/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.7-desktop-1omv4003] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint M7 Device Model: SAMSUNG HM250HI Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 2AC101C4 User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Thu Feb 24 21:22:46 2022 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4020) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 67) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 1322 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 092 090 025 - 2680 4 Start_Stop_Count -O--CK 095 095 000 - 5999 5 Reallocated_Sector_Ct PO--CK 068 068 010 - 470 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 11289 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 093 093 000 - 7746 12 Power_Cycle_Count -O--CK 094 094 000 - 6465 191 G-Sense_Error_Rate -O---K 100 100 000 - 832 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 054 000 - 22 (Min/Max 13/46) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 068 068 000 - 470 197 Current_Pending_Sector -O--CK 046 045 000 - 786 198 Offline_Uncorrectable ----CK 055 055 000 - 666 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 171 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 23714 223 Load_Retry_Count -O--CK 093 093 000 - 7746 225 Load_Cycle_Count -O--CK 001 001 000 - 4631270 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xbb GPL VS 4 Device vendor specific log 0xbc GPL VS 2 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 720 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 720 [7] occurred at disk power-on lifetime: 11273 hours (469 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1d 1c 4d 60 e0 00 Error: UNC 8 sectors at LBA = 0x1d1c4d60 = 488394080 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 1d 1c 4d 60 e0 0a 00:00:00.041 READ DMA EXT 25 00 00 00 08 00 00 1d 1c 55 b8 e0 0a 00:00:00.041 READ DMA EXT 25 00 00 00 08 00 00 1d 1c 55 90 e0 0a 00:00:00.041 READ DMA EXT 25 00 00 00 08 00 00 1d 1c 55 a0 e0 0a 00:00:00.041 READ DMA EXT 25 00 00 00 08 00 00 1d 1c 55 e0 e0 0a 00:00:00.041 READ DMA EXT Error 719 [6] occurred at disk power-on lifetime: 11265 hours (469 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 06 00 00 1d 1c 55 ba e0 00 Error: UNC 6 sectors at LBA = 0x1d1c55ba = 488396218 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 1d 1c 55 b8 e0 0a 00:00:00.043 READ DMA EXT 25 00 00 00 08 00 00 1d 1c 55 90 e0 0a 00:00:00.043 READ DMA EXT 25 00 00 00 08 00 00 1d 1c 55 a0 e0 0a 00:00:00.043 READ DMA EXT 25 00 00 00 08 00 00 1d 1c 55 e0 e0 0a 00:00:00.043 READ DMA EXT 25 00 00 00 08 00 00 1d 1c 56 90 e0 0a 00:00:00.043 READ DMA EXT Error 718 [5] occurred at disk power-on lifetime: 11246 hours (468 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 07 00 00 1d 1c 55 b9 e0 00 Error: UNC 7 sectors at LBA = 0x1d1c55b9 = 488396217 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 1d 1c 55 b8 e0 0a 00:00:55.978 READ DMA EXT 25 00 00 00 08 00 00 1d 1c 55 90 e0 0a 00:00:55.978 READ DMA EXT 25 00 00 00 08 00 00 1d 1c 55 a0 e0 0a 00:00:55.978 READ DMA EXT 25 00 00 00 08 00 00 1d 1c 55 e0 e0 0a 00:00:55.978 READ DMA EXT 25 00 00 00 08 00 00 1d 1c 56 90 e0 0a 00:00:55.978 READ DMA EXT Error 717 [4] occurred at disk power-on lifetime: 11098 hours (462 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1d 1c 55 e0 e0 00 Error: UNC 8 sectors at LBA = 0x1d1c55e0 = 488396256 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 1d 1c 55 e0 e0 0a 00:00:00.090 READ DMA EXT 25 00 00 00 08 00 00 1d 1c 56 90 e0 0a 00:00:00.090 READ DMA EXT 25 00 00 00 08 00 00 1d 1c 56 c8 e0 0a 00:00:00.090 READ DMA EXT 25 00 00 00 08 00 00 1d 1c 57 20 e0 0a 00:00:00.090 READ DMA EXT 25 00 00 00 08 00 00 1d 1c 57 e0 e0 0a 00:00:00.090 READ DMA EXT Error 716 [3] occurred at disk power-on lifetime: 10622 hours (442 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 5c 00 00 1c 23 98 a4 e0 00 Error: UNC 92 sectors at LBA = 0x1c2398a4 = 472094884 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 1c 23 98 00 e0 0a 00:00:04.046 READ DMA EXT c8 00 00 00 38 00 00 00 c0 46 38 e6 0a 00:00:04.046 READ DMA c8 00 00 00 e0 00 00 00 c0 45 58 e6 0a 00:00:04.046 READ DMA c8 00 00 00 88 00 00 00 c0 46 70 e6 0a 00:00:04.046 READ DMA c8 00 00 00 20 00 00 00 c0 45 38 e6 0a 00:00:04.046 READ DMA Error 715 [2] occurred at disk power-on lifetime: 10622 hours (442 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 5c 00 00 1c 23 98 a4 e0 00 Error: UNC 92 sectors at LBA = 0x1c2398a4 = 472094884 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 78 00 00 1c 23 98 88 e0 0a 00:00:04.035 READ DMA EXT c8 00 00 00 20 00 00 00 b7 ce a0 e6 0a 00:00:04.035 READ DMA 25 00 00 02 00 00 00 1c 23 8c 00 e0 0a 00:00:04.035 READ DMA EXT c8 00 00 00 58 00 00 00 2a 8a 08 ea 0a 00:00:04.035 READ DMA 25 00 00 02 00 00 00 06 2a 84 00 e0 0a 00:00:04.035 READ DMA EXT Error 714 [1] occurred at disk power-on lifetime: 10622 hours (442 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 5c 00 00 1c 23 98 a4 e0 00 Error: UNC 92 sectors at LBA = 0x1c2398a4 = 472094884 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 1c 23 98 00 e0 0a 00:00:03.675 READ DMA EXT c8 00 00 00 00 00 00 00 45 10 00 ec 0a 00:00:03.675 READ DMA c8 00 00 00 00 00 00 00 2a 88 00 e6 0a 00:00:03.675 READ DMA c8 00 00 00 00 00 00 00 10 08 00 e0 0a 00:00:03.675 READ DMA c8 00 00 00 00 00 00 00 00 08 00 e0 0a 00:00:03.675 READ DMA Error 713 [0] occurred at disk power-on lifetime: 10622 hours (442 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 5c 00 00 1c 23 98 a4 e0 00 Error: UNC 92 sectors at LBA = 0x1c2398a4 = 472094884 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 78 00 00 1c 23 98 88 e0 0a 00:00:03.626 READ DMA EXT 25 00 00 00 30 00 00 1c 23 98 48 e0 0a 00:00:03.626 READ DMA EXT 25 00 00 00 10 00 00 1c 23 98 28 e0 0a 00:00:03.626 READ DMA EXT 25 00 00 00 08 00 00 1c 23 98 10 e0 0a 00:00:03.626 READ DMA EXT 25 00 00 00 08 00 00 1c 23 98 78 e0 0a 00:00:03.626 READ DMA EXT SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 21 Celsius Power Cycle Min/Max Temperature: 21/22 Celsius Lifetime Min/Max Temperature: 16/46 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (82) Index Estimated Time Temperature Celsius 83 2022-02-24 10:45 23 **** 84 2022-02-24 10:50 22 *** 85 2022-02-24 10:55 22 *** 86 2022-02-24 11:00 22 *** 87 2022-02-24 11:05 23 **** 88 2022-02-24 11:10 22 *** ... ..( 2 skipped). .. *** 91 2022-02-24 11:25 22 *** 92 2022-02-24 11:30 21 ** 93 2022-02-24 11:35 22 *** 94 2022-02-24 11:40 22 *** 95 2022-02-24 11:45 23 **** 96 2022-02-24 11:50 23 **** 97 2022-02-24 11:55 22 *** 98 2022-02-24 12:00 23 **** 99 2022-02-24 12:05 23 **** 100 2022-02-24 12:10 22 *** 101 2022-02-24 12:15 22 *** 102 2022-02-24 12:20 22 *** 103 2022-02-24 12:25 23 **** 104 2022-02-24 12:30 23 **** 105 2022-02-24 12:35 22 *** 106 2022-02-24 12:40 20 * 107 2022-02-24 12:45 20 * 108 2022-02-24 12:50 20 * 109 2022-02-24 12:55 21 ** 110 2022-02-24 13:00 20 * ... ..( 2 skipped). .. * 113 2022-02-24 13:15 20 * 114 2022-02-24 13:20 21 ** 115 2022-02-24 13:25 21 ** 116 2022-02-24 13:30 22 *** 117 2022-02-24 13:35 21 ** ... ..( 22 skipped). .. ** 12 2022-02-24 15:30 21 ** 13 2022-02-24 15:35 22 *** ... ..( 11 skipped). .. *** 25 2022-02-24 16:35 22 *** 26 2022-02-24 16:40 21 ** 27 2022-02-24 16:45 21 ** 28 2022-02-24 16:50 22 *** 29 2022-02-24 16:55 21 ** 30 2022-02-24 17:00 21 ** 31 2022-02-24 17:05 22 *** ... ..( 26 skipped). .. *** 58 2022-02-24 19:20 22 *** 59 2022-02-24 19:25 21 ** 60 2022-02-24 19:30 21 ** 61 2022-02-24 19:35 21 ** 62 2022-02-24 19:40 22 *** 63 2022-02-24 19:45 22 *** 64 2022-02-24 19:50 21 ** 65 2022-02-24 19:55 21 ** 66 2022-02-24 20:00 22 *** ... ..( 6 skipped). .. *** 73 2022-02-24 20:35 22 *** 74 2022-02-24 20:40 21 ** 75 2022-02-24 20:45 22 *** 76 2022-02-24 20:50 21 ** 77 2022-02-24 20:55 22 *** ... ..( 3 skipped). .. *** 81 2022-02-24 21:15 22 *** 82 2022-02-24 21:20 21 ** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.7-desktop-1omv4003] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar P7K500 Device Model: Hitachi HDP725050GLA360 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: GM4OA5CA User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Thu Feb 24 21:22:47 2022 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7890) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 131) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 132 132 054 - 143 3 Spin_Up_Time POS--- 123 123 024 - 316 (Average 307) 4 Start_Stop_Count -O--C- 100 100 000 - 3174 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 100 100 020 - 0 9 Power_On_Hours -O--C- 099 099 000 - 8911 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 2698 192 Power-Off_Retract_Count -O--CK 098 098 000 - 3321 193 Load_Cycle_Count -O--C- 098 098 000 - 3321 194 Temperature_Celsius -O---- 253 253 000 - 23 (Min/Max 13/46) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 1654 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 3165 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 23 Celsius Power Cycle Min/Max Temperature: 23/23 Celsius Lifetime Min/Max Temperature: 13/46 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (114) Index Estimated Time Temperature Celsius 115 2022-02-24 19:15 23 **** ... ..( 2 skipped). .. **** 118 2022-02-24 19:18 23 **** 119 2022-02-24 19:19 24 ***** ... ..( 4 skipped). .. ***** 124 2022-02-24 19:24 24 ***** 125 2022-02-24 19:25 25 ****** 126 2022-02-24 19:26 25 ****** 127 2022-02-24 19:27 24 ***** ... ..( 4 skipped). .. ***** 4 2022-02-24 19:32 24 ***** 5 2022-02-24 19:33 23 **** ... ..( 15 skipped). .. **** 21 2022-02-24 19:49 23 **** 22 2022-02-24 19:50 24 ***** ... ..( 3 skipped). .. ***** 26 2022-02-24 19:54 24 ***** 27 2022-02-24 19:55 23 **** 28 2022-02-24 19:56 23 **** 29 2022-02-24 19:57 23 **** 30 2022-02-24 19:58 24 ***** 31 2022-02-24 19:59 24 ***** 32 2022-02-24 20:00 23 **** 33 2022-02-24 20:01 ? - 34 2022-02-24 20:02 ? - 35 2022-02-24 20:03 23 **** ... ..( 78 skipped). .. **** 114 2022-02-24 21:22 23 **** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS