/dev/nvme0n1 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-50-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Number: KINGSTON SKC3000D2048G Serial Number: -- Firmware Version: EIFK31.6 PCI Vendor/Subsystem ID: 0x2646 IEEE OUI Identifier: 0x0026b7 Total NVM Capacity: 2,048,408,248,320 [2.04 TB] Unallocated NVM Capacity: 0 Controller ID: 1 NVMe Version: 1.4 Number of Namespaces: 1 Namespace 1 Size/Capacity: 2,048,408,248,320 [2.04 TB] Namespace 1 Formatted LBA Size: 512 Namespace 1 IEEE EUI-64: 0026b7 ... Local Time is: Wed Oct 12 23:29:59 2022 AEDT Firmware Updates (0x12): 1 Slot, no Reset required Optional Admin Commands (0x0017): Security Format Frmw_DL Self_Test Optional NVM Commands (0x005d): Comp DS_Mngmt Wr_Zero Sav/Sel_Feat Timestmp Log Page Attributes (0x08): Telmtry_Lg Maximum Data Transfer Size: 512 Pages Warning Comp. Temp. Threshold: 84 Celsius Critical Comp. Temp. Threshold: 89 Celsius Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 8.80W - - 0 0 0 0 0 0 1 + 7.10W - - 1 1 1 1 0 0 2 + 5.20W - - 2 2 2 2 0 0 3 - 0.0620W - - 3 3 3 3 2500 7500 4 - 0.0620W - - 4 4 4 4 2500 7500 Supported LBA Sizes (NSID 0x1) Id Fmt Data Metadt Rel_Perf 0 + 512 0 2 1 - 4096 0 1 === START OF SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02) Critical Warning: 0x00 Temperature: 23 Celsius Available Spare: 100% Available Spare Threshold: 10% Percentage Used: 0% Data Units Read: 818,232 [418 GB] Data Units Written: 351,733 [180 GB] Host Read Commands: 1,696,726 Host Write Commands: 1,303,016 Controller Busy Time: 6 Power Cycles: 12 Power On Hours: 23 Unsafe Shutdowns: 11 Media and Data Integrity Errors: 0 Error Information Log Entries: 86 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Temperature Sensor 2: 41 Celsius Error Information (NVMe Log 0x01, 16 of 63 entries) Num ErrCount SQId CmdId Status PELoc LBA NSID VS 0 86 0 0x4007 0x4004 0x102c 0 0 - 1 85 0 0x4006 0x4004 0x102c 0 0 - 2 84 0 0x1017 0x4004 0x102c 0 0 - 3 83 0 0x2005 0x4004 0x102c 0 0 - 4 82 0 0x1004 0x4004 0x028 0 0 - 5 81 0 0x2010 0x4004 - 0 0 - /dev/nvme1n1 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-50-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Number: KINGSTON SKC3000D2048G Serial Number: -- Firmware Version: EIFK31.6 PCI Vendor/Subsystem ID: 0x2646 IEEE OUI Identifier: 0x0026b7 Total NVM Capacity: 2,048,408,248,320 [2.04 TB] Unallocated NVM Capacity: 0 Controller ID: 1 NVMe Version: 1.4 Number of Namespaces: 1 Namespace 1 Size/Capacity: 2,048,408,248,320 [2.04 TB] Namespace 1 Formatted LBA Size: 512 Namespace 1 IEEE EUI-64: 0026b7 ... Local Time is: Wed Oct 12 23:29:59 2022 AEDT Firmware Updates (0x12): 1 Slot, no Reset required Optional Admin Commands (0x0017): Security Format Frmw_DL Self_Test Optional NVM Commands (0x005d): Comp DS_Mngmt Wr_Zero Sav/Sel_Feat Timestmp Log Page Attributes (0x08): Telmtry_Lg Maximum Data Transfer Size: 512 Pages Warning Comp. Temp. Threshold: 84 Celsius Critical Comp. Temp. Threshold: 89 Celsius Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 8.80W - - 0 0 0 0 0 0 1 + 7.10W - - 1 1 1 1 0 0 2 + 5.20W - - 2 2 2 2 0 0 3 - 0.0620W - - 3 3 3 3 2500 7500 4 - 0.0620W - - 4 4 4 4 2500 7500 Supported LBA Sizes (NSID 0x1) Id Fmt Data Metadt Rel_Perf 0 + 512 0 2 1 - 4096 0 1 === START OF SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02) Critical Warning: 0x00 Temperature: 20 Celsius Available Spare: 100% Available Spare Threshold: 10% Percentage Used: 0% Data Units Read: 228 [116 MB] Data Units Written: 1 [512 KB] Host Read Commands: 4,341 Host Write Commands: 1 Controller Busy Time: 0 Power Cycles: 12 Power On Hours: 22 Unsafe Shutdowns: 11 Media and Data Integrity Errors: 0 Error Information Log Entries: 86 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Temperature Sensor 2: 43 Celsius Error Information (NVMe Log 0x01, 16 of 63 entries) Num ErrCount SQId CmdId Status PELoc LBA NSID VS 0 86 0 0x4019 0x4004 0x102c 0 0 - 1 85 0 0x4018 0x4004 0x102c 0 0 - 2 84 0 0x2016 0x4004 0x102c 0 0 - 3 83 0 0x2015 0x4004 0x102c 0 0 - 4 82 0 0x1010 0x4004 0x028 0 0 - 5 81 0 0x2018 0x4004 - 0 0 - /dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-50-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Green Device Model: WDC WD20EARX-00PASB0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 51.0AB51 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Oct 12 23:29:59 2022 AEDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (38760) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 374) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 169 164 021 - 6516 4 Start_Stop_Count -O--CK 097 097 000 - 3725 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 050 050 000 - 36814 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3714 192 Power-Off_Retract_Count -O--CK 197 197 000 - 2894 193 Load_Cycle_Count -O--CK 158 158 000 - 128899 194 Temperature_Celsius -O---K 124 110 000 - 26 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 2 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2 [1] occurred at disk power-on lifetime: 3878 hours (161 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 00:35:39.499 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:35:39.499 SMART WRITE LOG ec 00 00 00 01 00 00 00 00 00 00 40 08 00:35:15.813 IDENTIFY DEVICE ec 00 00 00 01 00 00 00 00 00 00 40 08 00:35:10.357 IDENTIFY DEVICE ec 00 00 00 01 00 00 00 00 00 00 00 08 00:34:48.689 IDENTIFY DEVICE Error 1 [0] occurred at disk power-on lifetime: 3878 hours (161 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:35:39.499 SMART WRITE LOG ec 00 00 00 01 00 00 00 00 00 00 40 08 00:35:15.813 IDENTIFY DEVICE ec 00 00 00 01 00 00 00 00 00 00 40 08 00:35:10.357 IDENTIFY DEVICE ec 00 00 00 01 00 00 00 00 00 00 00 08 00:34:48.689 IDENTIFY DEVICE 61 00 08 00 00 00 00 00 00 08 00 40 08 00:34:42.531 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 26 Celsius Power Cycle Min/Max Temperature: 26/27 Celsius Lifetime Min/Max Temperature: 14/40 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (392) Index Estimated Time Temperature Celsius 393 2022-10-12 15:33 24 ***** ... ..( 5 skipped). .. ***** 399 2022-10-12 15:39 24 ***** 400 2022-10-12 15:40 25 ****** 401 2022-10-12 15:41 25 ****** 402 2022-10-12 15:42 24 ***** 403 2022-10-12 15:43 24 ***** 404 2022-10-12 15:44 ? - 405 2022-10-12 15:45 15 - 406 2022-10-12 15:46 15 - 407 2022-10-12 15:47 16 - 408 2022-10-12 15:48 16 - 409 2022-10-12 15:49 16 - 410 2022-10-12 15:50 17 - ... ..( 3 skipped). .. - 414 2022-10-12 15:54 17 - 415 2022-10-12 15:55 18 - ... ..( 5 skipped). .. - 421 2022-10-12 16:01 18 - 422 2022-10-12 16:02 19 - 423 2022-10-12 16:03 19 - 424 2022-10-12 16:04 19 - 425 2022-10-12 16:05 20 * ... ..( 2 skipped). .. * 428 2022-10-12 16:08 20 * 429 2022-10-12 16:09 21 ** ... ..( 14 skipped). .. ** 444 2022-10-12 16:24 21 ** 445 2022-10-12 16:25 22 *** ... ..( 18 skipped). .. *** 464 2022-10-12 16:44 22 *** 465 2022-10-12 16:45 23 **** ... ..( 10 skipped). .. **** 476 2022-10-12 16:56 23 **** 477 2022-10-12 16:57 22 *** ... ..( 46 skipped). .. *** 46 2022-10-12 17:44 22 *** 47 2022-10-12 17:45 ? - 48 2022-10-12 17:46 15 - 49 2022-10-12 17:47 ? - 50 2022-10-12 17:48 15 - 51 2022-10-12 17:49 ? - 52 2022-10-12 17:50 17 - 53 2022-10-12 17:51 ? - 54 2022-10-12 17:52 18 - 55 2022-10-12 17:53 ? - 56 2022-10-12 17:54 18 - 57 2022-10-12 17:55 ? - 58 2022-10-12 17:56 25 ****** 59 2022-10-12 17:57 ? - 60 2022-10-12 17:58 22 *** 61 2022-10-12 17:59 ? - 62 2022-10-12 18:00 15 - 63 2022-10-12 18:01 ? - 64 2022-10-12 18:02 18 - 65 2022-10-12 18:03 ? - 66 2022-10-12 18:04 27 ******** 67 2022-10-12 18:05 26 ******* 68 2022-10-12 18:06 26 ******* 69 2022-10-12 18:07 27 ******** ... ..( 3 skipped). .. ******** 73 2022-10-12 18:11 27 ******** 74 2022-10-12 18:12 26 ******* 75 2022-10-12 18:13 26 ******* 76 2022-10-12 18:14 ? - 77 2022-10-12 18:15 26 ******* ... ..( 37 skipped). .. ******* 115 2022-10-12 18:53 26 ******* 116 2022-10-12 18:54 ? - 117 2022-10-12 18:55 27 ******** 118 2022-10-12 18:56 26 ******* ... ..( 11 skipped). .. ******* 130 2022-10-12 19:08 26 ******* 131 2022-10-12 19:09 22 *** 132 2022-10-12 19:10 22 *** 133 2022-10-12 19:11 22 *** 134 2022-10-12 19:12 23 **** ... ..( 12 skipped). .. **** 147 2022-10-12 19:25 23 **** 148 2022-10-12 19:26 24 ***** ... ..( 12 skipped). .. ***** 161 2022-10-12 19:39 24 ***** 162 2022-10-12 19:40 25 ****** ... ..( 58 skipped). .. ****** 221 2022-10-12 20:39 25 ****** 222 2022-10-12 20:40 ? - 223 2022-10-12 20:41 18 - ... ..( 4 skipped). .. - 228 2022-10-12 20:46 18 - 229 2022-10-12 20:47 19 - 230 2022-10-12 20:48 19 - 231 2022-10-12 20:49 20 * ... ..( 2 skipped). .. * 234 2022-10-12 20:52 20 * 235 2022-10-12 20:53 21 ** ... ..( 5 skipped). .. ** 241 2022-10-12 20:59 21 ** 242 2022-10-12 21:00 22 *** ... ..( 12 skipped). .. *** 255 2022-10-12 21:13 22 *** 256 2022-10-12 21:14 23 **** ... ..( 7 skipped). .. **** 264 2022-10-12 21:22 23 **** 265 2022-10-12 21:23 24 ***** ... ..( 16 skipped). .. ***** 282 2022-10-12 21:40 24 ***** 283 2022-10-12 21:41 25 ****** 284 2022-10-12 21:42 24 ***** ... ..( 6 skipped). .. ***** 291 2022-10-12 21:49 24 ***** 292 2022-10-12 21:50 25 ****** 293 2022-10-12 21:51 24 ***** 294 2022-10-12 21:52 24 ***** 295 2022-10-12 21:53 25 ****** ... ..( 3 skipped). .. ****** 299 2022-10-12 21:57 25 ****** 300 2022-10-12 21:58 24 ***** 301 2022-10-12 21:59 25 ****** ... ..( 40 skipped). .. ****** 342 2022-10-12 22:40 25 ****** 343 2022-10-12 22:41 ? - 344 2022-10-12 22:42 18 - ... ..( 4 skipped). .. - 349 2022-10-12 22:47 18 - 350 2022-10-12 22:48 19 - 351 2022-10-12 22:49 19 - 352 2022-10-12 22:50 19 - 353 2022-10-12 22:51 20 * 354 2022-10-12 22:52 20 * 355 2022-10-12 22:53 21 ** ... ..( 5 skipped). .. ** 361 2022-10-12 22:59 21 ** 362 2022-10-12 23:00 22 *** ... ..( 9 skipped). .. *** 372 2022-10-12 23:10 22 *** 373 2022-10-12 23:11 23 **** ... ..( 8 skipped). .. **** 382 2022-10-12 23:20 23 **** 383 2022-10-12 23:21 24 ***** ... ..( 8 skipped). .. ***** 392 2022-10-12 23:30 24 ***** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 793 Vendor specific /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-50-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SandForce Driven SSDs Device Model: OCZ-VERTEX3 Serial Number: -- LU WWN Device Id: 5 e83a97 ... Firmware Version: 2.22 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available, deterministic Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS, ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Oct 12 23:30:00 2022 AEDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Disabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 48) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0021) SCT Status supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 120 120 050 - 0/0 5 Retired_Block_Count PO--CK 100 100 003 - 0 9 Power_On_Hours_and_Msec -O--CK 000 000 000 - 34659h+42m+17.380s 12 Power_Cycle_Count -O--CK 097 097 000 - 3110 171 Program_Fail_Count -O--CK 000 000 000 - 0 172 Erase_Fail_Count -O--CK 000 000 000 - 0 174 Unexpect_Power_Loss_Ct ----CK 000 000 000 - 152 177 Wear_Range_Delta ------ 000 000 000 - 7 181 Program_Fail_Count -O--CK 000 000 000 - 0 182 Erase_Fail_Count -O--CK 000 000 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 030 030 000 - 30 (Min/Max 30/30) 195 ECC_Uncorr_Error_Count --SRC- 100 100 000 - 0/0 196 Reallocated_Event_Count PO--CK 100 100 003 - 0 201 Unc_Soft_Read_Err_Rate --SRC- 100 100 000 - 0/0 204 Soft_ECC_Correct_Rate --SRC- 100 100 000 - 0/0 230 Life_Curve_Status PO--C- 100 100 000 - 100 231 SSD_Life_Left PO--C- 100 100 010 - 0 233 SandForce_Internal ------ 000 000 000 - 4641 234 SandForce_Internal -O--CK 000 000 000 - 4157 241 Lifetime_Writes_GiB -O--CK 000 000 000 - 4157 242 Lifetime_Reads_GiB -O--CK 000 000 000 - 5561 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xb7 GPL,SL VS 16 Device vendor specific log 0xd0 GPL VS 65535 Device vendor specific log 0xd0 SL VS 255 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log not supported SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 0 (0x0000) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 30/30 Celsius Lifetime Min/Max Temperature: 30/30 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: ?/ ? Celsius Min/Max Temperature Limit: ?/ ? Celsius Temperature History Size (Index): 478 (2) Index Estimated Time Temperature Celsius 3 2022-10-09 16:00 ? - ... ..(476 skipped). .. - 2 2022-10-12 23:30 ? - SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x0002 2 0 R_ERR response for data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdc smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-50-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Green Device Model: WDC WD20EARX-00PASB0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 51.0AB51 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Oct 12 23:30:00 2022 AEDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (36660) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 354) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 173 166 021 - 6350 4 Start_Stop_Count -O--CK 097 097 000 - 3727 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 049 049 000 - 37719 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3714 192 Power-Off_Retract_Count -O--CK 197 197 000 - 2890 193 Load_Cycle_Count -O--CK 028 028 000 - 516808 194 Temperature_Celsius -O---K 124 111 000 - 26 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Aborted by host 90% 678 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 26 Celsius Power Cycle Min/Max Temperature: 26/26 Celsius Lifetime Min/Max Temperature: 16/39 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (243) Index Estimated Time Temperature Celsius 244 2022-10-12 15:33 24 ***** ... ..( 3 skipped). .. ***** 248 2022-10-12 15:37 24 ***** 249 2022-10-12 15:38 25 ****** 250 2022-10-12 15:39 24 ***** 251 2022-10-12 15:40 24 ***** 252 2022-10-12 15:41 25 ****** 253 2022-10-12 15:42 25 ****** 254 2022-10-12 15:43 24 ***** 255 2022-10-12 15:44 24 ***** 256 2022-10-12 15:45 25 ****** ... ..( 5 skipped). .. ****** 262 2022-10-12 15:51 25 ****** 263 2022-10-12 15:52 26 ******* ... ..( 18 skipped). .. ******* 282 2022-10-12 16:11 26 ******* 283 2022-10-12 16:12 27 ******** 284 2022-10-12 16:13 26 ******* ... ..( 6 skipped). .. ******* 291 2022-10-12 16:20 26 ******* 292 2022-10-12 16:21 25 ****** ... ..( 6 skipped). .. ****** 299 2022-10-12 16:28 25 ****** 300 2022-10-12 16:29 ? - 301 2022-10-12 16:30 16 - ... ..( 2 skipped). .. - 304 2022-10-12 16:33 16 - 305 2022-10-12 16:34 17 - 306 2022-10-12 16:35 17 - 307 2022-10-12 16:36 18 - ... ..( 2 skipped). .. - 310 2022-10-12 16:39 18 - 311 2022-10-12 16:40 19 - 312 2022-10-12 16:41 20 * 313 2022-10-12 16:42 20 * 314 2022-10-12 16:43 20 * 315 2022-10-12 16:44 21 ** ... ..( 2 skipped). .. ** 318 2022-10-12 16:47 21 ** 319 2022-10-12 16:48 22 *** ... ..( 9 skipped). .. *** 329 2022-10-12 16:58 22 *** 330 2022-10-12 16:59 23 **** ... ..( 5 skipped). .. **** 336 2022-10-12 17:05 23 **** 337 2022-10-12 17:06 24 ***** ... ..( 2 skipped). .. ***** 340 2022-10-12 17:09 24 ***** 341 2022-10-12 17:10 23 **** ... ..( 4 skipped). .. **** 346 2022-10-12 17:15 23 **** 347 2022-10-12 17:16 24 ***** 348 2022-10-12 17:17 23 **** ... ..( 9 skipped). .. **** 358 2022-10-12 17:27 23 **** 359 2022-10-12 17:28 22 *** 360 2022-10-12 17:29 22 *** 361 2022-10-12 17:30 23 **** 362 2022-10-12 17:31 22 *** ... ..( 5 skipped). .. *** 368 2022-10-12 17:37 22 *** 369 2022-10-12 17:38 23 **** 370 2022-10-12 17:39 22 *** ... ..( 13 skipped). .. *** 384 2022-10-12 17:53 22 *** 385 2022-10-12 17:54 23 **** ... ..( 17 skipped). .. **** 403 2022-10-12 18:12 23 **** 404 2022-10-12 18:13 22 *** 405 2022-10-12 18:14 22 *** 406 2022-10-12 18:15 23 **** 407 2022-10-12 18:16 22 *** 408 2022-10-12 18:17 23 **** ... ..( 2 skipped). .. **** 411 2022-10-12 18:20 23 **** 412 2022-10-12 18:21 22 *** 413 2022-10-12 18:22 23 **** ... ..( 4 skipped). .. **** 418 2022-10-12 18:27 23 **** 419 2022-10-12 18:28 24 ***** 420 2022-10-12 18:29 24 ***** 421 2022-10-12 18:30 24 ***** 422 2022-10-12 18:31 23 **** ... ..( 2 skipped). .. **** 425 2022-10-12 18:34 23 **** 426 2022-10-12 18:35 ? - 427 2022-10-12 18:36 16 - 428 2022-10-12 18:37 ? - 429 2022-10-12 18:38 15 - 430 2022-10-12 18:39 ? - 431 2022-10-12 18:40 17 - 432 2022-10-12 18:41 ? - 433 2022-10-12 18:42 18 - 434 2022-10-12 18:43 ? - 435 2022-10-12 18:44 18 - 436 2022-10-12 18:45 ? - 437 2022-10-12 18:46 25 ****** 438 2022-10-12 18:47 ? - 439 2022-10-12 18:48 23 **** 440 2022-10-12 18:49 ? - 441 2022-10-12 18:50 15 - 442 2022-10-12 18:51 ? - 443 2022-10-12 18:52 18 - 444 2022-10-12 18:53 ? - 445 2022-10-12 18:54 27 ******** 446 2022-10-12 18:55 26 ******* ... ..( 7 skipped). .. ******* 454 2022-10-12 19:03 26 ******* 455 2022-10-12 19:04 ? - 456 2022-10-12 19:05 26 ******* 457 2022-10-12 19:06 25 ****** ... ..( 24 skipped). .. ****** 4 2022-10-12 19:31 25 ****** 5 2022-10-12 19:32 26 ******* ... ..( 10 skipped). .. ******* 16 2022-10-12 19:43 26 ******* 17 2022-10-12 19:44 ? - 18 2022-10-12 19:45 26 ******* ... ..( 12 skipped). .. ******* 31 2022-10-12 19:58 26 ******* 32 2022-10-12 19:59 24 ***** ... ..( 8 skipped). .. ***** 41 2022-10-12 20:08 24 ***** 42 2022-10-12 20:09 25 ****** 43 2022-10-12 20:10 24 ***** ... ..( 5 skipped). .. ***** 49 2022-10-12 20:16 24 ***** 50 2022-10-12 20:17 25 ****** 51 2022-10-12 20:18 24 ***** ... ..( 10 skipped). .. ***** 62 2022-10-12 20:29 24 ***** 63 2022-10-12 20:30 23 **** 64 2022-10-12 20:31 24 ***** ... ..( 5 skipped). .. ***** 70 2022-10-12 20:37 24 ***** 71 2022-10-12 20:38 ? - 72 2022-10-12 20:39 18 - 73 2022-10-12 20:40 18 - 74 2022-10-12 20:41 18 - 75 2022-10-12 20:42 19 - 76 2022-10-12 20:43 20 * 77 2022-10-12 20:44 19 - 78 2022-10-12 20:45 20 * ... ..( 2 skipped). .. * 81 2022-10-12 20:48 20 * 82 2022-10-12 20:49 21 ** 83 2022-10-12 20:50 21 ** 84 2022-10-12 20:51 22 *** 85 2022-10-12 20:52 22 *** 86 2022-10-12 20:53 22 *** 87 2022-10-12 20:54 23 **** ... ..( 10 skipped). .. **** 98 2022-10-12 21:05 23 **** 99 2022-10-12 21:06 24 ***** 100 2022-10-12 21:07 25 ****** 101 2022-10-12 21:08 24 ***** 102 2022-10-12 21:09 25 ****** 103 2022-10-12 21:10 25 ****** 104 2022-10-12 21:11 24 ***** ... ..( 26 skipped). .. ***** 131 2022-10-12 21:38 24 ***** 132 2022-10-12 21:39 25 ****** 133 2022-10-12 21:40 24 ***** 134 2022-10-12 21:41 24 ***** 135 2022-10-12 21:42 24 ***** 136 2022-10-12 21:43 25 ****** 137 2022-10-12 21:44 24 ***** ... ..( 27 skipped). .. ***** 165 2022-10-12 22:12 24 ***** 166 2022-10-12 22:13 26 ******* ... ..( 3 skipped). .. ******* 170 2022-10-12 22:17 26 ******* 171 2022-10-12 22:18 25 ****** ... ..( 16 skipped). .. ****** 188 2022-10-12 22:35 25 ****** 189 2022-10-12 22:36 24 ***** 190 2022-10-12 22:37 25 ****** 191 2022-10-12 22:38 25 ****** 192 2022-10-12 22:39 ? - 193 2022-10-12 22:40 19 - 194 2022-10-12 22:41 18 - 195 2022-10-12 22:42 19 - 196 2022-10-12 22:43 20 * 197 2022-10-12 22:44 20 * 198 2022-10-12 22:45 21 ** 199 2022-10-12 22:46 21 ** 200 2022-10-12 22:47 22 *** 201 2022-10-12 22:48 21 ** 202 2022-10-12 22:49 21 ** 203 2022-10-12 22:50 22 *** ... ..( 3 skipped). .. *** 207 2022-10-12 22:54 22 *** 208 2022-10-12 22:55 23 **** 209 2022-10-12 22:56 22 *** 210 2022-10-12 22:57 23 **** ... ..( 3 skipped). .. **** 214 2022-10-12 23:01 23 **** 215 2022-10-12 23:02 24 ***** 216 2022-10-12 23:03 24 ***** 217 2022-10-12 23:04 24 ***** 218 2022-10-12 23:05 23 **** ... ..( 4 skipped). .. **** 223 2022-10-12 23:10 23 **** 224 2022-10-12 23:11 25 ****** 225 2022-10-12 23:12 24 ***** 226 2022-10-12 23:13 23 **** 227 2022-10-12 23:14 24 ***** ... ..( 5 skipped). .. ***** 233 2022-10-12 23:20 24 ***** 234 2022-10-12 23:21 23 **** 235 2022-10-12 23:22 24 ***** 236 2022-10-12 23:23 24 ***** 237 2022-10-12 23:24 24 ***** 238 2022-10-12 23:25 25 ****** 239 2022-10-12 23:26 24 ***** 240 2022-10-12 23:27 24 ***** 241 2022-10-12 23:28 24 ***** 242 2022-10-12 23:29 23 **** 243 2022-10-12 23:30 24 ***** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 794 Vendor specific /dev/sdd smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-50-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SandForce Driven SSDs Device Model: OCZ-VERTEX3 Serial Number: -- LU WWN Device Id: 5 e83a97 ... Firmware Version: 2.22 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available, deterministic Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS, ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Oct 12 23:30:00 2022 AEDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Disabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 48) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0021) SCT Status supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 120 120 050 - 0/0 5 Retired_Block_Count PO--CK 100 100 003 - 0 9 Power_On_Hours_and_Msec -O--CK 000 000 000 - 35146h+07m+56.540s 12 Power_Cycle_Count -O--CK 097 097 000 - 3111 171 Program_Fail_Count -O--CK 000 000 000 - 0 172 Erase_Fail_Count -O--CK 000 000 000 - 0 174 Unexpect_Power_Loss_Ct ----CK 000 000 000 - 255 177 Wear_Range_Delta ------ 000 000 000 - 8 181 Program_Fail_Count -O--CK 000 000 000 - 0 182 Erase_Fail_Count -O--CK 000 000 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 030 030 000 - 30 (Min/Max 30/30) 195 ECC_Uncorr_Error_Count --SRC- 100 100 000 - 0/0 196 Reallocated_Event_Count PO--CK 100 100 003 - 0 201 Unc_Soft_Read_Err_Rate --SRC- 100 100 000 - 0/0 204 Soft_ECC_Correct_Rate --SRC- 100 100 000 - 0/0 230 Life_Curve_Status PO--C- 100 100 000 - 100 231 SSD_Life_Left PO--C- 096 096 010 - 0 233 SandForce_Internal ------ 000 000 000 - 27452 234 SandForce_Internal -O--CK 000 000 000 - 28215 241 Lifetime_Writes_GiB -O--CK 000 000 000 - 28215 242 Lifetime_Reads_GiB -O--CK 000 000 000 - 25919 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xb7 GPL,SL VS 16 Device vendor specific log 0xd0 GPL VS 65535 Device vendor specific log 0xd0 SL VS 255 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log not supported SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 0 (0x0000) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 30/30 Celsius Lifetime Min/Max Temperature: 30/30 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: ?/ ? Celsius Min/Max Temperature Limit: ?/ ? Celsius Temperature History Size (Index): 478 (10) Index Estimated Time Temperature Celsius 11 2022-10-09 16:00 ? - ... ..(476 skipped). .. - 10 2022-10-12 23:30 ? - SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x0002 2 0 R_ERR response for data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS