/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.0.12-76060006-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda SpinPoint F3 Device Model: ST1000DM005 HD103SJ Serial Number: -- LU WWN Device Id: 5 0004cf ... Firmware Version: 1AJ10001 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Mon Jan 2 15:36:21 2023 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 9300) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 155) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 151 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 084 068 025 - 5138 4 Start_Stop_Count -O--CK 098 098 000 - 2337 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 11550 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 252 252 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2195 191 G-Sense_Error_Rate -O---K 100 100 000 - 50 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 054 000 - 25 (Min/Max 11/46) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 547 223 Load_Retry_Count -O--CK 252 252 000 - 0 225 Load_Cycle_Count -O--CK 100 100 000 - 2468 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 2 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2 [1] occurred at disk power-on lifetime: 11494 hours (478 days + 22 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 00 3f fe 3f af 00 Error: IDNF at LBA = 0x0f3ffe3f = 255852095 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 31 00 f1 00 01 00 00 00 00 00 00 a0 00 00:00:00.214 WRITE SECTOR(S) (w/o retry) [OBS-5] e0 00 00 00 6f 00 00 00 fa ef fe af 00 00:00:00.212 STANDBY IMMEDIATE 61 00 00 00 10 00 00 00 08 7a 18 40 00 00:00:00.211 WRITE FPDMA QUEUED 61 00 00 00 20 00 00 00 09 5e 90 40 00 00:00:00.211 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 07 2e ce f0 40 00 00:00:00.211 WRITE FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 11494 hours (478 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 00 3f fe 3f af 00 Error: IDNF at LBA = 0x0f3ffe3f = 255852095 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 31 00 f1 00 01 00 00 00 00 00 00 a0 00 00:00:02.203 WRITE SECTOR(S) (w/o retry) [OBS-5] 61 00 00 00 d0 00 00 00 5c ee 38 40 00 00:00:02.203 WRITE FPDMA QUEUED 61 00 00 01 00 00 00 00 5c ed 38 40 00 00:00:02.203 WRITE FPDMA QUEUED 61 00 00 01 00 00 00 00 5c ec 38 40 00 00:00:02.203 WRITE FPDMA QUEUED 61 00 00 01 00 00 00 00 5c eb 38 40 00 00:00:02.203 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 25 Celsius Power Cycle Min/Max Temperature: 25/25 Celsius Lifetime Min/Max Temperature: 15/61 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (39) Index Estimated Time Temperature Celsius 40 2023-01-02 05:00 25 ****** ... ..( 22 skipped). .. ****** 63 2023-01-02 06:55 25 ****** 64 2023-01-02 07:00 23 **** 65 2023-01-02 07:05 24 ***** 66 2023-01-02 07:10 24 ***** 67 2023-01-02 07:15 25 ****** 68 2023-01-02 07:20 25 ****** 69 2023-01-02 07:25 25 ****** 70 2023-01-02 07:30 20 * 71 2023-01-02 07:35 22 *** 72 2023-01-02 07:40 23 **** 73 2023-01-02 07:45 24 ***** 74 2023-01-02 07:50 25 ****** 75 2023-01-02 07:55 25 ****** 76 2023-01-02 08:00 26 ******* 77 2023-01-02 08:05 25 ****** 78 2023-01-02 08:10 25 ****** 79 2023-01-02 08:15 26 ******* ... ..( 6 skipped). .. ******* 86 2023-01-02 08:50 26 ******* 87 2023-01-02 08:55 25 ****** ... ..( 3 skipped). .. ****** 91 2023-01-02 09:15 25 ****** 92 2023-01-02 09:20 26 ******* ... ..( 29 skipped). .. ******* 122 2023-01-02 11:50 26 ******* 123 2023-01-02 11:55 25 ****** 124 2023-01-02 12:00 26 ******* 125 2023-01-02 12:05 25 ****** ... ..( 22 skipped). .. ****** 20 2023-01-02 14:00 25 ****** 21 2023-01-02 14:05 26 ******* ... ..( 2 skipped). .. ******* 24 2023-01-02 14:20 26 ******* 25 2023-01-02 14:25 25 ****** 26 2023-01-02 14:30 19 - 27 2023-01-02 14:35 21 ** 28 2023-01-02 14:40 22 *** 29 2023-01-02 14:45 23 **** 30 2023-01-02 14:50 23 **** 31 2023-01-02 14:55 24 ***** 32 2023-01-02 15:00 25 ****** ... ..( 6 skipped). .. ****** 39 2023-01-02 15:35 25 ****** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 37 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.0.12-76060006-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 840 EVO 120GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: EXT0BB6Q User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available Device is: In smartctl database ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jan 2 15:36:22 2023 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Unexpected SCT status 0x0001 (action_code=4, function_code=2) Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4200) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 70) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 097 097 000 - 14290 12 Power_Cycle_Count -O--CK 098 098 000 - 1723 177 Wear_Leveling_Count PO--C- 097 097 000 - 32 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 079 058 000 - 21 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 145 241 Total_LBAs_Written -O--CK 099 099 000 - 8785426014 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 16 Device vendor specific log 0xce GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 21 Celsius Power Cycle Min/Max Temperature: ?/ ? Celsius Lifetime Min/Max Temperature: ?/ ? Celsius Under/Over Temperature Limit Count: 0/85734 SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: ?/ ? Celsius Min/Max Temperature Limit: ?/ ? Celsius Temperature History Size (Index): 128 (4) Index Estimated Time Temperature Celsius 5 2023-01-01 18:20 ? - ... ..(122 skipped). .. - 0 2023-01-02 14:50 ? - 1 2023-01-02 15:00 21 ** 2 2023-01-02 15:10 21 ** 3 2023-01-02 15:20 24 ***** 4 2023-01-02 15:30 22 *** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 2168 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdc smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.0.12-76060006-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba 2.5" HDD MK..55GSX Device Model: TOSHIBA MK1655GSX Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: FG011J User Capacity: 160,041,885,696 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Mon Jan 2 15:36:22 2023 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 33) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 73) minutes. SCT capabilities: (0x0039) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--K 100 100 001 - 733 4 Start_Stop_Count -O--CK 100 100 000 - 6900 5 Reallocated_Sector_Ct PO--CK 100 100 050 - 203 7 Seek_Error_Rate PO-R-- 100 100 050 - 0 8 Seek_Time_Performance P-S--- 100 100 050 - 0 9 Power_On_Hours -O--CK 075 075 000 - 10060 10 Spin_Retry_Count PO--CK 237 100 030 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 2670 191 G-Sense_Error_Rate -O--CK 100 100 000 - 1063 192 Power-Off_Retract_Count -O--CK 100 100 000 - 149 193 Load_Cycle_Count -O--CK 095 095 000 - 54900 194 Temperature_Celsius -O---K 100 100 000 - 22 (Min/Max 10/55) 196 Reallocated_Event_Count -O--CK 100 100 000 - 38 197 Current_Pending_Sector -O--CK 100 100 000 - 74 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 220 Disk_Shift -O---- 100 100 000 - 53 222 Loaded_Hours -O--CK 093 093 000 - 2826 223 Load_Retry_Count -O--CK 100 100 000 - 0 224 Load_Friction -O---K 100 100 000 - 0 226 Load-in_Time -OS--K 100 100 000 - 354 240 Head_Flying_Hours P----- 100 100 001 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 7977 (device log contains only the most recent 256 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 7977 [40] occurred at disk power-on lifetime: 10055 hours (418 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 3a 00 00 01 9c cc a0 61 00 Error: UNC at LBA = 0x019ccca0 = 27053216 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 38 00 00 01 9c cc a0 40 08 01:02:30.008 READ FPDMA QUEUED ef 00 10 00 02 a1 9e af 00 00 00 a0 00 01:02:30.008 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:02:30.008 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 45 00 00 00 00 00 00 00 a0 00 01:02:30.007 IDENTIFY DEVICE ef 10 03 02 45 00 00 00 00 00 00 a0 00 01:02:30.007 SET FEATURES [Set transfer mode] Error 7976 [39] occurred at disk power-on lifetime: 10055 hours (418 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 8a 00 00 01 9c cc a0 61 00 Error: UNC at LBA = 0x019ccca0 = 27053216 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 88 00 00 01 9c cc a0 40 08 01:02:21.587 READ FPDMA QUEUED ef 00 10 00 02 a1 9e af 00 00 00 a0 00 01:02:21.586 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:02:21.586 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 45 00 00 00 00 00 00 00 a0 00 01:02:21.586 IDENTIFY DEVICE ef 10 03 02 45 00 00 00 00 00 00 a0 00 01:02:21.586 SET FEATURES [Set transfer mode] Error 7975 [38] occurred at disk power-on lifetime: 10055 hours (418 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 82 00 00 01 9c cc a0 61 00 Error: UNC at LBA = 0x019ccca0 = 27053216 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 80 00 00 01 9c cc a0 40 08 01:02:13.041 READ FPDMA QUEUED ef 00 10 00 02 a1 9e af 00 00 00 a0 00 01:02:13.041 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:02:13.041 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 45 00 00 00 00 00 00 00 a0 00 01:02:13.040 IDENTIFY DEVICE ef 10 03 02 45 00 00 00 00 00 00 a0 00 01:02:13.040 SET FEATURES [Set transfer mode] Error 7974 [37] occurred at disk power-on lifetime: 10055 hours (418 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 7a 00 00 01 9c cc 99 61 00 Error: UNC at LBA = 0x019ccc99 = 27053209 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 78 00 00 01 9c cc 98 40 08 01:02:04.573 READ FPDMA QUEUED ef 00 10 00 02 a1 9e af 00 00 00 a0 00 01:02:04.573 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:02:04.573 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 45 00 00 00 00 00 00 00 a0 00 01:02:04.573 IDENTIFY DEVICE ef 10 03 02 45 00 00 00 00 00 00 a0 00 01:02:04.573 SET FEATURES [Set transfer mode] Error 7973 [36] occurred at disk power-on lifetime: 10055 hours (418 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 5a 00 00 01 9c cc 99 61 00 Error: UNC at LBA = 0x019ccc99 = 27053209 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 58 00 00 01 9c cc 98 40 08 01:01:56.263 READ FPDMA QUEUED ef 00 10 00 02 a1 9e af 00 00 00 a0 00 01:01:56.262 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:01:56.262 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 45 00 00 00 00 00 00 00 a0 00 01:01:56.262 IDENTIFY DEVICE ef 10 03 02 45 00 00 00 00 00 00 a0 00 01:01:56.262 SET FEATURES [Set transfer mode] Error 7972 [35] occurred at disk power-on lifetime: 10055 hours (418 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 72 00 00 01 9c cc 99 61 00 Error: UNC at LBA = 0x019ccc99 = 27053209 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 70 00 00 01 9c cc 98 40 08 01:01:47.818 READ FPDMA QUEUED ef 00 10 00 02 a1 9e af 00 00 00 a0 00 01:01:47.818 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:01:47.818 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 45 00 00 00 00 00 00 00 a0 00 01:01:47.818 IDENTIFY DEVICE ef 10 03 02 45 00 00 00 00 00 00 a0 00 01:01:47.818 SET FEATURES [Set transfer mode] Error 7971 [34] occurred at disk power-on lifetime: 10055 hours (418 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 22 00 00 01 9c cc 90 61 00 Error: UNC at LBA = 0x019ccc90 = 27053200 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 20 00 00 01 9c cc 90 40 08 01:01:39.451 READ FPDMA QUEUED ef 00 10 00 02 a1 9e af 00 00 00 a0 00 01:01:39.451 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:01:39.451 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 45 00 00 00 00 00 00 00 a0 00 01:01:39.450 IDENTIFY DEVICE ef 10 03 02 45 00 00 00 00 00 00 a0 00 01:01:39.450 SET FEATURES [Set transfer mode] Error 7970 [33] occurred at disk power-on lifetime: 10055 hours (418 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 6a 00 00 01 9c cc 90 61 00 Error: UNC at LBA = 0x019ccc90 = 27053200 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 68 00 00 01 9c cc 90 40 08 01:01:31.039 READ FPDMA QUEUED ef 00 10 00 02 a1 9e af 00 00 00 a0 00 01:01:31.039 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:01:31.038 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 45 00 00 00 00 00 00 00 a0 00 01:01:31.038 IDENTIFY DEVICE ef 10 03 02 45 00 00 00 00 00 00 a0 00 01:01:31.038 SET FEATURES [Set transfer mode] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Interrupted (host reset) 10% 10058 - # 2 Short offline Completed without error 00% 10055 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: --/23 Celsius Lifetime Min/Max Temperature: --/55 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/55 Celsius Min/Max Temperature Limit: 5/55 Celsius Temperature History Size (Index): 478 (306) Index Estimated Time Temperature Celsius 307 2023-01-02 07:39 21 ** ... ..( 5 skipped). .. ** 313 2023-01-02 07:45 21 ** 314 2023-01-02 07:46 22 *** ... ..( 36 skipped). .. *** 351 2023-01-02 08:23 22 *** 352 2023-01-02 08:24 23 **** 353 2023-01-02 08:25 22 *** 354 2023-01-02 08:26 23 **** 355 2023-01-02 08:27 23 **** 356 2023-01-02 08:28 22 *** 357 2023-01-02 08:29 ? - 358 2023-01-02 08:30 23 **** ... ..(109 skipped). .. **** 468 2023-01-02 10:20 23 **** 469 2023-01-02 10:21 ? - 470 2023-01-02 10:22 23 **** ... ..( 32 skipped). .. **** 25 2023-01-02 10:55 23 **** 26 2023-01-02 10:56 24 ***** 27 2023-01-02 10:57 24 ***** 28 2023-01-02 10:58 23 **** 29 2023-01-02 10:59 23 **** 30 2023-01-02 11:00 24 ***** 31 2023-01-02 11:01 ? - 32 2023-01-02 11:02 24 ***** 33 2023-01-02 11:03 ? - 34 2023-01-02 11:04 24 ***** 35 2023-01-02 11:05 25 ****** 36 2023-01-02 11:06 ? - 37 2023-01-02 11:07 ? - 38 2023-01-02 11:08 24 ***** ... ..( 4 skipped). .. ***** 43 2023-01-02 11:13 24 ***** 44 2023-01-02 11:14 25 ****** ... ..( 3 skipped). .. ****** 48 2023-01-02 11:18 25 ****** 49 2023-01-02 11:19 24 ***** ... ..( 5 skipped). .. ***** 55 2023-01-02 11:25 24 ***** 56 2023-01-02 11:26 25 ****** 57 2023-01-02 11:27 ? - 58 2023-01-02 11:28 25 ****** 59 2023-01-02 11:29 25 ****** 60 2023-01-02 11:30 25 ****** 61 2023-01-02 11:31 24 ***** 62 2023-01-02 11:32 24 ***** 63 2023-01-02 11:33 25 ****** 64 2023-01-02 11:34 25 ****** 65 2023-01-02 11:35 26 ******* ... ..( 4 skipped). .. ******* 70 2023-01-02 11:40 26 ******* 71 2023-01-02 11:41 25 ****** 72 2023-01-02 11:42 26 ******* 73 2023-01-02 11:43 26 ******* 74 2023-01-02 11:44 25 ****** ... ..( 2 skipped). .. ****** 77 2023-01-02 11:47 25 ****** 78 2023-01-02 11:48 26 ******* ... ..( 8 skipped). .. ******* 87 2023-01-02 11:57 26 ******* 88 2023-01-02 11:58 25 ****** ... ..( 18 skipped). .. ****** 107 2023-01-02 12:17 25 ****** 108 2023-01-02 12:18 24 ***** 109 2023-01-02 12:19 24 ***** 110 2023-01-02 12:20 25 ****** 111 2023-01-02 12:21 25 ****** 112 2023-01-02 12:22 26 ******* 113 2023-01-02 12:23 25 ****** ... ..( 3 skipped). .. ****** 117 2023-01-02 12:27 25 ****** 118 2023-01-02 12:28 26 ******* 119 2023-01-02 12:29 26 ******* 120 2023-01-02 12:30 25 ****** ... ..( 15 skipped). .. ****** 136 2023-01-02 12:46 25 ****** 137 2023-01-02 12:47 24 ***** ... ..( 4 skipped). .. ***** 142 2023-01-02 12:52 24 ***** 143 2023-01-02 12:53 25 ****** 144 2023-01-02 12:54 24 ***** 145 2023-01-02 12:55 24 ***** 146 2023-01-02 12:56 25 ****** 147 2023-01-02 12:57 ? - 148 2023-01-02 12:58 24 ***** 149 2023-01-02 12:59 24 ***** 150 2023-01-02 13:00 24 ***** 151 2023-01-02 13:01 26 ******* ... ..( 19 skipped). .. ******* 171 2023-01-02 13:21 26 ******* 172 2023-01-02 13:22 25 ****** ... ..( 2 skipped). .. ****** 175 2023-01-02 13:25 25 ****** 176 2023-01-02 13:26 24 ***** 177 2023-01-02 13:27 24 ***** 178 2023-01-02 13:28 24 ***** 179 2023-01-02 13:29 23 **** 180 2023-01-02 13:30 24 ***** ... ..( 3 skipped). .. ***** 184 2023-01-02 13:34 24 ***** 185 2023-01-02 13:35 23 **** ... ..( 12 skipped). .. **** 198 2023-01-02 13:48 23 **** 199 2023-01-02 13:49 22 *** ... ..( 3 skipped). .. *** 203 2023-01-02 13:53 22 *** 204 2023-01-02 13:54 ? - 205 2023-01-02 13:55 18 - 206 2023-01-02 13:56 19 - ... ..( 2 skipped). .. - 209 2023-01-02 13:59 19 - 210 2023-01-02 14:00 20 * ... ..( 2 skipped). .. * 213 2023-01-02 14:03 20 * 214 2023-01-02 14:04 21 ** ... ..( 13 skipped). .. ** 228 2023-01-02 14:18 21 ** 229 2023-01-02 14:19 22 *** ... ..( 2 skipped). .. *** 232 2023-01-02 14:22 22 *** 233 2023-01-02 14:23 21 ** 234 2023-01-02 14:24 21 ** 235 2023-01-02 14:25 21 ** 236 2023-01-02 14:26 22 *** 237 2023-01-02 14:27 22 *** 238 2023-01-02 14:28 22 *** 239 2023-01-02 14:29 21 ** 240 2023-01-02 14:30 21 ** 241 2023-01-02 14:31 21 ** 242 2023-01-02 14:32 22 *** 243 2023-01-02 14:33 21 ** ... ..( 10 skipped). .. ** 254 2023-01-02 14:44 21 ** 255 2023-01-02 14:45 22 *** 256 2023-01-02 14:46 ? - 257 2023-01-02 14:47 22 *** ... ..( 4 skipped). .. *** 262 2023-01-02 14:52 22 *** 263 2023-01-02 14:53 ? - 264 2023-01-02 14:54 22 *** 265 2023-01-02 14:55 23 **** 266 2023-01-02 14:56 22 *** ... ..( 3 skipped). .. *** 270 2023-01-02 15:00 22 *** 271 2023-01-02 15:01 21 ** 272 2023-01-02 15:02 21 ** 273 2023-01-02 15:03 21 ** 274 2023-01-02 15:04 22 *** 275 2023-01-02 15:05 22 *** 276 2023-01-02 15:06 21 ** ... ..( 6 skipped). .. ** 283 2023-01-02 15:13 21 ** 284 2023-01-02 15:14 22 *** 285 2023-01-02 15:15 22 *** 286 2023-01-02 15:16 21 ** ... ..( 4 skipped). .. ** 291 2023-01-02 15:21 21 ** 292 2023-01-02 15:22 22 *** ... ..( 13 skipped). .. *** 306 2023-01-02 15:36 22 *** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 457 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdd smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.0.12-76060006-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: SanDisk SDSSDH3256G Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: X6107000 User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: Not in smartctl database ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jan 2 15:36:23 2023 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 4 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 --- - 0 9 Power_On_Hours -O--CK 100 100 --- - 2822 12 Power_Cycle_Count -O--CK 100 100 --- - 563 165 Unknown_Attribute -O--CK 100 100 --- - 107453023308 166 Unknown_Attribute -O--CK 100 100 --- - 5 167 Unknown_Attribute -O--CK 100 100 --- - 37 168 Unknown_Attribute -O--CK 100 100 --- - 34 169 Unknown_Attribute -O--CK 100 100 --- - 151 170 Unknown_Attribute -O--CK 100 100 --- - 0 171 Unknown_Attribute -O--CK 100 100 --- - 0 172 Unknown_Attribute -O--CK 100 100 --- - 0 173 Unknown_Attribute -O--CK 100 100 --- - 17 174 Unknown_Attribute -O--CK 100 100 --- - 245 184 End-to-End_Error -O--CK 100 100 --- - 0 187 Reported_Uncorrect -O--CK 100 100 --- - 0 188 Command_Timeout -O--CK 100 100 --- - 0 194 Temperature_Celsius -O---K 078 044 --- - 22 (Min/Max 15/44) 199 UDMA_CRC_Error_Count -O--CK 100 100 --- - 0 230 Unknown_SSD_Attribute -O--CK 100 100 --- - 2284943966740 232 Available_Reservd_Space PO--CK 100 100 004 - 100 233 Media_Wearout_Indicator -O--CK 100 100 --- - 4300 234 Unknown_Attribute -O--CK 100 100 --- - 7890 241 Total_LBAs_Written ----CK 253 253 --- - 5643 242 Total_LBAs_Read ----CK 253 253 --- - 6335 244 Unknown_Attribute -O--CK 000 100 --- - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xde GPL VS 8 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 563 --- Lifetime Power-On Resets 0x01 0x010 4 0 --- Power-on Hours 0x01 0x018 6 11835348188 --- Logical Sectors Written 0x01 0x020 6 184712654 --- Number of Write Commands 0x01 0x028 6 13286432492 --- Logical Sectors Read 0x01 0x030 6 269305670 --- Number of Read Commands 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 1 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x000a 4 3 Device-to-host register FISes sent due to a COMRESET