/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.13.0-39-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Momentus 7200.4 Device Model: ST9500420AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0006HPM1 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Apr 20 03:27:58 2022 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 108) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 118 079 006 - 168079635 3 Spin_Up_Time -O---- 096 095 000 - 0 4 Start_Stop_Count PO--CK 086 086 000 - 15305 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 3 7 Seek_Error_Rate POSR-- 069 060 030 - 154937971324 9 Power_On_Hours -O--CK 089 089 000 - 10117 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count PO--CK 086 037 020 - 15231 183 Runtime_Bad_Block -O--CK 100 253 000 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 4310 188 Command_Timeout -O--CK 100 099 000 - 4295032858 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 069 033 045 Past 31 (13 78 31 28 0) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 711 192 Power-Off_Retract_Count -O--CK 100 100 000 - 465 193 Load_Cycle_Count -O--CK 075 075 000 - 50059 194 Temperature_Celsius -O---K 031 067 000 - 31 (0 2 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 044 036 000 - 168079635 196 Reallocated_Event_Count PO--CK 100 100 036 - 3 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 254 Free_Fall_Sensor -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 5943 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5943 [2] occurred at disk power-on lifetime: 9890 hours (412 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 12 90 00 11 d9 00 00 Error: UNC at LBA = 0x12900011d9 = 79725335001 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 19 1e 00 6a 10 40 00 00:08:50.521 READ FPDMA QUEUED 60 00 00 00 a0 00 19 1e 00 6a f8 40 00 00:08:50.521 READ FPDMA QUEUED 60 00 00 00 38 00 19 1e 00 6a a0 40 00 00:08:50.520 READ FPDMA QUEUED 60 00 00 00 08 00 19 1e 00 6a 78 40 00 00:08:50.520 READ FPDMA QUEUED 60 00 00 01 00 00 1b 2c 00 ef 40 40 00 00:08:50.519 READ FPDMA QUEUED Error 5942 [1] occurred at disk power-on lifetime: 9890 hours (412 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 12 90 00 11 d9 00 00 Error: UNC at LBA = 0x12900011d9 = 79725335001 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 1b 28 00 ef 90 40 00 00:08:47.636 READ FPDMA QUEUED 60 00 00 00 b0 00 1b 32 00 ef 50 40 00 00:08:47.633 READ FPDMA QUEUED 60 00 00 00 c8 00 1b 3d 00 ef 98 40 00 00:08:47.631 READ FPDMA QUEUED 60 00 00 00 08 00 12 90 00 11 d8 40 00 00:08:47.624 READ FPDMA QUEUED 60 00 00 00 08 00 12 90 00 11 d0 40 00 00:08:47.623 READ FPDMA QUEUED Error 5941 [0] occurred at disk power-on lifetime: 9890 hours (412 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 12 90 00 11 d9 00 00 Error: UNC at LBA = 0x12900011d9 = 79725335001 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 02 00 00 12 6a 00 11 00 40 00 00:08:44.027 READ FPDMA QUEUED 60 00 00 02 00 00 12 68 00 11 00 40 00 00:08:44.026 READ FPDMA QUEUED 60 00 00 04 00 00 12 70 00 06 00 40 00 00:08:43.725 READ FPDMA QUEUED 60 00 00 08 00 00 12 68 00 06 00 40 00 00:08:43.695 READ FPDMA QUEUED 60 00 00 00 08 00 1a 66 00 f8 d8 40 00 00:08:43.679 READ FPDMA QUEUED Error 5940 [19] occurred at disk power-on lifetime: 9355 hours (389 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 14 00 f3 f8 00 00 Error: UNC at LBA = 0x1400f3f8 = 335606776 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 14 00 f3 90 40 00 05:14:11.170 READ FPDMA QUEUED 60 00 00 01 00 00 00 13 00 f3 90 40 00 05:14:11.170 READ FPDMA QUEUED 60 00 00 01 00 00 00 12 00 f3 90 40 00 05:14:11.169 READ FPDMA QUEUED 60 00 00 01 00 00 00 11 00 f3 90 40 00 05:14:11.169 READ FPDMA QUEUED 60 00 00 01 00 00 00 10 00 f3 90 40 00 05:14:11.169 READ FPDMA QUEUED Error 5939 [18] occurred at disk power-on lifetime: 8859 hours (369 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 14 00 f3 f8 00 00 Error: UNC at LBA = 0x1400f3f8 = 335606776 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 32 00 f3 e0 40 00 00:11:38.442 READ FPDMA QUEUED 60 00 00 01 00 00 00 31 00 f3 e0 40 00 00:11:38.442 READ FPDMA QUEUED 60 00 00 01 00 00 00 30 00 f3 e0 40 00 00:11:38.441 READ FPDMA QUEUED 60 00 00 01 00 00 00 2f 00 f3 e0 40 00 00:11:38.441 READ FPDMA QUEUED 60 00 00 01 00 00 00 2e 00 f3 e0 40 00 00:11:38.440 READ FPDMA QUEUED Error 5938 [17] occurred at disk power-on lifetime: 8846 hours (368 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 03 f3 00 2c 10 00 00 Error: WP at LBA = 0x3f3002c10 = 16961776656 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 c6 00 62 48 40 00 00:08:29.069 WRITE FPDMA QUEUED 61 00 00 00 20 00 1e 68 00 55 c0 40 00 00:08:29.069 WRITE FPDMA QUEUED 61 00 00 01 00 00 07 31 00 53 10 40 00 00:08:29.068 WRITE FPDMA QUEUED 61 00 00 01 00 00 07 30 00 53 10 40 00 00:08:29.067 WRITE FPDMA QUEUED 61 00 00 01 00 00 07 2f 00 53 10 40 00 00:08:29.067 WRITE FPDMA QUEUED Error 5937 [16] occurred at disk power-on lifetime: 8846 hours (368 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 03 f3 00 2c 10 00 00 Error: WP at LBA = 0x3f3002c10 = 16961776656 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 58 00 00 c5 00 62 f0 40 00 00:08:26.155 WRITE FPDMA QUEUED 61 00 00 00 60 00 1e 86 00 7f 40 40 00 00:08:26.155 WRITE FPDMA QUEUED 61 00 00 01 00 00 07 29 00 53 10 40 00 00:08:26.154 WRITE FPDMA QUEUED 61 00 00 01 00 00 07 28 00 53 10 40 00 00:08:26.154 WRITE FPDMA QUEUED 61 00 00 01 00 00 07 27 00 53 10 40 00 00:08:26.154 WRITE FPDMA QUEUED Error 5936 [15] occurred at disk power-on lifetime: 8846 hours (368 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 03 f3 00 2c 10 00 00 Error: WP at LBA = 0x3f3002c10 = 16961776656 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 01 00 00 07 02 00 53 f8 40 00 00:08:23.290 WRITE FPDMA QUEUED 61 00 00 01 00 00 07 01 00 53 f8 40 00 00:08:23.290 WRITE FPDMA QUEUED 61 00 00 01 00 00 07 00 00 53 f8 40 00 00:08:23.287 WRITE FPDMA QUEUED 61 00 00 01 00 00 07 ff 00 52 f8 40 00 00:08:23.287 WRITE FPDMA QUEUED 61 00 00 01 00 00 07 fe 00 52 f8 40 00 00:08:23.286 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 28/31 Celsius Lifetime Min/Max Temperature: 2/67 Celsius Under/Over Temperature Limit Count: 0/15 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (102) Index Estimated Time Temperature Celsius 103 2022-04-20 01:20 32 ************* ... ..( 92 skipped). .. ************* 68 2022-04-20 02:53 32 ************* 69 2022-04-20 02:54 33 ************** ... ..( 16 skipped). .. ************** 86 2022-04-20 03:11 33 ************** 87 2022-04-20 03:12 ? - 88 2022-04-20 03:13 28 ********* 89 2022-04-20 03:14 28 ********* 90 2022-04-20 03:15 29 ********** 91 2022-04-20 03:16 29 ********** 92 2022-04-20 03:17 29 ********** 93 2022-04-20 03:18 30 *********** ... ..( 7 skipped). .. *********** 101 2022-04-20 03:26 30 *********** 102 2022-04-20 03:27 31 ************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS