/dev/sda,megaraid_disk_04 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.1.67-gentoo-x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: NETAPP Product: X477_HMKPX04TA07 Revision: NA00 Compliance: SPC-4 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Logical block size: 512 bytes LU is resource provisioned, LBPRZ=0 Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000cca07397ae04 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Jan 15 05:54:06 2024 -00 SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 55 C Drive Trip Temperature: 85 C Manufactured in week 17 of year 2016 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 387 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 1842 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 417927211778048 Vendor (Seagate/Hitachi) factory information number of hours powered up = 43772.37 number of minutes until next internal SMART test = 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 14583 0 2 0 163220 5336.290 0 write: 0 0 0 0 10934 2273.759 0 verify: 1695072 0 4 0 84077 167697.803 0 Non-medium error count: 1278 No Self-tests have been logged Background scan results log Status: no scans active Accumulated power on time, hours:minutes 43772:22 [2626342 minutes] Number of background scans performed: 0, scan progress: 0.00% Number of background medium scans performed: 0 General statistics and performance log page: General access statistics and performance: Number of read commands: 46318914 Number of write commands: 24910405 number of logical blocks received: 10422444161 number of logical blocks transmitted: 4440935379 read command processing intervals: 0 write command processing intervals: 0 weighted number of read commands plus write commands: 0 weighted read command processing plus write command processing: 0 Idle time: Idle time intervals: 2975829279 in seconds: 148791463.950 in hours: 41330.962 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 4 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca07397ae05 attached SAS address = 0x5b8ca3a0ea9c3602 attached phy identifier = 3 Invalid DWORD count = 101 Running disparity error count = 96 Loss of DWORD synchronization count = 34 Phy reset problem count = 0 relative target port id = 2 generation code = 4 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca07397ae06 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_05 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.1.67-gentoo-x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: NETAPP Product: X477_HMKPX04TA07 Revision: NA00 Compliance: SPC-4 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Logical block size: 512 bytes LU is resource provisioned, LBPRZ=0 Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000cca07301b0c4 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Jan 15 05:54:07 2024 -00 SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 50 C Drive Trip Temperature: 85 C Manufactured in week 13 of year 2015 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 399 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 2142 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 12093272876908544 Vendor (Seagate/Hitachi) factory information number of hours powered up = 42962.37 number of minutes until next internal SMART test = 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 5957526 9 1 0 3496217 82521.767 0 write: 0 0 0 0 259696 71545.818 0 verify: 5228399 26 1 0 24460 122616.458 0 Non-medium error count: 1255 No Self-tests have been logged Background scan results log Status: no scans active Accumulated power on time, hours:minutes 42962:22 [2577742 minutes] Number of background scans performed: 0, scan progress: 0.00% Number of background medium scans performed: 0 General statistics and performance log page: General access statistics and performance: Number of read commands: 1732777319 Number of write commands: 720815234 number of logical blocks received: 161175325393 number of logical blocks transmitted: 139737925381 read command processing intervals: 0 write command processing intervals: 0 weighted number of read commands plus write commands: 0 weighted read command processing plus write command processing: 0 Idle time: Idle time intervals: 2564606126 in seconds: 128230306.300 in hours: 35619.529 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 4 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca07301b0c5 attached SAS address = 0x5b8ca3a0ea9c3601 attached phy identifier = 2 Invalid DWORD count = 115 Running disparity error count = 108 Loss of DWORD synchronization count = 37 Phy reset problem count = 0 relative target port id = 2 generation code = 4 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca07301b0c6 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_06 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.1.67-gentoo-x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: HITACHI HUS724040ALE640 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: MJAONS04 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database 7.3/5528 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jan 15 05:54:07 2024 -00 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (33171) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 553) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 100 100 054 - 0 3 Spin_Up_Time POS--- 201 201 024 - 334 (Average 437) 4 Start_Stop_Count -O--C- 100 100 000 - 570 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 100 100 020 - 0 9 Power_On_Hours -O--C- 097 097 000 - 27170 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 506 192 Power-Off_Retract_Count -O--CK 100 100 000 - 712 193 Load_Cycle_Count -O--C- 100 100 000 - 712 194 Temperature_Celsius -O---- 111 111 000 - 54 (Min/Max 19/66) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 3044 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 256 Current Device Internal Status Data log 0x25 GPL R/O 256 Saved Device Internal Status Data log 0x80 GPL R/W 63 Host vendor specific log 0x81-0x9f GPL,SL R/W 16 Host vendor specific log 0xa2 GPL VS 1 Device vendor specific log 0xb2 GPL VS 63 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 3044 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3044 [3] occurred at disk power-on lifetime: 26947 hours (1122 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 31 00 00 03 f3 ad af 03 00 Error: ICRC, ABRT at LBA = 0x03f3adaf = 66301359 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 00 00 00 03 f3 ad 60 40 00 01:43:38.374 READ FPDMA QUEUED 60 00 80 00 00 00 00 03 f3 ac e0 40 00 01:43:38.374 READ FPDMA QUEUED 60 00 80 00 00 00 00 03 f3 ac 60 40 00 01:43:38.374 READ FPDMA QUEUED 60 00 38 00 00 00 00 03 f3 ac a0 40 00 01:43:38.369 READ FPDMA QUEUED 60 00 40 00 00 00 00 03 f3 ac d8 40 00 01:43:38.369 READ FPDMA QUEUED Error 3043 [2] occurred at disk power-on lifetime: 26947 hours (1122 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 71 00 00 02 ac 0e 1f 02 00 Error: ICRC, ABRT at LBA = 0x02ac0e1f = 44830239 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 00 00 00 02 ac 0e 10 40 00 01:43:27.015 READ FPDMA QUEUED 60 00 38 00 00 00 00 02 ac 0e 50 40 00 01:43:27.009 READ FPDMA QUEUED 60 00 40 00 00 00 00 02 ac 0e 88 40 00 01:43:27.009 READ FPDMA QUEUED 60 00 40 00 00 00 00 02 ac 0f 28 40 00 01:43:27.005 READ FPDMA QUEUED 60 00 40 00 00 00 00 02 ac 0e 10 40 00 01:43:26.996 READ FPDMA QUEUED Error 3042 [1] occurred at disk power-on lifetime: 26947 hours (1122 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 5a 00 00 03 fd 8b 97 03 00 Error: ICRC, ABRT at LBA = 0x03fd8b97 = 66947991 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 79 00 00 00 00 03 fd 8b 78 40 00 01:42:54.107 READ FPDMA QUEUED 60 00 80 00 00 00 00 03 fd 8a f8 40 00 01:42:54.106 READ FPDMA QUEUED 60 00 80 00 00 00 00 03 fd 8a 78 40 00 01:42:54.106 READ FPDMA QUEUED 60 00 80 00 00 00 00 03 fd 89 f8 40 00 01:42:54.106 READ FPDMA QUEUED 60 00 38 00 00 00 00 03 fd 8a 38 40 00 01:42:54.099 READ FPDMA QUEUED Error 3041 [0] occurred at disk power-on lifetime: 26947 hours (1122 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 e0 32 7f 00 00 Error: ICRC, ABRT at LBA = 0x00e0327f = 14692991 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 00 00 00 00 e0 32 40 40 00 01:42:06.295 READ FPDMA QUEUED 60 00 3a 00 00 00 00 00 e0 89 70 40 00 01:42:06.285 READ FPDMA QUEUED 60 00 40 00 00 00 00 00 e0 31 c8 40 00 01:42:06.282 READ FPDMA QUEUED 60 00 80 00 00 00 00 00 df 74 58 40 00 01:42:06.281 READ FPDMA QUEUED 60 00 80 00 00 00 00 00 df 73 d8 40 00 01:42:06.280 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 54 Celsius Power Cycle Min/Max Temperature: 53/55 Celsius Lifetime Min/Max Temperature: 19/66 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (5) Index Estimated Time Temperature Celsius 6 2024-01-15 03:47 59 **************************************** ... ..( 16 skipped). .. **************************************** 23 2024-01-15 04:04 59 **************************************** 24 2024-01-15 04:05 ? - 25 2024-01-15 04:06 53 ********************************** ... ..( 44 skipped). .. ********************************** 70 2024-01-15 04:51 53 ********************************** 71 2024-01-15 04:52 54 *********************************** 72 2024-01-15 04:53 53 ********************************** ... ..( 3 skipped). .. ********************************** 76 2024-01-15 04:57 53 ********************************** 77 2024-01-15 04:58 54 *********************************** ... ..( 15 skipped). .. *********************************** 93 2024-01-15 05:14 54 *********************************** 94 2024-01-15 05:15 55 ************************************ 95 2024-01-15 05:16 54 *********************************** ... ..( 7 skipped). .. *********************************** 103 2024-01-15 05:24 54 *********************************** 104 2024-01-15 05:25 55 ************************************ 105 2024-01-15 05:26 54 *********************************** ... ..( 27 skipped). .. *********************************** 5 2024-01-15 05:54 54 *********************************** Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 506 --- Lifetime Power-On Resets 0x01 0x018 6 53786148255 --- Logical Sectors Written 0x01 0x020 6 30289193 --- Number of Write Commands 0x01 0x028 6 205158428244 --- Logical Sectors Read 0x01 0x030 6 211300974 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 26652 --- Spindle Motor Power-on Hours 0x03 0x010 4 26652 --- Head Flying Hours 0x03 0x018 4 712 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 2 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 54 --- Current Temperature 0x05 0x010 1 60 N-- Average Short Term Temperature 0x05 0x018 1 45 N-- Average Long Term Temperature 0x05 0x020 1 66 --- Highest Temperature 0x05 0x028 1 19 --- Lowest Temperature 0x05 0x030 1 63 N-- Highest Average Short Term Temperature 0x05 0x038 1 22 N-- Lowest Average Short Term Temperature 0x05 0x040 1 51 N-- Highest Average Long Term Temperature 0x05 0x048 1 23 N-- Lowest Average Long Term Temperature 0x05 0x050 4 1920 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 1427 --- Number of Hardware Resets 0x06 0x010 4 389 --- Number of ASR Events 0x06 0x018 4 3044 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sda,megaraid_disk_07 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.1.67-gentoo-x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: NETAPP Product: X477_HMKPX04TA07 Revision: NA00 Compliance: SPC-4 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Logical block size: 512 bytes LU is resource provisioned, LBPRZ=0 Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000cca073987c50 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Jan 15 05:54:09 2024 -00 SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 51 C Drive Trip Temperature: 85 C Manufactured in week 17 of year 2016 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 420 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 2235 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 4050698715004928 Vendor (Seagate/Hitachi) factory information number of hours powered up = 43774.08 number of minutes until next internal SMART test = 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 35636 1 1 0 2019213 193813.483 0 write: 0 0 0 0 272580 48958.808 0 verify: 1705676 1 1 0 40699 196862.859 0 Non-medium error count: 1257 No Self-tests have been logged Background scan results log Status: no scans active Accumulated power on time, hours:minutes 43774:05 [2626445 minutes] Number of background scans performed: 0, scan progress: 0.00% Number of background medium scans performed: 0 General statistics and performance log page: General access statistics and performance: Number of read commands: 827717394 Number of write commands: 241440458 number of logical blocks received: 378541958055 number of logical blocks transmitted: 95622671774 read command processing intervals: 0 write command processing intervals: 0 weighted number of read commands plus write commands: 0 weighted read command processing plus write command processing: 0 Idle time: Idle time intervals: 2855568350 in seconds: 142778417.500 in hours: 39660.671 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: power on reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca073987c51 attached SAS address = 0x5b8ca3a0ea9c3600 attached phy identifier = 0 Invalid DWORD count = 64 Running disparity error count = 63 Loss of DWORD synchronization count = 20 Phy reset problem count = 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca073987c52 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0