/dev/sda === START OF INFORMATION SECTION === Model Family: Seagate Samsung SpinPoint M8 (AF) Device Model: ST500LM012 HN-M500MBB Serial Number: -- LU WWN Device Id: 5 0004cf ... Firmware Version: 2AR10002 User Capacity: 500 107 862 016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Fri May 20 12:43:04 2016 YEKT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 254 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6240) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 104) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 55 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 091 091 025 - 2866 4 Start_Stop_Count -O--CK 099 099 000 - 1043 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 23287 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 545 12 Power_Cycle_Count -O--CK 099 099 000 - 1043 191 G-Sense_Error_Rate -O---K 100 100 000 - 146 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 051 038 000 - 49 (Min/Max 7/62) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 9 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 22558 223 Load_Retry_Count -O--CK 100 100 000 - 545 225 Load_Cycle_Count -O--CK 079 079 000 - 213739 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xc0-0xdf GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 9 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 9 [0] occurred at disk power-on lifetime: 22723 hours (946 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 20 00 00 00 27 43 ca 40 00 Error: ICRC, ABRT at LBA = 0x002743ca = 2573258 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 20 00 00 00 27 43 ea 40 00 00:00:00.353 READ FPDMA QUEUED 60 00 00 00 08 00 00 36 a3 f9 40 40 00 00:00:00.354 READ FPDMA QUEUED 60 00 00 00 03 00 00 00 1e cc 88 40 00 00:00:00.354 READ FPDMA QUEUED 60 00 00 00 c8 00 00 00 27 45 48 40 00 00:00:00.354 READ FPDMA QUEUED 60 00 00 00 d1 00 00 00 36 7c 00 40 00 00:00:00.354 READ FPDMA QUEUED Error 8 [7] occurred at disk power-on lifetime: 15957 hours (664 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 30 00 00 00 2e 65 12 40 00 Error: ICRC, ABRT at LBA = 0x002e6512 = 3040530 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 30 00 00 00 2e 65 22 40 00 00:00:11.559 READ FPDMA QUEUED 60 00 00 00 40 00 00 00 34 6b 82 40 00 00:00:11.561 READ FPDMA QUEUED 60 00 00 00 30 00 00 00 22 31 6a 40 00 00:00:11.561 READ FPDMA QUEUED 60 00 00 00 20 00 00 00 43 be 12 40 00 00:00:11.561 READ FPDMA QUEUED 60 00 00 00 40 00 00 00 2e 65 12 40 00 00:00:11.561 READ FPDMA QUEUED Error 7 [6] occurred at disk power-on lifetime: 10518 hours (438 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 01 38 00 00 0b 09 dc c0 40 00 Error: ICRC, ABRT at LBA = 0x0b09dcc0 = 185195712 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 0b 09 dc f8 40 00 00:00:00.017 READ FPDMA QUEUED 60 00 00 01 00 00 00 0b 09 dc f8 40 00 00:00:00.018 READ FPDMA QUEUED 60 00 00 01 00 00 00 0b 09 db f8 40 00 00:00:00.018 READ FPDMA QUEUED 60 00 00 01 00 00 00 0b 09 da f8 40 00 00:00:00.018 READ FPDMA QUEUED 60 00 00 01 00 00 00 0b 09 d9 f8 40 00 00:00:00.018 READ FPDMA QUEUED Error 6 [5] occurred at disk power-on lifetime: 10038 hours (418 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 ff a8 00 00 38 61 9b 80 40 00 Error: ICRC, ABRT at LBA = 0x38619b80 = 945920896 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 10 00 00 38 61 9b 98 40 08 00:00:00.012 READ FPDMA QUEUED 60 00 00 02 00 00 00 28 90 11 08 40 08 00:00:00.013 READ FPDMA QUEUED 60 00 00 00 f8 00 00 28 90 0f 08 40 08 00:00:00.013 READ FPDMA QUEUED 60 00 00 01 00 00 00 28 90 0e 08 40 08 00:00:00.013 READ FPDMA QUEUED 60 00 00 01 00 00 00 28 90 0d 08 40 08 00:00:00.013 READ FPDMA QUEUED Error 5 [4] occurred at disk power-on lifetime: 9388 hours (391 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 28 00 00 00 5c a8 80 40 00 Error: ICRC, ABRT at LBA = 0x005ca880 = 6072448 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 00 00 5c a8 a8 40 00 00:00:00.044 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 5c a8 e8 40 00 00:00:00.045 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 5c a8 68 40 00 00:00:00.045 READ FPDMA QUEUED 60 00 00 00 10 00 00 00 2d 07 88 40 00 00:00:00.045 READ FPDMA QUEUED 60 00 00 00 28 00 00 02 bd 46 58 40 00 00:00:00.045 READ FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 8890 hours (370 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 80 00 00 00 1d 35 08 40 00 Error: ICRC, ABRT at LBA = 0x001d3508 = 1914120 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 80 00 00 00 1d 35 28 40 00 00:00:00.135 READ FPDMA QUEUED 60 00 00 00 08 00 00 0b a5 68 e0 40 00 00:00:00.136 READ FPDMA QUEUED 60 00 00 00 08 00 00 0b b0 68 78 40 00 00:00:00.136 READ FPDMA QUEUED 60 00 00 00 a0 00 00 00 1d 35 08 40 00 00:00:00.136 READ FPDMA QUEUED 60 00 00 00 08 00 00 0b b1 5f b8 40 00 00:00:00.136 READ FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 6733 hours (280 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 f0 00 00 00 ec de 60 40 00 Error: ICRC, ABRT at LBA = 0x00ecde60 = 15523424 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 f0 00 00 00 ec de 70 40 00 00:00:00.178 READ FPDMA QUEUED 60 00 00 01 00 00 00 00 ec de 60 40 00 00:00:00.179 READ FPDMA QUEUED 60 00 00 00 18 00 00 00 87 e1 62 40 00 00:00:00.179 READ FPDMA QUEUED 60 00 00 01 00 00 00 00 ec dd 60 40 00 00:00:00.179 READ FPDMA QUEUED 60 00 00 00 40 00 00 05 a3 9e 4a 40 00 00:00:00.179 READ FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 806 hours (33 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 30 00 00 0b c5 99 08 40 00 Error: ICRC, ABRT at LBA = 0x0bc59908 = 197499144 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 30 00 00 0b c5 99 18 40 00 00:02:40.587 READ FPDMA QUEUED 60 00 00 00 40 00 00 00 31 57 68 40 00 00:02:40.588 READ FPDMA QUEUED 60 00 00 00 08 00 00 08 70 df 38 40 00 00:02:40.588 READ FPDMA QUEUED 60 00 00 00 40 00 00 00 8b 17 b2 40 00 00:02:40.588 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 7e e5 80 40 00 00:02:40.588 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 49 Celsius Power Cycle Min/Max Temperature: 25/63 Celsius Lifetime Min/Max Temperature: 7/63 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (74) Index Estimated Time Temperature Celsius 75 2016-05-20 02:05 49 ****************************** 76 2016-05-20 02:10 47 **************************** ... ..( 67 skipped). .. **************************** 16 2016-05-20 07:50 47 **************************** 17 2016-05-20 07:55 46 *************************** 18 2016-05-20 08:00 47 **************************** 19 2016-05-20 08:05 46 *************************** 20 2016-05-20 08:10 46 *************************** 21 2016-05-20 08:15 47 **************************** 22 2016-05-20 08:20 47 **************************** 23 2016-05-20 08:25 47 **************************** 24 2016-05-20 08:30 46 *************************** 25 2016-05-20 08:35 46 *************************** 26 2016-05-20 08:40 47 **************************** 27 2016-05-20 08:45 47 **************************** 28 2016-05-20 08:50 47 **************************** 29 2016-05-20 08:55 46 *************************** 30 2016-05-20 09:00 47 **************************** 31 2016-05-20 09:05 47 **************************** 32 2016-05-20 09:10 49 ****************************** 33 2016-05-20 09:15 50 ******************************* 34 2016-05-20 09:20 51 ******************************** 35 2016-05-20 09:25 52 ********************************* 36 2016-05-20 09:30 52 ********************************* 37 2016-05-20 09:35 51 ******************************** 38 2016-05-20 09:40 50 ******************************* 39 2016-05-20 09:45 51 ******************************** 40 2016-05-20 09:50 51 ******************************** 41 2016-05-20 09:55 52 ********************************* 42 2016-05-20 10:00 53 ********************************** 43 2016-05-20 10:05 54 *********************************** 44 2016-05-20 10:10 53 ********************************** 45 2016-05-20 10:15 53 ********************************** 46 2016-05-20 10:20 52 ********************************* 47 2016-05-20 10:25 52 ********************************* 48 2016-05-20 10:30 52 ********************************* 49 2016-05-20 10:35 51 ******************************** ... ..( 8 skipped). .. ******************************** 58 2016-05-20 11:20 51 ******************************** 59 2016-05-20 11:25 50 ******************************* ... ..( 2 skipped). .. ******************************* 62 2016-05-20 11:40 50 ******************************* 63 2016-05-20 11:45 49 ****************************** ... ..( 10 skipped). .. ****************************** 74 2016-05-20 12:40 49 ****************************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 33 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 26 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific