/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.1-desktop-1omv2290] (OpenMandriva Lx 7.3-2) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F3 Device Model: SAMSUNG HD502HJ Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 1AJ10001 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Mar 3 12:10:58 2023 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 254 APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4800) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 80) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 28990 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 082 070 025 - 5458 4 Start_Stop_Count -O--CK 088 088 000 - 12488 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 35757 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 252 252 000 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3370 191 G-Sense_Error_Rate -O---K 252 252 000 - 0 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 060 000 - 29 (Min/Max 14/40) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 14 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 16 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 11 223 Load_Retry_Count -O--CK 252 252 000 - 0 225 Load_Cycle_Count -O--CK 099 099 000 - 12915 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 20284 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 20284 [3] occurred at disk power-on lifetime: 35659 hours (1485 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 00 03 28 04 40 00 Error: UNC at LBA = 0x00032804 = 206852 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 04 00 00 00 03 28 04 40 08 00:00:01.596 READ FPDMA QUEUED 60 00 03 00 04 00 00 00 03 28 04 40 08 00:00:01.719 READ FPDMA QUEUED 60 00 10 00 08 00 00 33 07 ec 00 40 08 00:00:01.719 READ FPDMA QUEUED 60 00 00 00 08 00 00 36 72 f2 00 40 08 00:00:01.719 READ FPDMA QUEUED 60 00 00 00 08 00 00 13 41 f8 00 40 08 00:00:01.719 READ FPDMA QUEUED Error 20283 [2] occurred at disk power-on lifetime: 35659 hours (1485 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 00 03 28 02 40 00 Error: UNC at LBA = 0x00032802 = 206850 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 03 00 02 00 00 00 03 28 02 40 08 00:00:01.702 READ FPDMA QUEUED 60 00 10 00 02 00 00 00 03 28 02 40 08 00:00:01.718 READ FPDMA QUEUED 60 00 00 00 08 00 00 36 72 f2 00 40 08 00:00:01.718 READ FPDMA QUEUED 60 00 00 00 08 00 00 13 41 f8 00 40 08 00:00:01.718 READ FPDMA QUEUED 60 00 00 00 02 00 00 00 03 28 00 40 08 00:00:01.718 READ FPDMA QUEUED Error 20282 [1] occurred at disk power-on lifetime: 35659 hours (1485 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 00 03 28 04 40 00 Error: UNC at LBA = 0x00032804 = 206852 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 03 00 08 00 00 00 03 28 00 40 08 00:00:01.697 READ FPDMA QUEUED 60 00 10 00 08 00 00 36 72 f1 00 40 08 00:00:01.715 READ FPDMA QUEUED 60 00 00 00 08 00 00 33 07 e9 00 40 08 00:00:01.715 READ FPDMA QUEUED 60 00 00 00 08 00 00 32 8a e0 80 40 08 00:00:01.715 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 03 28 00 40 08 00:00:01.715 READ FPDMA QUEUED Error 20281 [0] occurred at disk power-on lifetime: 35659 hours (1485 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 00 03 27 84 40 00 Error: UNC at LBA = 0x00032784 = 206724 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 03 27 80 40 08 00:00:01.695 READ FPDMA QUEUED 60 00 10 00 08 00 00 00 03 27 80 40 08 00:00:01.711 READ FPDMA QUEUED 60 00 10 00 08 00 00 33 07 e8 40 40 08 00:00:01.711 READ FPDMA QUEUED 60 00 10 00 08 00 00 36 72 f0 40 40 08 00:00:01.711 READ FPDMA QUEUED 60 00 10 00 08 00 00 32 8a e0 20 40 08 00:00:01.711 READ FPDMA QUEUED Error 20280 [7] occurred at disk power-on lifetime: 35659 hours (1485 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 00 03 27 84 40 00 Error: UNC at LBA = 0x00032784 = 206724 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 08 00 00 00 03 27 80 40 08 00:00:01.598 READ FPDMA QUEUED 60 00 10 00 08 00 00 32 8a e0 20 40 08 00:00:01.707 READ FPDMA QUEUED 60 00 00 00 08 00 00 36 72 f0 40 40 08 00:00:01.707 READ FPDMA QUEUED 60 00 10 00 08 00 00 33 07 e8 40 40 08 00:00:01.707 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 03 27 80 40 08 00:00:01.707 READ FPDMA QUEUED Error 20279 [6] occurred at disk power-on lifetime: 35659 hours (1485 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 00 03 28 06 40 00 Error: UNC at LBA = 0x00032806 = 206854 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 02 00 00 00 03 28 06 40 08 00:00:01.598 READ FPDMA QUEUED 60 00 10 00 02 00 00 00 03 28 06 40 08 00:00:01.706 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:01.706 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:01.706 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:01.706 IDENTIFY DEVICE Error 20278 [5] occurred at disk power-on lifetime: 35659 hours (1485 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 00 03 28 04 40 00 Error: UNC at LBA = 0x00032804 = 206852 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 02 00 00 00 03 28 04 40 08 00:00:01.597 READ FPDMA QUEUED 60 00 10 00 02 00 00 00 03 28 06 40 08 00:00:01.704 READ FPDMA QUEUED 60 00 10 00 02 00 00 00 03 28 04 40 08 00:00:01.704 READ FPDMA QUEUED 60 00 10 00 02 00 00 00 03 28 02 40 08 00:00:01.704 READ FPDMA QUEUED 60 00 10 00 08 00 00 32 8a e0 00 40 08 00:00:01.704 READ FPDMA QUEUED Error 20277 [4] occurred at disk power-on lifetime: 35659 hours (1485 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 00 03 28 04 40 00 Error: WP at LBA = 0x00032804 = 206852 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 08 00 00 13 b9 28 00 40 08 00:00:01.704 WRITE FPDMA QUEUED 60 00 00 00 08 00 00 00 03 28 00 40 08 00:00:01.596 READ FPDMA QUEUED 60 00 03 00 08 00 00 33 07 e8 00 40 08 00:00:01.702 READ FPDMA QUEUED 60 00 10 00 08 00 00 32 8a e0 00 40 08 00:00:01.702 READ FPDMA QUEUED 60 00 00 00 08 00 00 36 72 f0 00 40 08 00:00:01.702 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 26/29 Celsius Lifetime Min/Max Temperature: 18/63 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (84) Index Estimated Time Temperature Celsius 85 2023-03-03 01:35 28 ********* ... ..( 49 skipped). .. ********* 7 2023-03-03 05:45 28 ********* 8 2023-03-03 05:50 26 ******* 9 2023-03-03 05:55 27 ******** ... ..( 2 skipped). .. ******** 12 2023-03-03 06:10 27 ******** 13 2023-03-03 06:15 28 ********* 14 2023-03-03 06:20 27 ******** 15 2023-03-03 06:25 28 ********* ... ..( 8 skipped). .. ********* 24 2023-03-03 07:10 28 ********* 25 2023-03-03 07:15 27 ******** 26 2023-03-03 07:20 28 ********* 27 2023-03-03 07:25 27 ******** 28 2023-03-03 07:30 27 ******** 29 2023-03-03 07:35 28 ********* 30 2023-03-03 07:40 27 ******** ... ..( 5 skipped). .. ******** 36 2023-03-03 08:10 27 ******** 37 2023-03-03 08:15 28 ********* 38 2023-03-03 08:20 28 ********* 39 2023-03-03 08:25 27 ******** 40 2023-03-03 08:30 28 ********* 41 2023-03-03 08:35 28 ********* 42 2023-03-03 08:40 27 ******** 43 2023-03-03 08:45 27 ******** 44 2023-03-03 08:50 28 ********* ... ..( 27 skipped). .. ********* 72 2023-03-03 11:10 28 ********* 73 2023-03-03 11:15 29 ********** 74 2023-03-03 11:20 28 ********* 75 2023-03-03 11:25 28 ********* 76 2023-03-03 11:30 29 ********** ... ..( 7 skipped). .. ********** 84 2023-03-03 12:10 29 ********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 5 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific