/dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.14.1-300.fc42.x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Crucial/Micron Client SSDs Device Model: CT240BX500SSD1 Serial Number: -- LU WWN Device Id: 0 000000 ... Firmware Version: M6CR013 User Capacity: 240,057,409,536 bytes [240 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5528 ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Apr 10 07:29:43 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 050 - 0 5 Reallocate_NAND_Blk_Cnt -O--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 050 - 38890 12 Power_Cycle_Count -O--CK 100 100 050 - 58 171 Program_Fail_Count -O--CK 100 100 050 - 0 172 Erase_Fail_Count -O--CK 100 100 050 - 0 173 Ave_Block-Erase_Count -O--CK 100 100 050 - 342 174 Unexpect_Power_Loss_Ct -O--CK 100 100 050 - 16 180 Unused_Reserve_NAND_Blk -O--CK 100 100 050 - 100 183 SATA_Interfac_Downshift -O--CK 100 100 050 - 0 184 Error_Correction_Count -O--CK 100 100 050 - 0 187 Reported_Uncorrect -O--CK 100 100 050 - 0 194 Temperature_Celsius -O---K 063 030 050 Past 37 (Min/Max 28/70) 196 Reallocated_Event_Count -O--CK 100 100 050 - 0 197 Current_Pending_ECC_Cnt -O--CK 100 100 050 - 0 198 Offline_Uncorrectable ----CK 100 100 050 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 050 - 1 202 Percent_Lifetime_Remain ----CK 078 078 001 - 78 206 Write_Error_Rate -OSR-K 100 100 050 - 0 210 Success_RAIN_Recov_Cnt -O--CK 100 100 050 - 0 246 Total_LBAs_Written -O--CK 100 100 050 - 173697964330 247 Host_Program_Page_Count -O--CK 100 100 050 - 5428061385 248 FTL_Program_Page_Count -O--CK 100 100 050 - 3527313696 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 88 Current Device Internal Status Data log 0x25 GPL R/O 32 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 3 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3 [2] log entry is empty Error 2 [1] log entry is empty Error 1 [0] log entry is empty SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 58 --- Lifetime Power-On Resets 0x01 0x010 4 38890 --- Power-on Hours 0x01 0x018 6 1899272490 --- Logical Sectors Written 0x01 0x020 6 1005799999 --- Number of Write Commands 0x01 0x028 6 3405530858 --- Logical Sectors Read 0x01 0x030 6 137736902 --- Number of Read Commands 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 81 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0005 4 22 R_ERR response for non-data FIS 0x000a 4 110 Device-to-host register FISes sent due to a COMRESET /dev/sdb smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.14.1-300.fc42.x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Maxtor DiamondMax 10 (ATA/133 and SATA/150) Device Model: Maxtor 6B200M0 Serial Number: -- Firmware Version: BANC1B70 User Capacity: 203,927,027,200 bytes [203 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5528 ATA Version is: ATA/ATAPI-7 T13/1532D revision 0 Local Time is: Thu Apr 10 07:29:43 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 192 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 1562) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 81) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 3 Spin_Up_Time POS--K 208 181 063 - 10515 4 Start_Stop_Count -O--CK 253 253 000 - 857 5 Reallocated_Sector_Ct PO--CK 253 253 063 - 0 6 Read_Channel_Margin P----- 253 253 100 - 0 7 Seek_Error_Rate -O-R-- 253 252 000 - 0 8 Seek_Time_Performance POS--K 246 225 187 - 62430 9 Power_On_Minutes -O--CK 001 001 000 - 197h+27m 10 Spin_Retry_Count PO-R-K 253 221 157 - 0 11 Calibration_Retry_Count PO-R-K 253 252 223 - 0 12 Power_Cycle_Count -O--CK 250 250 000 - 1194 192 Power-Off_Retract_Count -O--CK 253 253 000 - 0 193 Load_Cycle_Count -O--CK 253 253 000 - 0 194 Temperature_Celsius -O--CK 028 253 000 - 27 195 Hardware_ECC_Recovered -O-R-- 253 252 000 - 21292 196 Reallocated_Event_Count ---R-- 253 253 000 - 0 197 Current_Pending_Sector ---R-- 253 253 000 - 0 198 Offline_Uncorrectable ---R-- 253 252 000 - 0 199 UDMA_CRC_Error_Count ---R-- 199 199 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 253 252 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 252 000 - 0 202 Data_Address_Mark_Errs -O-R-- 253 221 000 - 0 203 Run_Out_Cancel PO-R-- 253 252 180 - 0 204 Soft_ECC_Correction -O-R-- 253 252 000 - 0 205 Thermal_Asperity_Rate -O-R-- 253 252 000 - 0 207 Spin_High_Current -O-R-K 253 221 000 - 0 208 Spin_Buzz -O-R-K 253 252 000 - 0 209 Offline_Seek_Performnce --S--K 239 239 000 - 169 210 Unknown_Attribute -O--CK 253 252 000 - 0 211 Unknown_Attribute -O--CK 253 252 000 - 0 212 Unknown_Attribute -O--CK 253 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning Read SMART Log Directory failed: scsi error badly formed scsi parameters General Purpose Log Directory Version 1 Address Access R/W Size Description 0x00 GPL R/O 1 Log Directory 0x02 GPL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 4 Ext. Comprehensive SMART error log 0x06 GPL R/O 1 SMART self-test log 0x10 GPL R/O 1 NCQ Command Error log SMART Extended Comprehensive Error Log Version: 1 (4 sectors) Device Error Count: 5406 (device log contains only the most recent 16 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5406 [13] occurred at disk power-on lifetime: 26235 hours (1093 days + 3 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 78 -- 00 00 00 00 00 00 00 00 00 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 60 00 00 00 d4 00 00 00 a0 0a 00:33:53.369 IDENTIFY DEVICE c8 00 00 00 60 00 00 00 da 41 c5 e1 08 00:33:51.954 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:33:51.953 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 46 00 00 00 00 00 00 00 a0 0a 00:33:51.950 IDENTIFY DEVICE ef 00 03 00 46 00 00 ff 00 00 00 a0 0a 00:33:51.947 SET FEATURES [Set transfer mode] Error 5405 [12] occurred at disk power-on lifetime: 26235 hours (1093 days + 3 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 78 -- 00 60 00 da 41 d4 00 00 00 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 60 00 00 00 d4 00 00 00 a0 0a 00:33:51.852 IDENTIFY DEVICE c8 00 00 00 60 00 00 00 da 41 c5 e1 08 00:33:50.455 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:33:50.454 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 46 00 00 00 00 00 00 00 a0 0a 00:33:50.451 IDENTIFY DEVICE ef 00 03 00 46 00 00 ff 00 00 00 a0 0a 00:33:50.448 SET FEATURES [Set transfer mode] Error 5404 [11] occurred at disk power-on lifetime: 26235 hours (1093 days + 3 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 78 -- 00 00 00 00 00 00 00 00 00 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 60 00 00 00 d4 00 00 00 a0 0a 00:33:56.352 IDENTIFY DEVICE c8 00 00 00 60 00 00 00 da 41 c5 e1 08 00:33:54.942 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:33:54.941 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 46 00 00 00 00 00 00 00 a0 0a 00:33:54.938 IDENTIFY DEVICE ef 00 03 00 46 00 00 ff 00 00 00 a0 0a 00:33:54.935 SET FEATURES [Set transfer mode] Error 5403 [10] occurred at disk power-on lifetime: 26235 hours (1093 days + 3 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 78 -- 00 60 00 da 41 d4 00 00 00 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 60 00 00 00 d4 00 00 00 a0 0a 00:33:54.843 IDENTIFY DEVICE c8 00 00 00 60 00 00 00 da 41 c5 e1 08 00:33:53.453 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:33:53.452 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 46 00 00 00 00 00 00 00 a0 0a 00:33:53.449 IDENTIFY DEVICE ef 00 03 00 46 00 00 ff 00 00 00 a0 0a 00:33:53.446 SET FEATURES [Set transfer mode] Error 5402 [9] occurred at disk power-on lifetime: 26235 hours (1093 days + 3 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 78 -- 00 00 00 00 00 00 00 00 00 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 60 00 00 00 d4 00 00 00 a0 0a 00:33:53.369 IDENTIFY DEVICE c8 00 00 00 60 00 00 00 da 41 c5 e1 08 00:33:51.954 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:33:51.953 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 46 00 00 00 00 00 00 00 a0 0a 00:33:51.950 IDENTIFY DEVICE ef 00 03 00 46 00 00 ff 00 00 00 a0 0a 00:33:51.947 SET FEATURES [Set transfer mode] Error 5401 [8] occurred at disk power-on lifetime: 26235 hours (1093 days + 3 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 78 -- 00 60 00 da 41 d4 00 00 00 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 60 00 00 00 d4 00 00 00 a0 0a 00:33:51.852 IDENTIFY DEVICE c8 00 00 00 60 00 00 00 da 41 c5 e1 08 00:33:50.455 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:33:50.454 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 46 00 00 00 00 00 00 00 a0 0a 00:33:50.451 IDENTIFY DEVICE ef 00 03 00 46 00 00 ff 00 00 00 a0 0a 00:33:50.448 SET FEATURES [Set transfer mode] Error 5400 [7] occurred at disk power-on lifetime: 26235 hours (1093 days + 3 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 78 -- 00 00 00 00 00 00 00 00 00 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 60 00 00 00 d4 00 00 00 a0 0a 00:33:56.352 IDENTIFY DEVICE c8 00 00 00 60 00 00 00 da 41 c5 e1 08 00:33:54.942 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:33:54.941 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 46 00 00 00 00 00 00 00 a0 0a 00:33:54.938 IDENTIFY DEVICE ef 00 03 00 46 00 00 ff 00 00 00 a0 0a 00:33:54.935 SET FEATURES [Set transfer mode] Error 5399 [6] occurred at disk power-on lifetime: 26235 hours (1093 days + 3 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 78 -- 00 60 00 da 41 d4 00 00 00 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 60 00 00 00 d4 00 00 00 a0 0a 00:33:54.843 IDENTIFY DEVICE c8 00 00 00 60 00 00 00 da 41 c5 e1 08 00:33:53.453 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:33:53.452 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 46 00 00 00 00 00 00 00 a0 0a 00:33:53.449 IDENTIFY DEVICE ef 00 03 00 46 00 00 ff 00 00 00 a0 0a 00:33:53.446 SET FEATURES [Set transfer mode] SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 20592 - # 2 Extended offline Completed without error 00% 26338 - # 3 Short offline Completed: read failure 60% 26150 339889 1 of 1 failed self-tests are outdated by newer successful extended offline self-test # 1 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) not supported /dev/sdc smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.14.1-300.fc42.x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: TOSHIBA HDWR480 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: 0601 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database 7.3/5528 ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Apr 10 07:29:44 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 674) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--K 100 100 001 - 12207 4 Start_Stop_Count -O--CK 100 100 000 - 4 5 Reallocated_Sector_Ct PO--CK 100 100 050 - 0 7 Seek_Error_Rate PO-R-- 100 100 050 - 0 8 Seek_Time_Performance P-S--- 100 100 050 - 0 9 Power_On_Hours -O--CK 076 076 000 - 9946 10 Spin_Retry_Count PO--CK 100 100 030 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 4 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 0 193 Load_Cycle_Count -O--CK 100 100 000 - 215 194 Temperature_Celsius -O---K 100 100 000 - 25 (Min/Max 18/37) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 220 Disk_Shift -O---- 100 100 000 - 135004210 222 Loaded_Hours -O--CK 098 098 000 - 1159 223 Load_Retry_Count -O--CK 100 100 000 - 0 224 Load_Friction -O---K 100 100 000 - 0 226 Load-in_Time -OS--K 100 100 000 - 503 240 Head_Flying_Hours P----- 100 100 001 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 513 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 53248 Current Device Internal Status Data log 0x25 GPL R/O 53248 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xae GPL VS 25 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 25 Celsius Power Cycle Min/Max Temperature: 18/33 Celsius Lifetime Min/Max Temperature: 18/37 Celsius Specified Max Operating Temperature: 55 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/55 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 478 (251) Index Estimated Time Temperature Celsius 252 2025-04-09 23:32 26 ******* ... ..(199 skipped). .. ******* 452 2025-04-10 02:52 26 ******* 453 2025-04-10 02:53 25 ****** 454 2025-04-10 02:54 26 ******* 455 2025-04-10 02:55 26 ******* 456 2025-04-10 02:56 25 ****** 457 2025-04-10 02:57 26 ******* ... ..( 6 skipped). .. ******* 464 2025-04-10 03:04 26 ******* 465 2025-04-10 03:05 25 ****** 466 2025-04-10 03:06 26 ******* 467 2025-04-10 03:07 25 ****** 468 2025-04-10 03:08 26 ******* 469 2025-04-10 03:09 25 ****** 470 2025-04-10 03:10 26 ******* ... ..( 4 skipped). .. ******* 475 2025-04-10 03:15 26 ******* 476 2025-04-10 03:16 25 ****** 477 2025-04-10 03:17 26 ******* 0 2025-04-10 03:18 26 ******* 1 2025-04-10 03:19 26 ******* 2 2025-04-10 03:20 25 ****** 3 2025-04-10 03:21 26 ******* ... ..( 8 skipped). .. ******* 12 2025-04-10 03:30 26 ******* 13 2025-04-10 03:31 25 ****** 14 2025-04-10 03:32 25 ****** 15 2025-04-10 03:33 26 ******* 16 2025-04-10 03:34 26 ******* 17 2025-04-10 03:35 25 ****** 18 2025-04-10 03:36 26 ******* 19 2025-04-10 03:37 26 ******* 20 2025-04-10 03:38 25 ****** ... ..( 2 skipped). .. ****** 23 2025-04-10 03:41 25 ****** 24 2025-04-10 03:42 26 ******* ... ..( 3 skipped). .. ******* 28 2025-04-10 03:46 26 ******* 29 2025-04-10 03:47 25 ****** 30 2025-04-10 03:48 26 ******* 31 2025-04-10 03:49 25 ****** 32 2025-04-10 03:50 25 ****** 33 2025-04-10 03:51 25 ****** 34 2025-04-10 03:52 26 ******* 35 2025-04-10 03:53 25 ****** 36 2025-04-10 03:54 26 ******* 37 2025-04-10 03:55 25 ****** ... ..( 2 skipped). .. ****** 40 2025-04-10 03:58 25 ****** 41 2025-04-10 03:59 26 ******* ... ..( 2 skipped). .. ******* 44 2025-04-10 04:02 26 ******* 45 2025-04-10 04:03 25 ****** 46 2025-04-10 04:04 25 ****** 47 2025-04-10 04:05 26 ******* 48 2025-04-10 04:06 25 ****** 49 2025-04-10 04:07 26 ******* 50 2025-04-10 04:08 26 ******* 51 2025-04-10 04:09 25 ****** ... ..( 5 skipped). .. ****** 57 2025-04-10 04:15 25 ****** 58 2025-04-10 04:16 26 ******* 59 2025-04-10 04:17 25 ****** ... ..( 9 skipped). .. ****** 69 2025-04-10 04:27 25 ****** 70 2025-04-10 04:28 26 ******* 71 2025-04-10 04:29 25 ****** ... ..(179 skipped). .. ****** 251 2025-04-10 07:29 25 ****** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 3) == 0x01 0x008 4 4 --- Lifetime Power-On Resets 0x01 0x010 4 9946 --- Power-on Hours 0x01 0x018 6 3502942977 --- Logical Sectors Written 0x01 0x020 6 2306059 --- Number of Write Commands 0x01 0x028 6 22219493 --- Logical Sectors Read 0x01 0x030 6 108346 --- Number of Read Commands 0x01 0x038 6 35805600000 --- Date and Time TimeStamp 0x02 ===== = = === == Free-Fall Statistics (rev 1) == 0x02 0x010 4 0 --- Overlimit Shock Events 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 401 --- Spindle Motor Power-on Hours 0x03 0x010 4 1159 --- Head Flying Hours 0x03 0x018 4 215 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 2 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x03 0x040 4 0 --- Number of High Priority Unload Events 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 25 --- Current Temperature 0x05 0x010 1 25 N-- Average Short Term Temperature 0x05 0x018 1 25 N-- Average Long Term Temperature 0x05 0x020 1 37 --- Highest Temperature 0x05 0x028 1 18 --- Lowest Temperature 0x05 0x030 1 33 N-- Highest Average Short Term Temperature 0x05 0x038 1 23 N-- Lowest Average Short Term Temperature 0x05 0x040 1 30 N-- Highest Average Long Term Temperature 0x05 0x048 1 24 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 600 --- Number of Hardware Resets 0x06 0x010 4 350 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 153003 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 107 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdd smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.14.1-300.fc42.x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: TOSHIBA HDWR480 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: 0601 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database 7.3/5528 ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Apr 10 07:29:44 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 671) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--K 100 100 001 - 12366 4 Start_Stop_Count -O--CK 100 100 000 - 25 5 Reallocated_Sector_Ct PO--CK 100 100 050 - 0 7 Seek_Error_Rate PO-R-- 100 100 050 - 0 8 Seek_Time_Performance P-S--- 100 100 050 - 0 9 Power_On_Hours -O--CK 039 039 000 - 24497 10 Spin_Retry_Count PO--CK 100 100 030 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 25 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 7 193 Load_Cycle_Count -O--CK 100 100 000 - 1055 194 Temperature_Celsius -O---K 100 100 000 - 25 (Min/Max 7/38) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 220 Disk_Shift -O---- 100 100 000 - 51249153 222 Loaded_Hours -O--CK 092 092 000 - 3367 223 Load_Retry_Count -O--CK 100 100 000 - 0 224 Load_Friction -O---K 100 100 000 - 0 226 Load-in_Time -OS--K 100 100 000 - 515 240 Head_Flying_Hours P----- 100 100 001 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 513 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 53248 Current Device Internal Status Data log 0x25 GPL R/O 53248 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xae GPL VS 25 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 25 Celsius Power Cycle Min/Max Temperature: 18/33 Celsius Lifetime Min/Max Temperature: 7/38 Celsius Specified Max Operating Temperature: 55 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/55 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 478 (81) Index Estimated Time Temperature Celsius 82 2025-04-09 23:32 29 ********** ... ..( 60 skipped). .. ********** 143 2025-04-10 00:33 29 ********** 144 2025-04-10 00:34 28 ********* ... ..( 2 skipped). .. ********* 147 2025-04-10 00:37 28 ********* 148 2025-04-10 00:38 27 ******** ... ..( 7 skipped). .. ******** 156 2025-04-10 00:46 27 ******** 157 2025-04-10 00:47 26 ******* ... ..(227 skipped). .. ******* 385 2025-04-10 04:35 26 ******* 386 2025-04-10 04:36 25 ****** 387 2025-04-10 04:37 25 ****** 388 2025-04-10 04:38 26 ******* 389 2025-04-10 04:39 26 ******* 390 2025-04-10 04:40 25 ****** 391 2025-04-10 04:41 26 ******* 392 2025-04-10 04:42 25 ****** 393 2025-04-10 04:43 26 ******* 394 2025-04-10 04:44 26 ******* 395 2025-04-10 04:45 25 ****** 396 2025-04-10 04:46 25 ****** 397 2025-04-10 04:47 25 ****** 398 2025-04-10 04:48 26 ******* ... ..( 2 skipped). .. ******* 401 2025-04-10 04:51 26 ******* 402 2025-04-10 04:52 25 ****** 403 2025-04-10 04:53 26 ******* 404 2025-04-10 04:54 25 ****** 405 2025-04-10 04:55 26 ******* 406 2025-04-10 04:56 25 ****** 407 2025-04-10 04:57 25 ****** 408 2025-04-10 04:58 26 ******* 409 2025-04-10 04:59 26 ******* 410 2025-04-10 05:00 25 ****** ... ..( 2 skipped). .. ****** 413 2025-04-10 05:03 25 ****** 414 2025-04-10 05:04 26 ******* 415 2025-04-10 05:05 25 ****** 416 2025-04-10 05:06 25 ****** 417 2025-04-10 05:07 26 ******* 418 2025-04-10 05:08 25 ****** 419 2025-04-10 05:09 25 ****** 420 2025-04-10 05:10 26 ******* 421 2025-04-10 05:11 25 ****** ... ..( 2 skipped). .. ****** 424 2025-04-10 05:14 25 ****** 425 2025-04-10 05:15 26 ******* 426 2025-04-10 05:16 25 ****** 427 2025-04-10 05:17 25 ****** 428 2025-04-10 05:18 25 ****** 429 2025-04-10 05:19 26 ******* 430 2025-04-10 05:20 25 ****** ... ..( 2 skipped). .. ****** 433 2025-04-10 05:23 25 ****** 434 2025-04-10 05:24 26 ******* 435 2025-04-10 05:25 26 ******* 436 2025-04-10 05:26 25 ****** ... ..(122 skipped). .. ****** 81 2025-04-10 07:29 25 ****** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 3) == 0x01 0x008 4 25 --- Lifetime Power-On Resets 0x01 0x010 4 24497 --- Power-on Hours 0x01 0x018 6 2723735432 --- Logical Sectors Written 0x01 0x020 6 2000039 --- Number of Write Commands 0x01 0x028 6 697441773 --- Logical Sectors Read 0x01 0x030 6 3665147 --- Number of Read Commands 0x01 0x038 6 88189200000 --- Date and Time TimeStamp 0x02 ===== = = === == Free-Fall Statistics (rev 1) == 0x02 0x010 4 0 --- Overlimit Shock Events 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 636 --- Spindle Motor Power-on Hours 0x03 0x010 4 981 --- Head Flying Hours 0x03 0x018 4 1055 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 6 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x03 0x040 4 7 --- Number of High Priority Unload Events 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 25 --- Current Temperature 0x05 0x010 1 27 N-- Average Short Term Temperature 0x05 0x018 1 25 N-- Average Long Term Temperature 0x05 0x020 1 38 --- Highest Temperature 0x05 0x028 1 7 --- Lowest Temperature 0x05 0x030 1 33 N-- Highest Average Short Term Temperature 0x05 0x038 1 20 N-- Lowest Average Short Term Temperature 0x05 0x040 1 30 N-- Highest Average Long Term Temperature 0x05 0x048 1 23 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 1819 --- Number of Hardware Resets 0x06 0x010 4 1134 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 108689 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 107 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sde smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.14.1-300.fc42.x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Green Device Model: WDC WD30EZRX-00AZ6B0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Apr 10 07:29:44 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (50760) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 488) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 242 242 021 - 9866 4 Start_Stop_Count -O--CK 100 100 000 - 204 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 001 001 000 - 101727 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 202 192 Power-Off_Retract_Count -O--CK 200 200 000 - 108 193 Load_Cycle_Count -O--CK 001 001 000 - 5679324 194 Temperature_Celsius -O---K 125 117 000 - 27 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 22/30 Celsius Lifetime Min/Max Temperature: 0/35 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (62) Index Estimated Time Temperature Celsius 63 2025-04-09 23:32 28 ********* ... ..(203 skipped). .. ********* 267 2025-04-10 02:56 28 ********* 268 2025-04-10 02:57 27 ******** ... ..(141 skipped). .. ******** 410 2025-04-10 05:19 27 ******** 411 2025-04-10 05:20 29 ********** ... ..( 12 skipped). .. ********** 424 2025-04-10 05:33 29 ********** 425 2025-04-10 05:34 28 ********* ... ..(114 skipped). .. ********* 62 2025-04-10 07:29 28 ********* SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 10623 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 67 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 10316930 Vendor specific /dev/sdf smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.14.1-300.fc42.x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD40EZRZ-00GXCB0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5528 ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Apr 10 07:29:45 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (44340) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 470) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 164 163 021 - 6791 4 Start_Stop_Count -O--CK 100 100 000 - 64 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 079 078 000 - 15532 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 64 192 Power-Off_Retract_Count -O--CK 200 200 000 - 8 193 Load_Cycle_Count -O--CK 196 196 000 - 12250 194 Temperature_Celsius -O---K 126 116 000 - 24 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 56 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 24 Celsius Power Cycle Min/Max Temperature: 22/28 Celsius Lifetime Min/Max Temperature: 12/34 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (80) Index Estimated Time Temperature Celsius 81 2025-04-09 23:32 25 ****** ... ..(233 skipped). .. ****** 315 2025-04-10 03:26 25 ****** 316 2025-04-10 03:27 24 ***** 317 2025-04-10 03:28 24 ***** 318 2025-04-10 03:29 24 ***** 319 2025-04-10 03:30 26 ******* ... ..(199 skipped). .. ******* 41 2025-04-10 06:50 26 ******* 42 2025-04-10 06:51 25 ****** ... ..( 37 skipped). .. ****** 80 2025-04-10 07:29 25 ****** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 64 --- Lifetime Power-On Resets 0x01 0x010 4 15532 --- Power-on Hours 0x01 0x018 6 4368529433 --- Logical Sectors Written 0x01 0x020 6 3134501 --- Number of Write Commands 0x01 0x028 6 3628182198 --- Logical Sectors Read 0x01 0x030 6 3574975 --- Number of Read Commands 0x01 0x038 6 80625152 --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 47542 --- Spindle Motor Power-on Hours 0x03 0x010 4 503 --- Head Flying Hours 0x03 0x018 4 12259 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x03 0x040 4 8 --- Number of High Priority Unload Events 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 24 --- Current Temperature 0x05 0x010 1 25 --- Average Short Term Temperature 0x05 0x018 1 24 --- Average Long Term Temperature 0x05 0x020 1 33 --- Highest Temperature 0x05 0x028 1 18 --- Lowest Temperature 0x05 0x030 1 30 --- Highest Average Short Term Temperature 0x05 0x038 1 18 --- Lowest Average Short Term Temperature 0x05 0x040 1 28 --- Highest Average Long Term Temperature 0x05 0x048 1 20 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 5691 --- Number of Hardware Resets 0x06 0x010 4 3307 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 87 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 129 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 10317022 Vendor specific