/dev/sda === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Travelstar 5K750 Device Model: Hitachi HTS547550A9E384 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: JE3OA50A User Capacity: 500 107 862 016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Mon May 15 23:13:20 2017 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 135) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 65536 2 Throughput_Performance P-S--- 198 198 040 - 142 3 Spin_Up_Time POS--- 192 192 033 - 0 4 Start_Stop_Count -O--C- 092 092 000 - 13803 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 117 117 040 - 33 9 Power_On_Hours -O--C- 084 084 000 - 7378 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 4362 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 65536 192 Power-Off_Retract_Count -O--CK 099 099 000 - 296 193 Load_Cycle_Count -O--C- 057 057 000 - 431532 194 Temperature_Celsius -O---- 146 146 000 - 41 (Min/Max 2/56) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 7213 - # 2 Extended offline Completed without error 00% 6793 - # 3 Short offline Completed without error 00% 6661 - # 4 Extended offline Interrupted (host reset) 40% 6421 - # 5 Extended offline Interrupted (host reset) 90% 6180 - # 6 Extended offline Completed without error 00% 5608 - # 7 Extended offline Interrupted (host reset) 50% 5153 - # 8 Extended offline Completed without error 00% 4930 - # 9 Extended offline Completed without error 00% 4886 - #10 Extended offline Completed without error 00% 4736 - #11 Extended offline Completed without error 00% 4678 - #12 Extended offline Completed without error 00% 4643 - #13 Extended offline Completed without error 00% 3895 - #14 Extended offline Completed without error 00% 3652 - #15 Extended offline Completed without error 00% 3466 - #16 Extended offline Completed without error 00% 3377 - #17 Extended offline Aborted by host 90% 3227 - #18 Short offline Completed without error 00% 3227 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: 37/41 Celsius Lifetime Min/Max Temperature: 2/56 Celsius Lifetime Average Temperature: 40 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (45) Index Estimated Time Temperature Celsius 46 2017-05-15 21:06 49 ****************************** 47 2017-05-15 21:07 48 ***************************** ... ..( 3 skipped). .. ***************************** 51 2017-05-15 21:11 48 ***************************** 52 2017-05-15 21:12 49 ****************************** ... ..( 26 skipped). .. ****************************** 79 2017-05-15 21:39 49 ****************************** 80 2017-05-15 21:40 48 ***************************** ... ..( 5 skipped). .. ***************************** 86 2017-05-15 21:46 48 ***************************** 87 2017-05-15 21:47 47 **************************** ... ..( 32 skipped). .. **************************** 120 2017-05-15 22:20 47 **************************** 121 2017-05-15 22:21 46 *************************** ... ..( 2 skipped). .. *************************** 124 2017-05-15 22:24 46 *************************** 125 2017-05-15 22:25 45 ************************** ... ..( 6 skipped). .. ************************** 4 2017-05-15 22:32 45 ************************** 5 2017-05-15 22:33 46 *************************** ... ..( 5 skipped). .. *************************** 11 2017-05-15 22:39 46 *************************** 12 2017-05-15 22:40 47 **************************** ... ..( 16 skipped). .. **************************** 29 2017-05-15 22:57 47 **************************** 30 2017-05-15 22:58 48 ***************************** ... ..( 4 skipped). .. ***************************** 35 2017-05-15 23:03 48 ***************************** 36 2017-05-15 23:04 ? - 37 2017-05-15 23:05 26 ******* 38 2017-05-15 23:06 ? - 39 2017-05-15 23:07 37 ****************** 40 2017-05-15 23:08 39 ******************** 41 2017-05-15 23:09 39 ******************** 42 2017-05-15 23:10 40 ********************* 43 2017-05-15 23:11 40 ********************* 44 2017-05-15 23:12 41 ********************** 45 2017-05-15 23:13 41 ********************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 4362 --- Lifetime Power-On Resets 0x01 0x010 4 7378 --- Power-on Hours 0x01 0x018 6 16913447315 --- Logical Sectors Written 0x01 0x020 6 145231173 --- Number of Write Commands 0x01 0x028 6 54401775655 --- Logical Sectors Read 0x01 0x030 6 281762326 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 6688 --- Spindle Motor Power-on Hours 0x03 0x010 4 6655 --- Head Flying Hours 0x03 0x018 4 431532 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 2665 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 7352 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 41 --- Current Temperature 0x05 0x010 1 41 N-- Average Short Term Temperature 0x05 0x018 1 40 N-- Average Long Term Temperature 0x05 0x020 1 56 --- Highest Temperature 0x05 0x028 1 2 --- Lowest Temperature 0x05 0x030 1 46 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 43 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 143192 --- Number of Hardware Resets 0x06 0x010 4 6244 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdb === START OF INFORMATION SECTION === Model Family: Western Digital Black Device Model: WDC WD3200BEKT-60F3T1 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 12.01A12 User Capacity: 320 072 933 376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Mon May 15 23:13:22 2017 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 120 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7980) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 95) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 199 199 051 - 16808 3 Spin_Up_Time POS--K 185 173 021 - 1708 4 Start_Stop_Count -O--CK 088 088 000 - 12352 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-K 100 253 051 - 0 9 Power_On_Hours -O--CK 089 089 000 - 8281 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2267 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 099 001 000 - 9468 188 Command_Timeout -O--CK 100 091 000 - 81605623835 190 Airflow_Temperature_Cel -O---K 069 043 040 - 31 191 G-Sense_Error_Rate -O--CK 023 023 000 - 77 192 Power-Off_Retract_Count -O--CK 200 200 000 - 395 193 Load_Cycle_Count -O--CK 189 189 000 - 33588 194 Temperature_Celsius -O---K 116 090 000 - 31 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 175 172 000 - 1353 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 2 200 Multi_Zone_Error_Rate P--R-- 200 200 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 315 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 315 [2] occurred at disk power-on lifetime: 8043 hours (335 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 02 00 0b c4 00 db fe 40 00 Error: IDNF at LBA = 0xbc400dbfe = 50533030910 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 08 00 00 d0 00 00 0b e4 9f f8 40 08 00:08:23.901 WRITE FPDMA QUEUED 61 08 00 00 c8 00 00 0b e4 97 f8 40 08 00:08:23.901 WRITE FPDMA QUEUED 61 08 00 00 c0 00 00 0b db dd e0 40 08 00:08:23.901 WRITE FPDMA QUEUED 61 08 00 00 b8 00 00 0b db d5 e0 40 08 00:08:23.901 WRITE FPDMA QUEUED 61 02 b0 00 b0 00 00 0b db d3 30 40 08 00:08:23.900 WRITE FPDMA QUEUED Error 314 [1] occurred at disk power-on lifetime: 7875 hours (328 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 08 00 00 76 40 00 Error: UNC at LBA = 0x08000076 = 134217846 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 90 00 00 00 00 08 08 40 08 00:02:05.400 READ FPDMA QUEUED 60 00 02 00 88 00 00 00 00 08 00 40 08 00:02:05.400 READ FPDMA QUEUED 60 00 04 00 80 00 00 00 00 08 04 40 08 00:02:05.400 READ FPDMA QUEUED 60 00 02 00 78 00 00 00 00 08 02 40 08 00:02:05.392 READ FPDMA QUEUED 60 00 08 00 70 00 00 00 00 08 78 40 08 00:02:04.554 READ FPDMA QUEUED Error 313 [0] occurred at disk power-on lifetime: 7875 hours (328 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 4f 00 00 08 00 00 9c 40 00 Error: UNC at LBA = 0x0800009c = 134217884 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 c0 00 00 00 00 08 98 40 08 00:01:57.804 READ FPDMA QUEUED ec 00 00 00 01 00 00 00 00 00 00 00 08 00:01:57.801 IDENTIFY DEVICE 60 00 08 00 98 00 00 00 00 08 90 40 08 00:01:55.306 READ FPDMA QUEUED ec 00 00 00 01 00 00 00 00 00 00 00 08 00:01:55.303 IDENTIFY DEVICE 60 00 08 00 78 00 00 00 00 08 88 40 08 00:01:52.449 READ FPDMA QUEUED Error 312 [23] occurred at disk power-on lifetime: 7875 hours (328 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 08 00 00 8e 40 00 Error: UNC at LBA = 0x0800008e = 134217870 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 98 00 00 00 00 08 60 40 08 00:01:36.003 READ FPDMA QUEUED 60 00 40 00 90 00 00 00 00 08 20 40 08 00:01:36.003 READ FPDMA QUEUED 60 00 20 00 88 00 00 00 00 08 00 40 08 00:01:35.912 READ FPDMA QUEUED 60 00 08 00 68 00 00 00 00 00 00 40 08 00:01:35.902 READ FPDMA QUEUED 60 00 08 00 60 00 00 00 00 18 00 40 08 00:01:35.898 READ FPDMA QUEUED Error 311 [22] occurred at disk power-on lifetime: 7875 hours (328 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 6f 00 00 08 00 00 95 40 00 Error: UNC at LBA = 0x08000095 = 134217877 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 40 00 00 00 00 08 90 40 08 00:01:32.072 READ FPDMA QUEUED b0 00 d5 00 01 00 00 00 c2 4f 06 00 08 00:01:32.071 SMART READ LOG 60 00 08 00 08 00 00 00 00 08 88 40 08 00:01:29.919 READ FPDMA QUEUED b0 00 d0 00 01 00 00 00 c2 4f 00 00 08 00:01:29.913 SMART READ DATA 60 00 08 00 d0 00 00 00 00 08 80 40 08 00:01:27.155 READ FPDMA QUEUED Error 310 [21] occurred at disk power-on lifetime: 7875 hours (328 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 08 00 00 9c 40 00 Error: UNC at LBA = 0x0800009c = 134217884 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 90 00 88 00 00 00 00 08 80 40 08 00:01:13.925 READ FPDMA QUEUED 60 00 38 00 80 00 00 00 00 08 40 40 08 00:01:13.925 READ FPDMA QUEUED 60 00 08 00 78 00 00 00 00 08 10 40 08 00:01:13.924 READ FPDMA QUEUED 60 00 18 00 70 00 00 00 00 08 20 40 08 00:01:13.924 READ FPDMA QUEUED 60 00 08 00 68 00 00 00 00 08 78 40 08 00:01:13.517 READ FPDMA QUEUED Error 309 [20] occurred at disk power-on lifetime: 7875 hours (328 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 08 00 00 9c 40 00 Error: UNC at LBA = 0x0800009c = 134217884 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 18 00 00 00 00 08 98 40 08 00:01:10.374 READ FPDMA QUEUED b0 00 d5 00 01 00 00 00 c2 4f 00 00 08 00:01:10.373 SMART READ LOG 60 00 08 00 f0 00 00 00 00 08 90 40 08 00:01:08.168 READ FPDMA QUEUED b0 00 db 00 f8 00 00 00 c2 4f 00 00 08 00:01:08.158 SMART EN/DISABLE AUTO OFFLINE [NS (SFF-8035i)] 60 00 08 00 c8 00 00 00 00 08 88 40 08 00:01:05.532 READ FPDMA QUEUED Error 308 [19] occurred at disk power-on lifetime: 7875 hours (328 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 08 00 00 9c 40 00 Error: UNC at LBA = 0x0800009c = 134217884 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 90 00 18 00 00 00 00 08 80 40 08 00:00:50.637 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:50.637 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:50.634 IDENTIFY DEVICE ef 00 03 00 45 00 00 00 00 00 00 a0 08 00:00:50.634 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:50.632 SET FEATURES [Enable SATA feature] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 90% 8271 188701401 # 2 Extended offline Completed: read failure 90% 8196 188701401 # 3 Extended offline Completed: read failure 90% 8135 195310753 # 4 Extended offline Completed: read failure 90% 8023 188701401 # 5 Extended offline Completed: read failure 90% 7877 195310732 # 6 Extended offline Interrupted (host reset) 90% 6510 - # 7 Extended offline Interrupted (host reset) 90% 6450 - # 8 Extended offline Completed without error 00% 6190 - # 9 Extended offline Completed without error 00% 5461 - #10 Extended offline Completed without error 00% 5160 - #11 Extended offline Interrupted (host reset) 50% 4637 - #12 Extended offline Completed without error 00% 4594 - #13 Extended offline Interrupted (host reset) 10% 4537 - #14 Extended offline Completed without error 00% 4444 - #15 Extended offline Interrupted (host reset) 90% 4289 - #16 Extended offline Completed without error 00% 3933 - #17 Extended offline Completed without error 00% 3718 - #18 Extended offline Completed without error 00% 3644 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 30/31 Celsius Lifetime Min/Max Temperature: 26/57 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (3) Index Estimated Time Temperature Celsius 4 2017-05-15 21:06 33 ************** 5 2017-05-15 21:07 33 ************** 6 2017-05-15 21:08 ? - 7 2017-05-15 21:09 33 ************** 8 2017-05-15 21:10 ? - 9 2017-05-15 21:11 34 *************** 10 2017-05-15 21:12 33 ************** 11 2017-05-15 21:13 34 *************** ... ..( 21 skipped). .. *************** 33 2017-05-15 21:35 34 *************** 34 2017-05-15 21:36 ? - 35 2017-05-15 21:37 34 *************** 36 2017-05-15 21:38 34 *************** 37 2017-05-15 21:39 ? - 38 2017-05-15 21:40 34 *************** 39 2017-05-15 21:41 34 *************** 40 2017-05-15 21:42 ? - 41 2017-05-15 21:43 34 *************** 42 2017-05-15 21:44 34 *************** 43 2017-05-15 21:45 ? - 44 2017-05-15 21:46 34 *************** 45 2017-05-15 21:47 34 *************** 46 2017-05-15 21:48 ? - 47 2017-05-15 21:49 34 *************** 48 2017-05-15 21:50 ? - 49 2017-05-15 21:51 34 *************** 50 2017-05-15 21:52 ? - 51 2017-05-15 21:53 34 *************** ... ..( 3 skipped). .. *************** 55 2017-05-15 21:57 34 *************** 56 2017-05-15 21:58 ? - 57 2017-05-15 21:59 34 *************** 58 2017-05-15 22:00 34 *************** 59 2017-05-15 22:01 ? - 60 2017-05-15 22:02 34 *************** 61 2017-05-15 22:03 ? - 62 2017-05-15 22:04 34 *************** 63 2017-05-15 22:05 34 *************** 64 2017-05-15 22:06 34 *************** 65 2017-05-15 22:07 ? - 66 2017-05-15 22:08 34 *************** ... ..( 7 skipped). .. *************** 74 2017-05-15 22:16 34 *************** 75 2017-05-15 22:17 ? - 76 2017-05-15 22:18 34 *************** 77 2017-05-15 22:19 ? - 78 2017-05-15 22:20 34 *************** 79 2017-05-15 22:21 34 *************** 80 2017-05-15 22:22 34 *************** 81 2017-05-15 22:23 ? - 82 2017-05-15 22:24 34 *************** 83 2017-05-15 22:25 ? - 84 2017-05-15 22:26 35 **************** 85 2017-05-15 22:27 34 *************** 86 2017-05-15 22:28 ? - 87 2017-05-15 22:29 35 **************** 88 2017-05-15 22:30 35 **************** 89 2017-05-15 22:31 35 **************** 90 2017-05-15 22:32 ? - 91 2017-05-15 22:33 35 **************** 92 2017-05-15 22:34 35 **************** 93 2017-05-15 22:35 35 **************** 94 2017-05-15 22:36 ? - 95 2017-05-15 22:37 35 **************** ... ..( 3 skipped). .. **************** 99 2017-05-15 22:41 35 **************** 100 2017-05-15 22:42 ? - 101 2017-05-15 22:43 36 ***************** 102 2017-05-15 22:44 36 ***************** 103 2017-05-15 22:45 ? - 104 2017-05-15 22:46 36 ***************** 105 2017-05-15 22:47 ? - 106 2017-05-15 22:48 36 ***************** 107 2017-05-15 22:49 35 **************** 108 2017-05-15 22:50 ? - 109 2017-05-15 22:51 36 ***************** 110 2017-05-15 22:52 ? - 111 2017-05-15 22:53 26 ******* 112 2017-05-15 22:54 26 ******* 113 2017-05-15 22:55 27 ******** 114 2017-05-15 22:56 ? - 115 2017-05-15 22:57 30 *********** 116 2017-05-15 22:58 30 *********** 117 2017-05-15 22:59 ? - 118 2017-05-15 23:00 30 *********** 119 2017-05-15 23:01 ? - 120 2017-05-15 23:02 30 *********** 121 2017-05-15 23:03 30 *********** 122 2017-05-15 23:04 ? - 123 2017-05-15 23:05 31 ************ 124 2017-05-15 23:06 ? - 125 2017-05-15 23:07 31 ************ ... ..( 3 skipped). .. ************ 1 2017-05-15 23:11 31 ************ 2 2017-05-15 23:12 ? - 3 2017-05-15 23:13 31 ************ SCT Error Recovery Control: Read: 85 (8,5 seconds) Write: 85 (8,5 seconds) Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x8000 4 423 Vendor specific