/dev/sda,megaraid_disk_00 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.16-19-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HGST Product: HUH721010AL5200 Revision: LS03 Compliance: SPC-4 User Capacity: 9,796,820,402,176 bytes [9.79 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000cca2517912d4 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Nov 20 15:19:19 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 21 C Drive Trip Temperature: 50 C Manufactured in week 04 of year 2017 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 66 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 2193 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 14660324699406336 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 1246 0 2037 5787373 140751.561 0 write: 0 0 0 0 39243 49168.073 0 verify: 0 0 0 0 67858 0.786 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background long Completed 96 1120 - [- - -] # 2 Background short Completed 96 1089 - [- - -] # 3 Background short Completed 96 1087 - [- - -] # 4 Background short Completed 96 5 - [- - -] # 5 Reserved(7) Completed 64 5 - [- - -] Long (extended) Self-test duration: 71160 seconds [19.8 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 51330:42 [3079842 minutes] Number of background scans performed: 314, scan progress: 0.00% Number of background medium scans performed: 314 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000cca2517912d5 attached SAS address = 0x500056b3575121ff attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca2517912d6 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_01 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.16-19-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HGST Product: HUH721010AL5200 Revision: LS03 Compliance: SPC-4 User Capacity: 9,796,820,402,176 bytes [9.79 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000cca2517018a0 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Nov 20 15:19:20 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 21 C Drive Trip Temperature: 50 C Manufactured in week 04 of year 2017 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 33 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 2241 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 43679366646857728 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 2554 0 5329 6706593 383116.561 0 write: 0 0 0 0 312919 136561.317 0 verify: 0 0 0 0 374591 0.820 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 96 4 - [- - -] # 2 Reserved(7) Completed 64 3 - [- - -] Long (extended) Self-test duration: 67560 seconds [18.8 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 53563:00 [3213780 minutes] Number of background scans performed: 321, scan progress: 0.00% Number of background medium scans performed: 321 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000cca2517018a1 attached SAS address = 0x500056b3575121ff attached phy identifier = 1 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca2517018a2 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_02 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.16-19-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HGST Product: HUH721010AL5200 Revision: LS03 Compliance: SPC-4 User Capacity: 9,796,820,402,176 bytes [9.79 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000cca2516638f0 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Nov 20 15:19:20 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 21 C Drive Trip Temperature: 50 C Manufactured in week 04 of year 2017 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 365 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 2573 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 23771043202072576 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 60 0 303 9169456 199926.562 0 write: 0 0 0 0 60875 78368.712 0 verify: 0 0 0 0 69959 0.820 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 96 4 - [- - -] # 2 Reserved(7) Completed 64 3 - [- - -] Long (extended) Self-test duration: 67980 seconds [18.9 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 53995:30 [3239730 minutes] Number of background scans performed: 318, scan progress: 0.00% Number of background medium scans performed: 318 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000cca2516638f1 attached SAS address = 0x500056b3575121ff attached phy identifier = 2 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca2516638f2 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_03 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.16-19-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HGST Product: HUH721010AL5200 Revision: LS03 Compliance: SPC-4 User Capacity: 9,796,820,402,176 bytes [9.79 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000cca2517b3130 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Nov 20 15:19:20 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 21 C Drive Trip Temperature: 50 C Manufactured in week 04 of year 2017 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 49 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 2256 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 39625257912369152 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 10809 0 44401 7737933 409522.143 0 write: 0 0 0 5 93727 125926.017 0 verify: 0 0 0 0 597909 0.820 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 96 4 - [- - -] # 2 Reserved(7) Completed 64 3 - [- - -] Long (extended) Self-test duration: 68520 seconds [19.0 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 53556:55 [3213415 minutes] Number of background scans performed: 320, scan progress: 0.00% Number of background medium scans performed: 320 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000cca2517b3131 attached SAS address = 0x500056b3575121ff attached phy identifier = 3 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca2517b3132 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_04 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.16-19-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HGST Product: HUH721010AL5200 Revision: LS03 Compliance: SPC-4 User Capacity: 9,796,820,402,176 bytes [9.79 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000cca2517d7008 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Nov 20 15:19:20 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 21 C Drive Trip Temperature: 50 C Manufactured in week 04 of year 2017 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 57 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 2186 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 13666632475869184 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 294 0 775 6964152 111160.597 0 write: 0 0 0 0 48653 44831.763 0 verify: 0 0 0 0 74054 0.854 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 96 4 - [- - -] # 2 Reserved(7) Completed 64 3 - [- - -] Long (extended) Self-test duration: 64709 seconds [18.0 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 51333:01 [3079981 minutes] Number of background scans performed: 308, scan progress: 0.00% Number of background medium scans performed: 308 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000cca2517d7009 attached SAS address = 0x500056b3575121ff attached phy identifier = 4 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca2517d700a attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_05 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.16-19-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HGST Product: HUH721010AL5200 Revision: LS03 Compliance: SPC-4 User Capacity: 9,796,820,402,176 bytes [9.79 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000cca2517d8d34 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Nov 20 15:19:20 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 21 C Drive Trip Temperature: 50 C Manufactured in week 04 of year 2017 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 40 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 2248 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 37700021256192000 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 1751 0 4339 12211424 560294.690 0 write: 0 0 0 0 137108 116816.603 0 verify: 0 0 0 0 161763 0.820 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 96 7 - [- - -] # 2 Reserved(7) Completed 64 7 - [- - -] Long (extended) Self-test duration: 64437 seconds [17.9 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 53565:19 [3213919 minutes] Number of background scans performed: 305, scan progress: 0.00% Number of background medium scans performed: 305 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000cca2517d8d35 attached SAS address = 0x500056b3575121ff attached phy identifier = 5 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca2517d8d36 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_06 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.16-19-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HGST Product: HUH721010AL5200 Revision: LS03 Compliance: SPC-4 User Capacity: 9,796,820,402,176 bytes [9.79 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000cca2517d867c Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Nov 20 15:19:20 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 21 C Drive Trip Temperature: 50 C Manufactured in week 04 of year 2017 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 49 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 2249 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 41687185660837888 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 12190 0 56848 10198636 406957.932 0 write: 0 0 0 0 289309 123726.854 0 verify: 0 0 0 0 558311 0.820 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 96 4 - [- - -] # 2 Reserved(7) Completed 64 4 - [- - -] Long (extended) Self-test duration: 69360 seconds [19.3 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 53557:54 [3213474 minutes] Number of background scans performed: 321, scan progress: 0.00% Number of background medium scans performed: 321 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000cca2517d867d attached SAS address = 0x500056b3575121ff attached phy identifier = 6 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca2517d867e attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_07 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.16-19-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HGST Product: HUH721010AL5200 Revision: LS03 Compliance: SPC-4 User Capacity: 9,796,820,402,176 bytes [9.79 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000cca2517d6fc0 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Nov 20 15:19:20 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 21 C Drive Trip Temperature: 50 C Manufactured in week 04 of year 2017 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 49 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 2249 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 57305987459055616 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 2300 0 5672 8341766 327163.766 0 write: 0 0 0 1 132797 136286.935 0 verify: 0 0 0 0 158110 0.820 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 96 4 - [- - -] # 2 Reserved(7) Completed 64 4 - [- - -] Long (extended) Self-test duration: 64032 seconds [17.8 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 53558:02 [3213482 minutes] Number of background scans performed: 319, scan progress: 0.00% Number of background medium scans performed: 319 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000cca2517d6fc1 attached SAS address = 0x500056b3575121ff attached phy identifier = 7 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca2517d6fc2 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_08 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.16-19-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HGST Product: HUH721010AL5200 Revision: LS03 Compliance: SPC-4 User Capacity: 9,796,820,402,176 bytes [9.79 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000cca2517afbd4 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Nov 20 15:19:21 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 21 C Drive Trip Temperature: 50 C Manufactured in week 04 of year 2017 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 33 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 2240 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 33669083903819776 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 423 0 1021 10122344 477321.729 0 write: 0 0 0 0 139451 108096.902 0 verify: 0 0 0 0 122226 0.820 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 96 4 - [- - -] # 2 Reserved(7) Completed 64 3 - [- - -] Long (extended) Self-test duration: 68400 seconds [19.0 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 53562:20 [3213740 minutes] Number of background scans performed: 314, scan progress: 0.00% Number of background medium scans performed: 314 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000cca2517afbd5 attached SAS address = 0x500056b3575121ff attached phy identifier = 8 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca2517afbd6 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_09 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.16-19-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HGST Product: HUH721010AL5200 Revision: LS03 Compliance: SPC-4 User Capacity: 9,796,820,402,176 bytes [9.79 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000cca2517d8ffc Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Nov 20 15:19:21 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 21 C Drive Trip Temperature: 50 C Manufactured in week 04 of year 2017 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 57 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 2179 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 25439970772647936 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 4475 0 12965 8119988 251778.310 0 write: 0 0 0 0 36952 80618.031 0 verify: 0 0 0 0 135554 0.820 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 96 4 - [- - -] # 2 Reserved(7) Completed 64 3 - [- - -] Long (extended) Self-test duration: 66180 seconds [18.4 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 51333:14 [3079994 minutes] Number of background scans performed: 305, scan progress: 0.00% Number of background medium scans performed: 305 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000cca2517d8ffd attached SAS address = 0x500056b3575121ff attached phy identifier = 9 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca2517d8ffe attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_10 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.16-19-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HGST Product: HUH721010AL5200 Revision: LS03 Compliance: SPC-4 User Capacity: 9,796,820,402,176 bytes [9.79 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000cca2517b17d0 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Nov 20 15:19:21 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 21 C Drive Trip Temperature: 50 C Manufactured in week 04 of year 2017 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 66 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 2190 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 20785676110790656 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 178 0 438 8785274 170400.874 0 write: 0 0 0 0 33352 70162.011 0 verify: 0 0 0 0 32229 0.820 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background long Completed 96 1120 - [- - -] # 2 Background short Completed 96 1089 - [- - -] # 3 Background short Completed 96 1088 - [- - -] # 4 Background short Completed 96 5 - [- - -] # 5 Reserved(7) Completed 64 5 - [- - -] Long (extended) Self-test duration: 64483 seconds [17.9 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 51331:27 [3079887 minutes] Number of background scans performed: 309, scan progress: 0.00% Number of background medium scans performed: 309 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000cca2517b17d1 attached SAS address = 0x500056b3575121ff attached phy identifier = 10 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca2517b17d2 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_11 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.16-19-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HGST Product: HUH721010AL5200 Revision: LS03 Compliance: SPC-4 User Capacity: 9,796,820,402,176 bytes [9.79 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000cca2517aa614 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Nov 20 15:19:21 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 21 C Drive Trip Temperature: 50 C Manufactured in week 04 of year 2017 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 37 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 2237 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 40861853772939264 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 2130 0 4410 7655957 276779.481 0 write: 0 0 0 0 265561 110935.501 0 verify: 0 0 0 0 131221 0.854 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 96 4 - [- - -] # 2 Reserved(7) Completed 64 4 - [- - -] Long (extended) Self-test duration: 65368 seconds [18.2 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 53563:06 [3213786 minutes] Number of background scans performed: 320, scan progress: 0.00% Number of background medium scans performed: 320 # when lba(hex) [sk,asc,ascq] reassign_status 1 53473:39 000000000992ac38 [3,11,0] Require Write or Reassign Blocks command 2 53473:38 0000000008421218 [3,11,0] Require Write or Reassign Blocks command 3 53473:38 0000000008370628 [3,11,0] Require Write or Reassign Blocks command 4 53473:34 00000000058a8c68 [3,11,0] Require Write or Reassign Blocks command 5 53473:34 000000000580dbf0 [3,11,0] Require Write or Reassign Blocks command 6 53473:34 000000000580dbe8 [3,11,0] Require Write or Reassign Blocks command 7 53473:24 00000000016cc5f0 [3,11,0] Recovered via rewrite in-place 8 53473:22 00000000001cad00 [1,18,2] Successfully reassigned Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000cca2517aa615 attached SAS address = 0x500056b3575121ff attached phy identifier = 11 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca2517aa616 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0