Probe #ebde292253 of Dell 0TW904 Desktop Computer (OptiPlex 330)

Log: smartctl

/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue Serial ATA Device Model: WDC WD800AAJS-75M0A0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 02.03E02 User Capacity: 80.000.000.000 bytes [80,0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Sun Jul 26 09:38:35 2015 BRT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 40) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 2700) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 36) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 179 3 Spin_Up_Time POS--K 144 134 021 - 3783 4 Start_Stop_Count -O--CK 098 098 000 - 2451 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 094 094 000 - 4827 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2449 192 Power-Off_Retract_Count -O--CK 199 199 000 - 1252 193 Load_Cycle_Count -O--CK 200 200 000 - 2451 194 Temperature_Celsius -O---K 103 093 000 - 40 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 240 Head_Flying_Hours -O--CK 094 094 000 - 4451 241 Total_LBAs_Written -O--CK 200 200 000 - 8107687974 242 Total_LBAs_Read -O--CK 200 200 000 - 3746478622 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 176 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 176 [7] occurred at disk power-on lifetime: 4149 hours (172 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 06 70 00 71 a1 e6 00 Error: UNC 8 sectors at LBA = 0x6760071a1 = 27749544353 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 06 70 00 71 a0 e6 08 00:14:51.672 READ DMA c8 00 00 00 00 00 01 10 00 6f 70 e1 08 00:14:51.666 READ DMA c8 00 00 00 00 00 01 0f 00 6f 70 e1 08 00:14:51.665 READ DMA c8 00 00 00 00 00 01 0e 00 6f 70 e1 08 00:14:51.663 READ DMA c8 00 00 00 00 00 01 0d 00 6f 70 e1 08 00:14:51.662 READ DMA Error 175 [6] occurred at disk power-on lifetime: 4149 hours (172 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 06 70 00 71 a1 e6 00 Error: UNC 8 sectors at LBA = 0x6760071a1 = 27749544353 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 06 70 00 71 a0 e6 08 00:14:49.397 READ DMA c8 00 00 00 00 00 01 08 00 6f 70 e1 08 00:14:49.390 READ DMA c8 00 00 00 00 00 01 07 00 6f 70 e1 08 00:14:49.389 READ DMA c8 00 00 00 00 00 01 06 00 6f 70 e1 08 00:14:49.387 READ DMA c8 00 00 00 00 00 01 05 00 6f 70 e1 08 00:14:49.370 READ DMA Error 174 [5] occurred at disk power-on lifetime: 4149 hours (172 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 06 70 00 71 a1 e6 00 Error: UNC 8 sectors at LBA = 0x6760071a1 = 27749544353 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 06 70 00 71 a0 e6 08 00:14:47.113 READ DMA c8 00 00 00 00 00 01 00 00 6f 70 e1 08 00:14:47.107 READ DMA c8 00 00 00 00 00 01 ff 00 6e 70 e1 08 00:14:47.104 READ DMA c8 00 00 00 00 00 01 fe 00 6e 70 e1 08 00:14:47.103 READ DMA c8 00 00 00 00 00 01 fd 00 6e 70 e1 08 00:14:47.102 READ DMA Error 173 [4] occurred at disk power-on lifetime: 4149 hours (172 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 06 70 00 71 a1 e6 00 Error: UNC 8 sectors at LBA = 0x6760071a1 = 27749544353 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 06 70 00 71 a0 e6 08 00:14:44.706 READ DMA c8 00 00 00 20 00 03 44 00 00 00 e3 08 00:14:44.695 READ DMA c8 00 00 00 00 00 01 f8 00 6e 70 e1 08 00:14:44.688 READ DMA c8 00 00 00 00 00 01 f7 00 6e 70 e1 08 00:14:44.687 READ DMA c8 00 00 00 00 00 01 f6 00 6e 70 e1 08 00:14:44.686 READ DMA Error 172 [3] occurred at disk power-on lifetime: 4149 hours (172 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 06 70 00 71 a1 e6 00 Error: UNC 8 sectors at LBA = 0x6760071a1 = 27749544353 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 06 70 00 71 a0 e6 08 00:14:42.215 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:14:42.215 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:14:42.208 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:14:42.208 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:14:42.208 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 171 [2] occurred at disk power-on lifetime: 4149 hours (172 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 06 70 00 71 a1 e6 00 Error: UNC 8 sectors at LBA = 0x6760071a1 = 27749544353 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 06 70 00 71 a0 e6 08 00:14:39.976 READ DMA c8 00 00 00 00 00 01 e8 00 6e 70 e1 08 00:14:39.971 READ DMA c8 00 00 00 00 00 01 e7 00 6e 70 e1 08 00:14:39.970 READ DMA c8 00 00 00 00 00 01 e6 00 6e 70 e1 08 00:14:39.957 READ DMA c8 00 00 00 00 00 01 e5 00 6e 70 e1 08 00:14:39.956 READ DMA Error 170 [1] occurred at disk power-on lifetime: 4149 hours (172 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 06 70 00 71 a1 e6 00 Error: UNC 8 sectors at LBA = 0x6760071a1 = 27749544353 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 06 70 00 71 a0 e6 08 00:14:37.397 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:14:37.397 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:14:37.390 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:14:37.390 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:14:37.390 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 169 [0] occurred at disk power-on lifetime: 4149 hours (172 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 06 70 00 71 a1 e6 00 Error: UNC 8 sectors at LBA = 0x6760071a1 = 27749544353 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 06 70 00 71 a0 e6 08 00:14:35.118 READ DMA c8 00 00 00 00 00 01 d8 00 6e 70 e1 08 00:14:35.112 READ DMA c8 00 00 00 00 00 01 d7 00 6e 70 e1 08 00:14:35.111 READ DMA c8 00 00 00 00 00 01 d6 00 6e 70 e1 08 00:14:35.109 READ DMA c8 00 00 00 00 00 01 d5 00 6e 70 e1 08 00:14:35.107 READ DMA SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Interrupted (host reset) 80% 2565 - # 2 Short offline Interrupted (host reset) 10% 2562 - # 3 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 40/40 Celsius Lifetime Min/Max Temperature: 40/50 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (192) Index Estimated Time Temperature Celsius 193 2015-07-26 01:41 43 ************************ ... ..( 34 skipped). .. ************************ 228 2015-07-26 02:16 43 ************************ 229 2015-07-26 02:17 44 ************************* ... ..(103 skipped). .. ************************* 333 2015-07-26 04:01 44 ************************* 334 2015-07-26 04:02 43 ************************ ... ..( 4 skipped). .. ************************ 339 2015-07-26 04:07 43 ************************ 340 2015-07-26 04:08 ? - 341 2015-07-26 04:09 44 ************************* ... ..( 3 skipped). .. ************************* 345 2015-07-26 04:13 44 ************************* 346 2015-07-26 04:14 43 ************************ ... ..( 2 skipped). .. ************************ 349 2015-07-26 04:17 43 ************************ 350 2015-07-26 04:18 44 ************************* 351 2015-07-26 04:19 43 ************************ 352 2015-07-26 04:20 44 ************************* 353 2015-07-26 04:21 ? - 354 2015-07-26 04:22 26 ******* 355 2015-07-26 04:23 27 ******** 356 2015-07-26 04:24 28 ********* 357 2015-07-26 04:25 29 ********** 358 2015-07-26 04:26 29 ********** 359 2015-07-26 04:27 30 *********** 360 2015-07-26 04:28 30 *********** 361 2015-07-26 04:29 ? - 362 2015-07-26 04:30 31 ************ 363 2015-07-26 04:31 32 ************* 364 2015-07-26 04:32 33 ************** 365 2015-07-26 04:33 33 ************** 366 2015-07-26 04:34 33 ************** 367 2015-07-26 04:35 34 *************** 368 2015-07-26 04:36 34 *************** 369 2015-07-26 04:37 35 **************** ... ..( 2 skipped). .. **************** 372 2015-07-26 04:40 35 **************** 373 2015-07-26 04:41 36 ***************** 374 2015-07-26 04:42 36 ***************** 375 2015-07-26 04:43 37 ****************** ... ..( 2 skipped). .. ****************** 378 2015-07-26 04:46 37 ****************** 379 2015-07-26 04:47 38 ******************* ... ..( 5 skipped). .. ******************* 385 2015-07-26 04:53 38 ******************* 386 2015-07-26 04:54 39 ******************** ... ..( 2 skipped). .. ******************** 389 2015-07-26 04:57 39 ******************** 390 2015-07-26 04:58 ? - 391 2015-07-26 04:59 40 ********************* 392 2015-07-26 05:00 40 ********************* 393 2015-07-26 05:01 40 ********************* 394 2015-07-26 05:02 43 ************************ ... ..( 82 skipped). .. ************************ 477 2015-07-26 06:25 43 ************************ 0 2015-07-26 06:26 ? - 1 2015-07-26 06:27 43 ************************ 2 2015-07-26 06:28 43 ************************ 3 2015-07-26 06:29 43 ************************ 4 2015-07-26 06:30 44 ************************* 5 2015-07-26 06:31 43 ************************ ... ..( 4 skipped). .. ************************ 10 2015-07-26 06:36 43 ************************ 11 2015-07-26 06:37 44 ************************* 12 2015-07-26 06:38 44 ************************* 13 2015-07-26 06:39 43 ************************ 14 2015-07-26 06:40 44 ************************* ... ..( 3 skipped). .. ************************* 18 2015-07-26 06:44 44 ************************* 19 2015-07-26 06:45 43 ************************ ... ..( 4 skipped). .. ************************ 24 2015-07-26 06:50 43 ************************ 25 2015-07-26 06:51 ? - 26 2015-07-26 06:52 44 ************************* 27 2015-07-26 06:53 43 ************************ 28 2015-07-26 06:54 44 ************************* ... ..( 7 skipped). .. ************************* 36 2015-07-26 07:02 44 ************************* 37 2015-07-26 07:03 43 ************************ 38 2015-07-26 07:04 44 ************************* ... ..( 4 skipped). .. ************************* 43 2015-07-26 07:09 44 ************************* 44 2015-07-26 07:10 43 ************************ 45 2015-07-26 07:11 44 ************************* ... ..( 5 skipped). .. ************************* 51 2015-07-26 07:17 44 ************************* 52 2015-07-26 07:18 45 ************************** 53 2015-07-26 07:19 44 ************************* 54 2015-07-26 07:20 45 ************************** 55 2015-07-26 07:21 44 ************************* 56 2015-07-26 07:22 45 ************************** 57 2015-07-26 07:23 45 ************************** 58 2015-07-26 07:24 44 ************************* ... ..( 53 skipped). .. ************************* 112 2015-07-26 08:18 44 ************************* 113 2015-07-26 08:19 43 ************************ ... ..( 78 skipped). .. ************************ 192 2015-07-26 09:38 43 ************************ SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x8000 4 170 Vendor specific


Hardware for Linux and BSD

GitHub