/dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.10.0-desktop-1omv2490] (OpenMandriva Lx 7.4-1) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: HGST Travelstar Z5K1000 Device Model: HGST HTS541010B7E610 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 03.01A03 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: In smartctl database ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Aug 1 07:22:36 2024 BST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 5820) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 178) minutes. SCT capabilities: (0x303d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 32 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 050 - 3 3 Spin_Up_Time POS--K 055 051 021 - 1425 4 Start_Stop_Count -O--CK 100 100 000 - 4869 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-K 100 100 030 - 52848 9 Power_On_Hours -O--CK 100 100 000 - 23859 10 Spin_Retry_Count PO--CK 100 100 050 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 4869 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO-RCK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 3 188 Command_Timeout -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 3 191 G-Sense_Error_Rate -O--CK 001 001 000 - 125873 192 Power-Off_Retract_Count -O--CK 097 097 000 - 2946347565742 193 Load_Cycle_Count -O--CK 094 094 000 - 13398 194 Temperature_Celsius -O---K 034 053 000 - 34 (Min/Max 34/36) 197 Current_Pending_Sector -O--CK 100 100 000 - 1 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 240 Head_Flying_Hours -O--CK 100 100 000 - 1301764 243 Unknown_Attribute -O--CK 100 100 000 - 25010854 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 277 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 74 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 3 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3 [2] occurred at disk power-on lifetime: 14847 hours (618 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0c 3f 2e 10 40 00 Error: UNC at LBA = 0x0c3f2e10 = 205467152 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 30 00 00 0c 3f 2e 10 40 08 06:52:41.524 READ FPDMA QUEUED 60 01 00 00 28 00 00 0c 3f 2f 10 40 08 06:52:41.524 READ FPDMA QUEUED 61 00 08 00 18 00 00 05 0e 37 30 40 08 06:52:41.524 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 06:52:41.524 FLUSH CACHE EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 06:52:41.524 SET FEATURES [Enable SATA feature] Error 2 [1] occurred at disk power-on lifetime: 14847 hours (618 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0c 3f 2e 10 40 00 Error: WP at LBA = 0x0c3f2e10 = 205467152 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 38 00 b0 00 00 05 0e 36 f8 40 08 06:52:38.256 WRITE FPDMA QUEUED 60 00 08 00 a8 00 00 0c 3f 2e 10 40 08 06:52:38.256 READ FPDMA QUEUED 61 00 30 00 20 00 00 05 d6 39 a0 40 08 06:52:38.256 WRITE FPDMA QUEUED 60 01 00 00 18 00 00 0c 3f 2f 10 40 08 06:52:38.256 READ FPDMA QUEUED 61 00 18 00 10 00 00 05 d6 39 d0 40 08 06:52:38.256 WRITE FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 14847 hours (618 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0c 3f 2e 10 40 00 Error: WP at LBA = 0x0c3f2e10 = 205467152 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 18 00 f0 00 00 05 d6 39 d0 40 08 06:52:36.255 WRITE FPDMA QUEUED 60 01 00 00 e8 00 00 0c 3f 2f 10 40 08 06:52:36.246 READ FPDMA QUEUED 61 00 30 00 e0 00 00 05 d6 39 a0 40 08 06:52:36.246 WRITE FPDMA QUEUED 60 01 00 00 d8 00 00 0c 3f 2e 10 40 08 06:52:35.078 READ FPDMA QUEUED 60 01 00 00 d0 00 00 0c 3f 2d 10 40 08 06:52:34.079 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 4 - # 2 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 34/36 Celsius Lifetime Min/Max Temperature: 12/53 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (120) Index Estimated Time Temperature Celsius 121 2024-08-01 05:15 42 *********************** ... ..( 16 skipped). .. *********************** 10 2024-08-01 05:32 42 *********************** 11 2024-08-01 05:33 41 ********************** ... ..( 9 skipped). .. ********************** 21 2024-08-01 05:43 41 ********************** 22 2024-08-01 05:44 ? - 23 2024-08-01 05:45 23 **** 24 2024-08-01 05:46 24 ***** 25 2024-08-01 05:47 25 ****** 26 2024-08-01 05:48 26 ******* 27 2024-08-01 05:49 27 ******** 28 2024-08-01 05:50 27 ******** 29 2024-08-01 05:51 27 ******** 30 2024-08-01 05:52 28 ********* 31 2024-08-01 05:53 28 ********* 32 2024-08-01 05:54 29 ********** ... ..( 3 skipped). .. ********** 36 2024-08-01 05:58 29 ********** 37 2024-08-01 05:59 30 *********** ... ..( 2 skipped). .. *********** 40 2024-08-01 06:02 30 *********** 41 2024-08-01 06:03 31 ************ ... ..( 4 skipped). .. ************ 46 2024-08-01 06:08 31 ************ 47 2024-08-01 06:09 32 ************* ... ..( 3 skipped). .. ************* 51 2024-08-01 06:13 32 ************* 52 2024-08-01 06:14 33 ************** ... ..( 10 skipped). .. ************** 63 2024-08-01 06:25 33 ************** 64 2024-08-01 06:26 34 *************** ... ..( 11 skipped). .. *************** 76 2024-08-01 06:38 34 *************** 77 2024-08-01 06:39 35 **************** ... ..( 15 skipped). .. **************** 93 2024-08-01 06:55 35 **************** 94 2024-08-01 06:56 36 ***************** ... ..( 7 skipped). .. ***************** 102 2024-08-01 07:04 36 ***************** 103 2024-08-01 07:05 37 ****************** ... ..( 2 skipped). .. ****************** 106 2024-08-01 07:08 37 ****************** 107 2024-08-01 07:09 36 ***************** ... ..( 3 skipped). .. ***************** 111 2024-08-01 07:13 36 ***************** 112 2024-08-01 07:14 ? - 113 2024-08-01 07:15 36 ***************** 114 2024-08-01 07:16 36 ***************** 115 2024-08-01 07:17 36 ***************** 116 2024-08-01 07:18 35 **************** 117 2024-08-01 07:19 35 **************** 118 2024-08-01 07:20 35 **************** 119 2024-08-01 07:21 34 *************** 120 2024-08-01 07:22 34 *************** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 463 Vendor specific