/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.7-desktop-1omv4003] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Crucial/Micron Client SSDs Device Model: CT240BX500SSD1 Serial Number: -- LU WWN Device Id: 5 00a075 ... Firmware Version: M6CR054 User Capacity: 240,057,409,536 bytes [240 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 4 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Feb 17 10:11:59 2022 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 000 - 0 5 Reallocate_NAND_Blk_Cnt -O--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 581 12 Power_Cycle_Count -O--CK 100 100 000 - 654 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Ave_Block-Erase_Count -O--CK 098 098 000 - 26 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 26 180 Unused_Reserve_NAND_Blk PO--CK 100 100 000 - 42 183 SATA_Interfac_Downshift -O--CK 100 100 000 - 0 184 Error_Correction_Count -O--CK 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 076 069 000 - 24 (Min/Max 12/31) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_ECC_Cnt -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 202 Percent_Lifetime_Remain ----CK 098 098 001 - 2 206 Write_Error_Rate -OSR-- 100 100 000 - 0 210 Success_RAIN_Recov_Cnt -O--CK 100 100 000 - 0 246 Total_LBAs_Written -O--CK 100 100 000 - 4317994173 247 Host_Program_Page_Count -O--CK 100 100 000 - 134937317 248 FTL_Program_Page_Count -O--CK 100 100 000 - 49098128 249 Unkn_CrucialMicron_Attr -O--CK 100 100 000 - 0 250 Read_Error_Retry_Rate -O--CK 100 100 000 - 0 251 Unkn_CrucialMicron_Attr -O--CK 100 100 000 - 1724261141 252 Unkn_CrucialMicron_Attr -O--CK 100 100 000 - 0 253 Unkn_CrucialMicron_Attr -O--CK 100 100 000 - 0 254 Unkn_CrucialMicron_Attr -O--CK 100 100 000 - 0 223 Unkn_CrucialMicron_Attr -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 88 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log not supported SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0005 4 1 R_ERR response for non-data FIS 0x000a 4 3 Device-to-host register FISes sent due to a COMRESET /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.7-desktop-1omv4003] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA (AF) Device Model: WDC WD7500BPVT-24HXZT3 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 03.01A03 User Capacity: 750,156,374,016 bytes [750 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Thu Feb 17 10:11:59 2022 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (15660) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 154) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 180 175 021 - 1966 4 Start_Stop_Count -O--CK 095 095 000 - 5348 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 199 000 - 0 9 Power_On_Hours -O--CK 090 090 000 - 7691 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3739 192 Power-Off_Retract_Count -O--CK 200 200 000 - 266 193 Load_Cycle_Count -O--CK 186 186 000 - 44170 194 Temperature_Celsius -O---K 122 081 000 - 25 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 1 198 Offline_Uncorrectable ----CK 200 200 000 - 1 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 1872 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 25 Celsius Power Cycle Min/Max Temperature: 25/27 Celsius Lifetime Min/Max Temperature: 0/66 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (77) Index Estimated Time Temperature Celsius 78 2022-02-17 08:05 28 ********* ... ..( 51 skipped). .. ********* 2 2022-02-17 08:57 28 ********* 3 2022-02-17 08:58 27 ******** ... ..( 64 skipped). .. ******** 68 2022-02-17 10:03 27 ******** 69 2022-02-17 10:04 ? - 70 2022-02-17 10:05 27 ******** 71 2022-02-17 10:06 27 ******** 72 2022-02-17 10:07 27 ******** 73 2022-02-17 10:08 26 ******* 74 2022-02-17 10:09 26 ******* 75 2022-02-17 10:10 26 ******* 76 2022-02-17 10:11 25 ****** 77 2022-02-17 10:12 25 ****** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 503 Vendor specific /dev/sdc smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.7-desktop-1omv4003] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue Serial ATA Device Model: WDC WD1600AAJS-60B4A0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 02.03A02 User Capacity: 160,041,885,696 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Thu Feb 17 10:12:00 2022 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2880) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 38) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 237 3 Spin_Up_Time POS--K 155 154 021 - 3208 4 Start_Stop_Count -O--CK 088 088 000 - 12166 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-K 200 200 051 - 0 9 Power_On_Hours -O--CK 031 031 000 - 50415 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 090 090 000 - 10157 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 093 000 - 70 188 Command_Timeout -O--CK 099 001 000 - 227 190 Airflow_Temperature_Cel -O---K 067 052 040 - 33 192 Power-Off_Retract_Count -O--CK 200 200 000 - 648 193 Load_Cycle_Count -O--CK 196 196 000 - 12166 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 24 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 51 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 51 [2] occurred at disk power-on lifetime: 43742 hours (1822 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 dd 00 71 3a e0 00 Error: UNC 1 sectors at LBA = 0xdd00713a = 3707793722 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 71 dd 3a e0 00 02:28:14.544 READ DMA EXT 25 00 00 00 01 00 00 00 71 dd 39 e0 00 02:28:14.544 READ DMA EXT 25 00 00 00 01 00 00 00 71 dd 38 e0 00 02:28:14.543 READ DMA EXT 25 00 00 00 01 00 00 00 71 dd 37 e0 00 02:28:14.543 READ DMA EXT 25 00 00 00 01 00 00 00 71 dd 36 e0 00 02:28:14.543 READ DMA EXT Error 50 [1] occurred at disk power-on lifetime: 43742 hours (1822 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 40 00 00 dd 00 71 00 e0 00 Error: UNC 64 sectors at LBA = 0xdd007100 = 3707793664 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 00 71 dd 00 e0 00 02:28:11.560 READ DMA EXT 35 00 00 00 10 00 00 00 70 38 18 e0 00 02:28:11.556 WRITE DMA EXT 25 00 00 00 10 00 00 00 1e 05 d8 e0 00 02:28:11.556 READ DMA EXT 35 00 00 00 10 00 00 00 70 33 78 e0 00 02:28:11.553 WRITE DMA EXT 25 00 00 00 10 00 00 00 1e 05 c8 e0 00 02:28:11.552 READ DMA EXT Error 49 [0] occurred at disk power-on lifetime: 43423 hours (1809 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 dd 00 71 38 e0 00 Error: UNC 8 sectors at LBA = 0xdd007138 = 3707793720 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 71 dd 38 e0 00 01:54:58.619 READ DMA EXT 25 00 00 00 08 00 00 00 71 dd 30 e0 00 01:54:58.619 READ DMA EXT 25 00 00 00 08 00 00 00 71 dd 28 e0 00 01:54:58.619 READ DMA EXT 25 00 00 00 08 00 00 00 71 dd 20 e0 00 01:54:58.557 READ DMA EXT 35 00 00 00 08 00 00 00 63 11 f0 e0 00 01:54:58.523 WRITE DMA EXT Error 48 [23] occurred at disk power-on lifetime: 43423 hours (1809 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 dd 00 71 20 e0 00 Error: UNC 32 sectors at LBA = 0xdd007120 = 3707793696 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 00 71 dd 20 e0 00 01:54:55.590 READ DMA EXT 35 00 00 00 18 00 00 00 8e 63 80 e0 00 01:54:55.590 WRITE DMA EXT 25 00 00 00 18 00 00 00 71 dd 20 e0 00 01:54:55.590 READ DMA EXT 35 00 00 00 20 00 00 0a 80 e1 c0 e0 00 01:54:55.590 WRITE DMA EXT 35 00 00 00 20 00 00 00 8e 63 60 e0 00 01:54:55.590 WRITE DMA EXT Error 47 [22] occurred at disk power-on lifetime: 43332 hours (1805 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 dd 00 71 38 e0 00 Error: UNC 8 sectors at LBA = 0xdd007138 = 3707793720 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 71 dd 38 e0 00 01:17:10.527 READ DMA EXT 25 00 00 00 08 00 00 00 71 dd 30 e0 00 01:17:10.527 READ DMA EXT 25 00 00 00 08 00 00 00 71 dd 28 e0 00 01:17:10.465 READ DMA EXT ea 00 00 00 00 5f 02 c7 00 00 00 e0 00 01:17:10.421 FLUSH CACHE EXT 35 00 00 00 08 00 00 00 5f 02 c0 e0 00 01:17:10.421 WRITE DMA EXT Error 46 [21] occurred at disk power-on lifetime: 43332 hours (1805 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 dd 00 71 20 e0 00 Error: UNC 32 sectors at LBA = 0xdd007120 = 3707793696 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 00 71 dd 20 e0 00 01:17:06.886 READ DMA EXT 35 00 00 00 20 00 00 09 19 a4 e0 e0 00 01:17:06.886 WRITE DMA EXT 35 00 00 00 20 00 00 09 19 b7 a0 e0 00 01:17:06.885 WRITE DMA EXT 25 00 00 00 20 00 00 00 03 7c 20 e0 00 01:17:06.870 READ DMA EXT 35 00 00 00 20 00 00 09 19 a4 e0 e0 00 01:17:06.869 WRITE DMA EXT Error 45 [20] occurred at disk power-on lifetime: 43258 hours (1802 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 dd 00 71 38 e0 00 Error: UNC 8 sectors at LBA = 0xdd007138 = 3707793720 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 71 dd 38 e0 00 00:51:50.631 READ DMA EXT 25 00 00 00 08 00 00 00 71 dd 30 e0 00 00:51:50.631 READ DMA EXT 25 00 00 00 08 00 00 00 71 dd 28 e0 00 00:51:50.589 READ DMA EXT 25 00 00 00 08 00 00 00 71 dd 20 e0 00 00:51:50.539 READ DMA EXT 25 00 00 00 20 00 00 00 66 55 a0 e0 00 00:51:50.505 READ DMA EXT Error 44 [19] occurred at disk power-on lifetime: 43258 hours (1802 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 dd 00 71 20 e0 00 Error: UNC 32 sectors at LBA = 0xdd007120 = 3707793696 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 00 71 dd 20 e0 00 00:51:47.088 READ DMA EXT 35 00 00 00 10 00 00 00 75 af a8 e0 00 00:51:47.085 WRITE DMA EXT 25 00 00 00 10 00 00 07 75 26 68 e0 00 00:51:47.082 READ DMA EXT 35 00 00 00 18 00 00 00 75 af 90 e0 00 00:51:47.081 WRITE DMA EXT 25 00 00 00 18 00 00 07 75 1d 80 e0 00 00:51:47.077 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 40423 - # 2 Short offline Completed without error 00% 40422 - # 3 Extended offline Completed without error 00% 40158 - # 4 Short offline Completed without error 00% 40158 - # 5 Extended offline Aborted by host 80% 1 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 33 Celsius Power Cycle Min/Max Temperature: 32/33 Celsius Lifetime Min/Max Temperature: 16/48 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (88) Index Estimated Time Temperature Celsius 89 2022-02-17 08:05 32 ************* ... ..(117 skipped). .. ************* 79 2022-02-17 10:03 32 ************* 80 2022-02-17 10:04 ? - 81 2022-02-17 10:05 32 ************* 82 2022-02-17 10:06 33 ************** ... ..( 5 skipped). .. ************** 88 2022-02-17 10:12 33 ************** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x8000 4 504 Vendor specific /dev/sdd smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.7-desktop-1omv4003] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Indilinx Barefoot based SSDs Device Model: OCZ-VERTEX v1.10 Serial Number: -- Firmware Version: 1370 User Capacity: 64,023,257,088 bytes [64.0 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available, deterministic Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Thu Feb 17 10:12:00 2022 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x1d) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 0) minutes. Extended self-test routine recommended polling time: ( 0) minutes. SMART Attributes Data Structure revision number: 5 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate ------ --- --- --- - 4 9 Power_On_Hours ------ --- --- --- - 19200 12 Power_Cycle_Count ------ --- --- --- - 943 184 Initial_Bad_Block_Count ------ --- --- --- - 15 195 Program_Failure_Blk_Ct ------ --- --- --- - 2 196 Erase_Failure_Blk_Ct ------ --- --- --- - 0 197 Read_Failure_Blk_Ct ------ --- --- --- - 0 198 Read_Sectors_Tot_Ct ------ --- --- --- - 21650699057 199 Write_Sectors_Tot_Ct ------ --- --- --- - 17444166752 200 Read_Commands_Tot_Ct ------ --- --- --- - 358352843 201 Write_Commands_Tot_Ct ------ --- --- --- - 251543644 202 Error_Bits_Flash_Tot_Ct ------ --- --- --- - 1382887065 203 Corr_Read_Errors_Tot_Ct ------ --- --- --- - 2253568050 204 Bad_Block_Full_Flag ------ --- --- --- - 0 205 Max_PE_Count_Spec ------ --- --- --- - 100000 206 Min_Erase_Count ------ --- --- --- - 0 207 Max_Erase_Count ------ --- --- --- - 17814 208 Average_Erase_Count ------ --- --- --- - 38965 209 Remaining_Lifetime_Perc ------ --- --- --- - 62 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 51 Comprehensive SMART error log 0x03 GPL,SL R/O 77 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0xa0 GPL VS 4096 Device vendor specific log Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. SMART Extended Comprehensive Error Log Version: 49 (77 sectors) No Errors Logged Warning! SMART Extended Self-test Log Structure error: invalid SMART checksum. SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) [Reserved: 0x00 0x00 0x51 0x10] ID Size Value Description