/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.1-desktop-1omv2290] (OpenMandriva Lx 7.3-2) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Momentus 5400.6 Device Model: ST9500325AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0001SDM1 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Mar 11 07:04:08 2023 -03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 135) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 111 099 006 - 40362107 3 Spin_Up_Time PO---- 099 098 000 - 0 4 Start_Stop_Count -O--CK 097 097 020 - 4034 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 3 7 Seek_Error_Rate POSR-- 086 060 030 - 453521326 9 Power_On_Hours -O--CK 091 091 000 - 7958 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 097 097 020 - 3292 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 098 098 000 - 2 188 Command_Timeout -O--CK 100 001 000 - 3298585218845 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 068 047 045 - 32 (Min/Max 27/32) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 154 192 Power-Off_Retract_Count -O--CK 100 100 000 - 186 193 Load_Cycle_Count -O--CK 083 083 000 - 35971 194 Temperature_Celsius -O---K 032 053 000 - 32 (0 6 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 053 046 000 - 40362107 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 001 000 - 3053 254 Free_Fall_Sensor -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 2 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2 [1] occurred at disk power-on lifetime: 406 hours (16 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 c4 00 3a 03 84 00 00 Error: WP at LBA = 0xc4003a0384 = 841817392004 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 75 00 78 00 68 40 00 03:15:31.185 WRITE FPDMA QUEUED 60 00 00 01 00 00 c4 00 3a 03 28 40 00 03:15:31.184 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 00 00 03:15:31.125 FLUSH CACHE EXT 61 00 00 00 20 00 88 00 4e 1c 40 40 00 03:15:31.113 WRITE FPDMA QUEUED 61 00 00 00 08 00 75 00 78 00 70 40 00 03:15:31.112 WRITE FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 406 hours (16 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 c4 00 3a 03 85 00 00 Error: UNC at LBA = 0xc4003a0385 = 841817392005 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 20 00 c4 00 3a 03 80 40 00 03:15:28.024 READ FPDMA QUEUED 61 00 00 00 20 00 88 00 4e 1c 40 40 00 03:15:28.023 WRITE FPDMA QUEUED 61 00 00 00 20 00 a0 00 6e 03 60 40 00 03:15:28.023 WRITE FPDMA QUEUED 60 00 00 00 20 00 c4 00 3a 03 60 40 00 03:15:28.022 READ FPDMA QUEUED 61 00 00 00 20 00 88 00 4e 1c 40 40 00 03:15:28.022 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 27/31 Celsius Lifetime Min/Max Temperature: 6/53 Celsius Under/Over Temperature Limit Count: 0/7 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (70) Index Estimated Time Temperature Celsius 71 2023-03-11 04:57 38 ******************* ... ..( 26 skipped). .. ******************* 98 2023-03-11 05:24 38 ******************* 99 2023-03-11 05:25 37 ****************** 100 2023-03-11 05:26 37 ****************** 101 2023-03-11 05:27 37 ****************** 102 2023-03-11 05:28 36 ***************** ... ..( 6 skipped). .. ***************** 109 2023-03-11 05:35 36 ***************** 110 2023-03-11 05:36 35 **************** ... ..( 39 skipped). .. **************** 22 2023-03-11 06:16 35 **************** 23 2023-03-11 06:17 ? - 24 2023-03-11 06:18 28 ********* 25 2023-03-11 06:19 ? - 26 2023-03-11 06:20 29 ********** 27 2023-03-11 06:21 30 *********** 28 2023-03-11 06:22 31 ************ 29 2023-03-11 06:23 ? - 30 2023-03-11 06:24 31 ************ 31 2023-03-11 06:25 31 ************ 32 2023-03-11 06:26 32 ************* ... ..( 4 skipped). .. ************* 37 2023-03-11 06:31 32 ************* 38 2023-03-11 06:32 31 ************ 39 2023-03-11 06:33 32 ************* ... ..( 3 skipped). .. ************* 43 2023-03-11 06:37 32 ************* 44 2023-03-11 06:38 29 ********** 45 2023-03-11 06:39 30 *********** 46 2023-03-11 06:40 30 *********** 47 2023-03-11 06:41 31 ************ 48 2023-03-11 06:42 31 ************ 49 2023-03-11 06:43 30 *********** 50 2023-03-11 06:44 31 ************ 51 2023-03-11 06:45 32 ************* 52 2023-03-11 06:46 33 ************** 53 2023-03-11 06:47 33 ************** 54 2023-03-11 06:48 32 ************* 55 2023-03-11 06:49 ? - 56 2023-03-11 06:50 30 *********** 57 2023-03-11 06:51 31 ************ 58 2023-03-11 06:52 32 ************* 59 2023-03-11 06:53 30 *********** 60 2023-03-11 06:54 ? - 61 2023-03-11 06:55 26 ******* 62 2023-03-11 06:56 27 ******** 63 2023-03-11 06:57 ? - 64 2023-03-11 06:58 27 ******** 65 2023-03-11 06:59 28 ********* 66 2023-03-11 07:00 28 ********* 67 2023-03-11 07:01 29 ********** 68 2023-03-11 07:02 29 ********** 69 2023-03-11 07:03 30 *********** 70 2023-03-11 07:04 31 ************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS