/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Device Model: WDC WD800BB-00FJA0 Serial Number: -- Firmware Version: 13.03G13 User Capacity: 80,023,182,848 bytes [80.0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-6 (minor revision not indicated) Local Time is: Fri Jun 1 10:45:07 2018 +09 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2460) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 35) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 199 197 051 - 20963 3 Spin_Up_Time POS--- 102 099 021 - 2241 4 Start_Stop_Count -O--CK 097 097 040 - 3753 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate PO-R-- 200 200 051 - 0 9 Power_On_Hours -O--CK 080 080 000 - 15178 10 Spin_Retry_Count PO--C- 100 100 051 - 0 11 Calibration_Retry_Count PO--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3290 194 Temperature_Celsius -O---K 103 006 000 - 40 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable -O--C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 27 200 Multi_Zone_Error_Rate P--R-- 200 199 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning Read SMART Log Directory failed: scsi error badly formed scsi parameters General Purpose Log Directory not supported SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 No Errors Logged SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) not supported /dev/sdb === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.12 Device Model: ST3750528AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC38 User Capacity: 750,156,374,016 bytes [750 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Jun 1 10:45:07 2018 +09 ==> WARNING: A firmware update for this drive may be available, see the following Seagate web pages: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/213891en SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 0 (vendor specific), recommended: 254 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 138) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 117 099 006 - 150785444 3 Spin_Up_Time PO---- 095 095 000 - 0 4 Start_Stop_Count -O--CK 097 097 020 - 3824 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 075 060 030 - 40314741 9 Power_On_Hours -O--CK 097 097 000 - 2860 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 099 099 020 - 2043 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 001 001 099 NOW 1649 187 Reported_Uncorrect -O--CK 053 053 000 - 47 188 Command_Timeout -O--CK 100 001 000 - 661435318550 189 High_Fly_Writes -O-RCK 098 098 000 - 2 190 Airflow_Temperature_Cel -O---K 065 053 045 - 35 (Min/Max 33/35) 194 Temperature_Celsius -O---K 035 047 000 - 35 195 Hardware_ECC_Recovered -O-RC- 035 031 000 - 150785444 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 001 000 - 10417663 240 Head_Flying_Hours ------ 100 253 000 - 5747 (246 91 0) 241 Total_LBAs_Written ------ 100 253 000 - 3105183565 242 Total_LBAs_Read ------ 100 253 000 - 1521233832 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbd GPL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 367 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 367 [6] occurred at disk power-on lifetime: 1779 hours (74 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 28 00 03 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 00 00 00:17:15.911 FLUSH CACHE EXT 25 d8 00 00 08 00 00 bb 00 65 b8 40 00 00:17:15.911 READ DMA EXT 25 d8 00 00 60 00 00 bb 00 65 50 40 00 00:17:15.905 READ DMA EXT 25 d8 00 00 08 00 00 1b 00 61 b8 40 00 00:17:15.902 READ DMA EXT 25 d8 00 00 10 00 00 1c 00 5f 50 40 00 00:17:15.901 READ DMA EXT Error 366 [5] occurred at disk power-on lifetime: 1774 hours (73 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 e6 00 5f c7 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 00 00 00:36:22.305 FLUSH CACHE EXT 25 d8 00 00 08 00 00 e6 00 5f 08 40 00 00:36:22.305 READ DMA EXT 25 d8 00 00 08 00 00 e6 00 5f 00 40 00 00:36:22.305 READ DMA EXT 25 d8 00 00 08 00 00 e5 00 5f f8 40 00 00:36:22.304 READ DMA EXT 25 d8 00 00 08 00 00 e5 00 5f f0 40 00 00:36:22.304 READ DMA EXT Error 365 [4] occurred at disk power-on lifetime: 1773 hours (73 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 87 00 80 81 40 00 Device Fault; Error: ABRT 4 sectors at LBA = 0x87008081 = 2264957057 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 d1 00 05 30 40 00 00:09:05.337 READ DMA EXT 35 00 00 00 08 00 00 ef 00 c4 60 40 00 00:09:05.159 WRITE DMA EXT 35 00 00 00 78 00 00 5c 00 09 18 40 00 00:09:05.100 WRITE DMA EXT 35 00 00 00 08 00 06 3a 00 76 60 40 00 00:09:04.988 WRITE DMA EXT 35 00 00 00 0a 00 00 15 00 1a 30 40 00 00:09:04.987 WRITE DMA EXT Error 364 [3] occurred at disk power-on lifetime: 1773 hours (73 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 87 00 80 81 40 00 Device Fault; Error: ABRT 4 sectors at LBA = 0x87008081 = 2264957057 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 08 00 00 ef 00 c4 60 40 00 00:09:05.159 WRITE DMA EXT 35 00 00 00 78 00 00 5c 00 09 18 40 00 00:09:05.100 WRITE DMA EXT 35 00 00 00 08 00 06 3a 00 76 60 40 00 00:09:04.988 WRITE DMA EXT 35 00 00 00 0a 00 00 15 00 1a 30 40 00 00:09:04.987 WRITE DMA EXT 25 00 00 00 01 00 00 35 00 0e 3f 40 00 00:09:04.461 READ DMA EXT Error 363 [2] occurred at disk power-on lifetime: 1773 hours (73 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 87 00 80 81 40 00 Device Fault; Error: ABRT 4 sectors at LBA = 0x87008081 = 2264957057 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 78 00 00 5c 00 09 18 40 00 00:09:05.100 WRITE DMA EXT 35 00 00 00 08 00 06 3a 00 76 60 40 00 00:09:04.988 WRITE DMA EXT 35 00 00 00 0a 00 00 15 00 1a 30 40 00 00:09:04.987 WRITE DMA EXT 25 00 00 00 01 00 00 35 00 0e 3f 40 00 00:09:04.461 READ DMA EXT 35 00 00 00 20 00 00 1c 00 5f 50 40 00 00:09:04.414 WRITE DMA EXT Error 362 [1] occurred at disk power-on lifetime: 1773 hours (73 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 87 00 80 81 40 00 Device Fault; Error: ABRT 4 sectors at LBA = 0x87008081 = 2264957057 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 08 00 06 3a 00 76 60 40 00 00:09:04.988 WRITE DMA EXT 35 00 00 00 0a 00 00 15 00 1a 30 40 00 00:09:04.987 WRITE DMA EXT 25 00 00 00 01 00 00 35 00 0e 3f 40 00 00:09:04.461 READ DMA EXT 35 00 00 00 20 00 00 1c 00 5f 50 40 00 00:09:04.414 WRITE DMA EXT 25 00 00 00 12 00 00 8d 00 09 a6 40 00 00:09:04.375 READ DMA EXT Error 361 [0] occurred at disk power-on lifetime: 1773 hours (73 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 87 00 80 81 40 00 Device Fault; Error: ABRT 4 sectors at LBA = 0x87008081 = 2264957057 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 0a 00 00 15 00 1a 30 40 00 00:09:04.987 WRITE DMA EXT 25 00 00 00 01 00 00 35 00 0e 3f 40 00 00:09:04.461 READ DMA EXT 35 00 00 00 20 00 00 1c 00 5f 50 40 00 00:09:04.414 WRITE DMA EXT 25 00 00 00 12 00 00 8d 00 09 a6 40 00 00:09:04.375 READ DMA EXT 25 00 00 00 f8 00 00 d5 00 05 30 40 00 00:09:04.340 READ DMA EXT Error 360 [19] occurred at disk power-on lifetime: 1773 hours (73 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 87 00 80 81 40 00 Device Fault; Error: ABRT 4 sectors at LBA = 0x87008081 = 2264957057 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 35 00 0e 3f 40 00 00:09:04.461 READ DMA EXT 35 00 00 00 20 00 00 1c 00 5f 50 40 00 00:09:04.414 WRITE DMA EXT 25 00 00 00 12 00 00 8d 00 09 a6 40 00 00:09:04.375 READ DMA EXT 25 00 00 00 f8 00 00 d5 00 05 30 40 00 00:09:04.340 READ DMA EXT 25 00 00 01 00 00 00 d4 00 05 30 40 00 00:09:04.338 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 33/35 Celsius Lifetime Min/Max Temperature: 0/47 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (37) Index Estimated Time Temperature Celsius 38 2018-05-27 05:01 27 ******** 39 2018-05-27 06:00 ? - 40 2018-05-27 06:59 37 ****************** 41 2018-05-27 07:58 ? - 42 2018-05-27 08:57 38 ******************* 43 2018-05-27 09:56 ? - 44 2018-05-27 10:55 38 ******************* 45 2018-05-27 11:54 38 ******************* 46 2018-05-27 12:53 ? - 47 2018-05-27 13:52 22 *** 48 2018-05-27 14:51 22 *** 49 2018-05-27 15:50 ? - 50 2018-05-27 16:49 37 ****************** 51 2018-05-27 17:48 37 ****************** 52 2018-05-27 18:47 ? - 53 2018-05-27 19:46 32 ************* 54 2018-05-27 20:45 ? - 55 2018-05-27 21:44 23 **** 56 2018-05-27 22:43 ? - 57 2018-05-27 23:42 24 ***** 58 2018-05-28 00:41 ? - 59 2018-05-28 01:40 25 ****** 60 2018-05-28 02:39 ? - 61 2018-05-28 03:38 25 ****** 62 2018-05-28 04:37 ? - 63 2018-05-28 05:36 27 ******** 64 2018-05-28 06:35 ? - 65 2018-05-28 07:34 27 ******** 66 2018-05-28 08:33 ? - 67 2018-05-28 09:32 27 ******** 68 2018-05-28 10:31 ? - 69 2018-05-28 11:30 28 ********* 70 2018-05-28 12:29 ? - 71 2018-05-28 13:28 28 ********* 72 2018-05-28 14:27 28 ********* 73 2018-05-28 15:26 36 ***************** 74 2018-05-28 16:25 ? - 75 2018-05-28 17:24 22 *** 76 2018-05-28 18:23 22 *** 77 2018-05-28 19:22 34 *************** 78 2018-05-28 20:21 34 *************** 79 2018-05-28 21:20 35 **************** 80 2018-05-28 22:19 35 **************** 81 2018-05-28 23:18 ? - 82 2018-05-29 00:17 33 ************** 83 2018-05-29 01:16 ? - 84 2018-05-29 02:15 24 ***** 85 2018-05-29 03:14 ? - 86 2018-05-29 04:13 26 ******* 87 2018-05-29 05:12 ? - 88 2018-05-29 06:11 30 *********** 89 2018-05-29 07:10 30 *********** 90 2018-05-29 08:09 ? - 91 2018-05-29 09:08 27 ******** 92 2018-05-29 10:07 ? - 93 2018-05-29 11:06 28 ********* 94 2018-05-29 12:05 ? - 95 2018-05-29 13:04 31 ************ 96 2018-05-29 14:03 ? - 97 2018-05-29 15:02 32 ************* 98 2018-05-29 16:01 ? - 99 2018-05-29 17:00 30 *********** 100 2018-05-29 17:59 ? - 101 2018-05-29 18:58 24 ***** 102 2018-05-29 19:57 24 ***** 103 2018-05-29 20:56 33 ************** 104 2018-05-29 21:55 ? - 105 2018-05-29 22:54 28 ********* 106 2018-05-29 23:53 ? - 107 2018-05-30 00:52 25 ****** 108 2018-05-30 01:51 25 ****** 109 2018-05-30 02:50 33 ************** 110 2018-05-30 03:49 ? - 111 2018-05-30 04:48 25 ****** 112 2018-05-30 05:47 25 ****** 113 2018-05-30 06:46 35 **************** 114 2018-05-30 07:45 35 **************** 115 2018-05-30 08:44 36 ***************** 116 2018-05-30 09:43 36 ***************** 117 2018-05-30 10:42 ? - 118 2018-05-30 11:41 36 ***************** 119 2018-05-30 12:40 ? - 120 2018-05-30 13:39 32 ************* 121 2018-05-30 14:38 ? - 122 2018-05-30 15:37 34 *************** 123 2018-05-30 16:36 ? - 124 2018-05-30 17:35 26 ******* 125 2018-05-30 18:34 26 ******* 126 2018-05-30 19:33 ? - 127 2018-05-30 20:32 35 **************** 0 2018-05-30 21:31 35 **************** 1 2018-05-30 22:30 35 **************** 2 2018-05-30 23:29 34 *************** 3 2018-05-31 00:28 ? - 4 2018-05-31 01:27 26 ******* 5 2018-05-31 02:26 26 ******* 6 2018-05-31 03:25 36 ***************** 7 2018-05-31 04:24 ? - 8 2018-05-31 05:23 35 **************** 9 2018-05-31 06:22 ? - 10 2018-05-31 07:21 28 ********* 11 2018-05-31 08:20 ? - 12 2018-05-31 09:19 31 ************ 13 2018-05-31 10:18 ? - 14 2018-05-31 11:17 31 ************ 15 2018-05-31 12:16 ? - 16 2018-05-31 13:15 27 ******** 17 2018-05-31 14:14 ? - 18 2018-05-31 15:13 33 ************** 19 2018-05-31 16:12 ? - 20 2018-05-31 17:11 34 *************** 21 2018-05-31 18:10 ? - 22 2018-05-31 19:09 34 *************** 23 2018-05-31 20:08 ? - 24 2018-05-31 21:07 34 *************** 25 2018-05-31 22:06 34 *************** 26 2018-05-31 23:05 ? - 27 2018-06-01 00:04 35 **************** 28 2018-06-01 01:03 ? - 29 2018-06-01 02:02 35 **************** 30 2018-06-01 03:01 35 **************** 31 2018-06-01 04:00 34 *************** 32 2018-06-01 04:59 34 *************** 33 2018-06-01 05:58 33 ************** 34 2018-06-01 06:57 34 *************** ... ..( 2 skipped). .. *************** 37 2018-06-01 09:54 34 *************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS