/dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.11.0-26-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: APPLE HDD HTS541010A9E662 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: JA0AB5D0 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: Not in smartctl database 7.3/5528 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue May 27 15:11:19 2025 AEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 229) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 100 100 040 - 0 3 Spin_Up_Time POS--- 236 236 033 - 1 4 Start_Stop_Count -O--C- 099 099 000 - 1793 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 100 100 040 - 0 9 Power_On_Hours -O--C- 074 074 000 - 11460 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1793 160 Unknown_Attribute -O--CK 100 100 000 - 0 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 4294967363 193 Load_Cycle_Count -O--C- 100 100 000 - 5322 194 Temperature_Celsius -O---- 214 214 000 - 28 (Min/Max 12/48) 195 Hardware_ECC_Recovered -O-R-- 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 254 Free_Fall_Sensor -O--CK 100 100 000 - 3 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 24 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 24 [3] occurred at disk power-on lifetime: 11459 hours (477 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 3a 40 3b 30 0a 00 Error: UNC at LBA = 0x3a403b30 = 977287984 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 58 00 00 3a 40 3b 30 40 00 00:11:55.011 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:11:55.011 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:11:55.010 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:11:55.010 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:11:55.009 SET FEATURES [Set transfer mode] Error 23 [2] occurred at disk power-on lifetime: 11459 hours (477 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 3a 40 3b 30 0a 00 Error: WP at LBA = 0x3a403b30 = 977287984 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 38 00 00 3a 25 a0 00 40 00 00:11:52.563 WRITE FPDMA QUEUED 60 00 08 00 78 00 00 3a 40 3b 30 40 00 00:11:51.191 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:11:51.191 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:11:51.191 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:11:51.190 IDENTIFY DEVICE Error 22 [1] occurred at disk power-on lifetime: 11459 hours (477 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 3a 40 3b 30 0a 00 Error: UNC at LBA = 0x3a403b30 = 977287984 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 10 00 00 3a 40 3b 30 40 00 00:11:47.397 READ FPDMA QUEUED 60 00 20 00 08 00 00 3a 40 3a 98 40 00 00:11:47.397 READ FPDMA QUEUED 60 00 08 00 00 00 00 3a 40 3a 90 40 00 00:11:47.397 READ FPDMA QUEUED 60 00 20 00 f8 00 00 3a 40 39 f8 40 00 00:11:47.397 READ FPDMA QUEUED 60 00 08 00 60 00 00 3a 40 39 f0 40 00 00:11:47.396 READ FPDMA QUEUED Error 21 [0] occurred at disk power-on lifetime: 11459 hours (477 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 3a 40 3b 30 0a 00 Error: UNC at LBA = 0x3a403b30 = 977287984 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 f0 00 00 3a 40 3b 30 40 00 00:11:16.087 READ FPDMA QUEUED 60 01 00 00 e8 00 00 3a 40 39 f0 40 00 00:11:16.084 READ FPDMA QUEUED 60 01 00 00 e0 00 00 3a 40 38 c0 40 00 00:11:16.083 READ FPDMA QUEUED 60 01 00 00 d8 00 00 3a 40 37 a8 40 00 00:11:16.081 READ FPDMA QUEUED 60 01 00 00 00 00 00 3a 40 35 e8 40 00 00:11:16.079 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 28 Celsius Power Cycle Min/Max Temperature: 15/28 Celsius Lifetime Min/Max Temperature: 12/48 Celsius Specified Max Operating Temperature: 27 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (46) Index Estimated Time Temperature Celsius 47 2025-05-27 13:04 37 ****************** 48 2025-05-27 13:05 ? - 49 2025-05-27 13:06 36 ***************** 50 2025-05-27 13:07 37 ****************** 51 2025-05-27 13:08 37 ****************** 52 2025-05-27 13:09 37 ****************** 53 2025-05-27 13:10 38 ******************* 54 2025-05-27 13:11 37 ****************** 55 2025-05-27 13:12 37 ****************** 56 2025-05-27 13:13 37 ****************** 57 2025-05-27 13:14 36 ***************** 58 2025-05-27 13:15 36 ***************** 59 2025-05-27 13:16 35 **************** 60 2025-05-27 13:17 ? - 61 2025-05-27 13:18 35 **************** 62 2025-05-27 13:19 36 ***************** 63 2025-05-27 13:20 36 ***************** 64 2025-05-27 13:21 37 ****************** 65 2025-05-27 13:22 37 ****************** 66 2025-05-27 13:23 37 ****************** 67 2025-05-27 13:24 36 ***************** 68 2025-05-27 13:25 36 ***************** 69 2025-05-27 13:26 36 ***************** 70 2025-05-27 13:27 ? - 71 2025-05-27 13:28 36 ***************** 72 2025-05-27 13:29 37 ****************** ... ..( 2 skipped). .. ****************** 75 2025-05-27 13:32 37 ****************** 76 2025-05-27 13:33 ? - 77 2025-05-27 13:34 37 ****************** 78 2025-05-27 13:35 38 ******************* ... ..( 2 skipped). .. ******************* 81 2025-05-27 13:38 38 ******************* 82 2025-05-27 13:39 ? - 83 2025-05-27 13:40 37 ****************** 84 2025-05-27 13:41 ? - 85 2025-05-27 13:42 38 ******************* 86 2025-05-27 13:43 ? - 87 2025-05-27 13:44 ? - 88 2025-05-27 13:45 35 **************** 89 2025-05-27 13:46 ? - 90 2025-05-27 13:47 34 *************** 91 2025-05-27 13:48 ? - 92 2025-05-27 13:49 31 ************ 93 2025-05-27 13:50 31 ************ 94 2025-05-27 13:51 ? - 95 2025-05-27 13:52 ? - 96 2025-05-27 13:53 31 ************ 97 2025-05-27 13:54 ? - 98 2025-05-27 13:55 31 ************ ... ..( 4 skipped). .. ************ 103 2025-05-27 14:00 31 ************ 104 2025-05-27 14:01 32 ************* ... ..( 4 skipped). .. ************* 109 2025-05-27 14:06 32 ************* 110 2025-05-27 14:07 33 ************** ... ..( 6 skipped). .. ************** 117 2025-05-27 14:14 33 ************** 118 2025-05-27 14:15 34 *************** 119 2025-05-27 14:16 35 **************** 120 2025-05-27 14:17 35 **************** 121 2025-05-27 14:18 36 ***************** ... ..( 15 skipped). .. ***************** 9 2025-05-27 14:34 36 ***************** 10 2025-05-27 14:35 37 ****************** ... ..( 5 skipped). .. ****************** 16 2025-05-27 14:41 37 ****************** 17 2025-05-27 14:42 36 ***************** 18 2025-05-27 14:43 36 ***************** 19 2025-05-27 14:44 36 ***************** 20 2025-05-27 14:45 35 **************** 21 2025-05-27 14:46 ? - 22 2025-05-27 14:47 16 - 23 2025-05-27 14:48 18 - 24 2025-05-27 14:49 19 - 25 2025-05-27 14:50 20 * 26 2025-05-27 14:51 21 ** 27 2025-05-27 14:52 22 *** 28 2025-05-27 14:53 22 *** 29 2025-05-27 14:54 23 **** ... ..( 3 skipped). .. **** 33 2025-05-27 14:58 23 **** 34 2025-05-27 14:59 24 ***** 35 2025-05-27 15:00 24 ***** 36 2025-05-27 15:01 24 ***** 37 2025-05-27 15:02 25 ****** ... ..( 2 skipped). .. ****** 40 2025-05-27 15:05 25 ****** 41 2025-05-27 15:06 26 ******* 42 2025-05-27 15:07 26 ******* 43 2025-05-27 15:08 27 ******** 44 2025-05-27 15:09 27 ******** 45 2025-05-27 15:10 27 ******** 46 2025-05-27 15:11 28 ********* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 56641 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS