14:42 27 ******** 73 2022-06-07 14:53 26 ******* ... ..( 4 skipped). .. ******* 78 2022-06-07 15:48 26 ******* 79 2022-06-07 15:59 27 ******** ... ..( 4 skipped). .. ******** 84 2022-06-07 16:54 27 ******** 85 2022-06-07 17:05 28 ********* ... ..( 2 skipped). .. ********* 88 2022-06-07 17:38 28 ********* 89 2022-06-07 17:49 27 ******** ... ..( 14 skipped). .. ******** 104 2022-06-07 20:34 27 ******** 105 2022-06-07 20:45 28 ********* 106 2022-06-07 20:56 28 ********* 107 2022-06-07 21:07 28 ********* 108 2022-06-07 21:18 27 ******** 109 2022-06-07 21:29 26 ******* 110 2022-06-07 21:40 26 ******* 111 2022-06-07 21:51 25 ****** ... ..( 5 skipped). .. ****** 117 2022-06-07 22:57 25 ****** 118 2022-06-07 23:08 24 ***** 119 2022-06-07 23:19 25 ****** 120 2022-06-07 23:30 25 ****** 121 2022-06-07 23:41 41 ********************** 122 2022-06-07 23:52 33 ************** 123 2022-06-08 00:03 29 ********** 124 2022-06-08 00:14 30 *********** 125 2022-06-08 00:25 28 ********* 126 2022-06-08 00:36 32 ************* 127 2022-06-08 00:47 43 ************************ 0 2022-06-08 00:58 44 ************************* 1 2022-06-08 01:09 43 ************************ 2 2022-06-08 01:20 43 ************************ 3 2022-06-08 01:31 38 ******************* 4 2022-06-08 01:42 39 ******************** 5 2022-06-08 01:53 37 ****************** ... ..( 2 skipped). .. ****************** 8 2022-06-08 02:26 37 ****************** 9 2022-06-08 02:37 36 ***************** 10 2022-06-08 02:48 38 ******************* 11 2022-06-08 02:59 40 ********************* 12 2022-06-08 03:10 39 ******************** 13 2022-06-08 03:21 41 ********************** 14 2022-06-08 03:32 41 ********************** 15 2022-06-08 03:43 41 ********************** 16 2022-06-08 03:54 ? - 17 2022-06-08 04:05 22 *** 18 2022-06-08 04:16 26 ******* 19 2022-06-08 04:27 25 ****** 20 2022-06-08 04:38 27 ******** 21 2022-06-08 04:49 27 ******** 22 2022-06-08 05:00 28 ********* 23 2022-06-08 05:11 29 ********** 24 2022-06-08 05:22 28 ********* 25 2022-06-08 05:33 31 ************ 26 2022-06-08 05:44 31 ************ 27 2022-06-08 05:55 29 ********** 28 2022-06-08 06:06 33 ************** 29 2022-06-08 06:17 37 ****************** 30 2022-06-08 06:28 33 ************** 31 2022-06-08 06:39 30 *********** 32 2022-06-08 06:50 29 ********** 33 2022-06-08 07:01 30 *********** 34 2022-06-08 07:12 27 ******** 35 2022-06-08 07:23 28 ********* 36 2022-06-08 07:34 37 ****************** 37 2022-06-08 07:45 33 ************** 38 2022-06-08 07:56 39 ******************** 39 2022-06-08 08:07 39 ******************** 40 2022-06-08 08:18 29 ********** 41 2022-06-08 08:29 35 **************** 42 2022-06-08 08:40 35 **************** 43 2022-06-08 08:51 37 ****************** 44 2022-06-08 09:02 35 **************** 45 2022-06-08 09:13 36 ***************** 46 2022-06-08 09:24 ? - 47 2022-06-08 09:35 26 ******* 48 2022-06-08 09:46 27 ******** 49 2022-06-08 09:57 42 *********************** 50 2022-06-08 10:08 42 *********************** 51 2022-06-08 10:19 43 ************************ 52 2022-06-08 10:30 ? - 53 2022-06-08 10:41 25 ****** 54 2022-06-08 10:52 28 ********* 55 2022-06-08 11:03 28 ********* 56 2022-06-08 11:14 43 ************************ 57 2022-06-08 11:25 40 ********************* 58 2022-06-08 11:36 27 ******** ... ..( 3 skipped). .. ******** 62 2022-06-08 12:20 27 ******** 63 2022-06-08 12:31 29 ********** 64 2022-06-08 12:42 29 ********** 65 2022-06-08 12:53 28 ********* 66 2022-06-08 13:04 29 ********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 33 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS