/dev/nvme0n1 === START OF INFORMATION SECTION === Model Number: SAMSUNG MZVLW128HEGR-00000 Serial Number: -- Firmware Version: CXB7401Q PCI Vendor/Subsystem ID: 0x144d IEEE OUI Identifier: 0x002538 Total NVM Capacity: 128,035,676,160 [128 GB] Unallocated NVM Capacity: 0 Controller ID: 2 Number of Namespaces: 1 Namespace 1 Size/Capacity: 128,035,676,160 [128 GB] Namespace 1 Utilization: 39,398,510,592 [39.3 GB] Namespace 1 Formatted LBA Size: 512 Namespace 1 IEEE EUI-64: 002538 ... Local Time is: Sat Mar 30 16:39:30 2019 +07 Firmware Updates (0x16): 3 Slots, no Reset required Optional Admin Commands (0x0017): Security Format Frmw_DL Self_Test Optional NVM Commands (0x001f): Comp Wr_Unc DS_Mngmt Wr_Zero Sav/Sel_Feat Warning Comp. Temp. Threshold: 68 Celsius Critical Comp. Temp. Threshold: 71 Celsius Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 7.60W - - 0 0 0 0 0 0 1 + 6.00W - - 1 1 1 1 0 0 2 + 5.10W - - 2 2 2 2 0 0 3 - 0.0400W - - 3 3 3 3 210 1500 4 - 0.0050W - - 4 4 4 4 2200 6000 Supported LBA Sizes (NSID 0x1) Id Fmt Data Metadt Rel_Perf 0 + 512 0 0 === START OF SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02, NSID 0x1) Critical Warning: 0x00 Temperature: 35 Celsius Available Spare: 100% Available Spare Threshold: 10% Percentage Used: 0% Data Units Read: 1,006,366 [515 GB] Data Units Written: 885,931 [453 GB] Host Read Commands: 10,852,286 Host Write Commands: 10,287,866 Controller Busy Time: 42 Power Cycles: 361 Power On Hours: 26 Unsafe Shutdowns: 101 Media and Data Integrity Errors: 0 Error Information Log Entries: 42 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Temperature Sensor 1: 35 Celsius Temperature Sensor 2: 42 Celsius Error Information (NVMe Log 0x01, max 64 entries) Num ErrCount SQId CmdId Status PELoc LBA NSID VS 0 42 0 0x0018 0x4004 0x02c 0 0 - 1 41 0 0x0017 0x4004 0x02c 0 0 - 2 40 0 0x0018 0x4004 0x02c 0 0 - 3 39 0 0x0017 0x4004 0x02c 0 0 - 4 38 0 0x0018 0x4004 0x02c 0 0 - 5 37 0 0x0017 0x4004 0x02c 0 0 - 6 36 0 0x0018 0x4004 0x02c 0 0 - 7 35 0 0x0017 0x4004 0x02c 0 0 - 8 34 0 0x0018 0x4004 0x02c 0 0 - 9 33 0 0x0017 0x4004 0x02c 0 0 - 10 32 0 0x0018 0x4004 0x02c 0 0 - 11 31 0 0x0017 0x4004 0x02c 0 0 - 12 30 0 0x0018 0x4004 0x02c 0 0 - 13 29 0 0x0017 0x4004 0x02c 0 0 - 14 28 0 0x0018 0x4004 0x02c 0 0 - 15 27 0 0x0017 0x4004 0x02c 0 0 - ... (26 entries not shown) /dev/sda === START OF INFORMATION SECTION === Model Family: HGST Travelstar 7K1000 Device Model: HGST HTS721010A9E630 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: JB0OA3V0 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Mar 30 16:39:30 2019 +07 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 167) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 165 165 040 - 88 3 Spin_Up_Time POS--- 128 128 033 - 2 4 Start_Stop_Count -O--C- 100 100 000 - 354 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 136 136 040 - 35 9 Power_On_Hours -O--C- 099 099 000 - 539 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 354 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 12 193 Load_Cycle_Count -O--C- 093 093 000 - 76436 194 Temperature_Celsius -O---- 166 166 000 - 36 (Min/Max 14/50) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 35/36 Celsius Lifetime Min/Max Temperature: 14/50 Celsius Lifetime Average Temperature: 35 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (61) Index Estimated Time Temperature Celsius 62 2019-03-30 14:32 35 **************** ... ..( 2 skipped). .. **************** 65 2019-03-30 14:35 35 **************** 66 2019-03-30 14:36 36 ***************** ... ..( 3 skipped). .. ***************** 70 2019-03-30 14:40 36 ***************** 71 2019-03-30 14:41 37 ****************** ... ..( 9 skipped). .. ****************** 81 2019-03-30 14:51 37 ****************** 82 2019-03-30 14:52 38 ******************* 83 2019-03-30 14:53 37 ****************** 84 2019-03-30 14:54 38 ******************* ... ..( 8 skipped). .. ******************* 93 2019-03-30 15:03 38 ******************* 94 2019-03-30 15:04 39 ******************** ... ..( 18 skipped). .. ******************** 113 2019-03-30 15:23 39 ******************** 114 2019-03-30 15:24 38 ******************* 115 2019-03-30 15:25 39 ******************** ... ..( 5 skipped). .. ******************** 121 2019-03-30 15:31 39 ******************** 122 2019-03-30 15:32 38 ******************* 123 2019-03-30 15:33 39 ******************** ... ..( 4 skipped). .. ******************** 0 2019-03-30 15:38 39 ******************** 1 2019-03-30 15:39 38 ******************* ... ..( 11 skipped). .. ******************* 13 2019-03-30 15:51 38 ******************* 14 2019-03-30 15:52 ? - 15 2019-03-30 15:53 38 ******************* 16 2019-03-30 15:54 38 ******************* 17 2019-03-30 15:55 39 ******************** 18 2019-03-30 15:56 ? - 19 2019-03-30 15:57 ? - 20 2019-03-30 15:58 38 ******************* ... ..( 5 skipped). .. ******************* 26 2019-03-30 16:04 38 ******************* 27 2019-03-30 16:05 37 ****************** 28 2019-03-30 16:06 38 ******************* ... ..( 9 skipped). .. ******************* 38 2019-03-30 16:16 38 ******************* 39 2019-03-30 16:17 37 ****************** 40 2019-03-30 16:18 38 ******************* 41 2019-03-30 16:19 37 ****************** ... ..( 4 skipped). .. ****************** 46 2019-03-30 16:24 37 ****************** 47 2019-03-30 16:25 ? - 48 2019-03-30 16:26 37 ****************** 49 2019-03-30 16:27 37 ****************** 50 2019-03-30 16:28 ? - 51 2019-03-30 16:29 ? - 52 2019-03-30 16:30 35 **************** 53 2019-03-30 16:31 ? - 54 2019-03-30 16:32 36 ***************** 55 2019-03-30 16:33 36 ***************** 56 2019-03-30 16:34 ? - 57 2019-03-30 16:35 36 ***************** ... ..( 2 skipped). .. ***************** 60 2019-03-30 16:38 36 ***************** 61 2019-03-30 16:39 35 **************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 4 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS