/dev/sda,megaraid_disk_00 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-62-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Lexar 128GB SSD Device Model: Lexar 128GB SSD Serial Number: -- LU WWN Device Id: 5 000000 ... Firmware Version: SN09610 User Capacity: 128,035,676,160 bytes [128 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5528 ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jul 20 10:57:08 2025 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 33) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 85) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 20 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 New_Bad_Blk_Cnt PO--C- 100 100 010 - 0 9 Power_On_Hours -O--C- 100 100 000 - 15805 12 Power_Cycle_Count -O--C- 100 100 000 - 255 164 Unknown_Attribute ------ 100 100 000 - 73033842874 165 Unknown_Attribute ------ 100 100 000 - 296 166 Unknown_Attribute ------ 100 100 000 - 17 167 SSD_Protect_mode -O---K 100 100 000 - 186 194 Temperature_Celsius -O---K 036 036 000 - 36 (Min/Max 16/48) 199 UDMA_CRC_Error_Count -O--C- 100 100 000 - 52 241 Total_LBAs_Written -O--CK 100 100 000 - 129202 242 Total_LBAs_Read -O--CK 100 100 000 - 29796 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 52 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 52 [51] occurred at disk power-on lifetime: 15388 hours (641 days + 4 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:36.600 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:36.600 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:36.400 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:36.400 IDENTIFY DEVICE Error 51 [50] occurred at disk power-on lifetime: 14723 hours (613 days + 11 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:49.500 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:32.100 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.100 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:32.100 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.000 IDENTIFY DEVICE Error 50 [49] occurred at disk power-on lifetime: 14723 hours (613 days + 11 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:34.000 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:34.000 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:33.900 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:33.900 IDENTIFY DEVICE Error 49 [48] occurred at disk power-on lifetime: 14723 hours (613 days + 11 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:33.800 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:33.800 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:33.700 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:33.700 IDENTIFY DEVICE Error 48 [47] occurred at disk power-on lifetime: 14723 hours (613 days + 11 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.500 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:32.100 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.100 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:32.100 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.100 IDENTIFY DEVICE Error 47 [46] occurred at disk power-on lifetime: 14018 hours (584 days + 2 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:36.400 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:36.400 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:36.400 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:36.400 IDENTIFY DEVICE Error 46 [45] occurred at disk power-on lifetime: 13571 hours (565 days + 11 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.500 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:31.200 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:31.200 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:31.100 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:31.100 IDENTIFY DEVICE Error 45 [44] occurred at disk power-on lifetime: 13527 hours (563 days + 15 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:32.000 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.000 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:31.900 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:31.900 IDENTIFY DEVICE SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 6498 - # 2 Extended offline Aborted by host 00% 6496 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: ?/41 Celsius Lifetime Min/Max Temperature: ?/ ? Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 255 --- Lifetime Power-On Resets 0x01 0x010 4 15805 --- Power-on Hours 0x01 0x018 6 8467388267 --- Logical Sectors Written 0x01 0x020 6 144591761 --- Number of Write Commands 0x01 0x028 6 1952766103 --- Logical Sectors Read 0x01 0x030 6 26279770 --- Number of Read Commands 0x01 0x038 6 14203089666724 --- Date and Time TimeStamp 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 39 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 52 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb,megaraid_disk_00 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-62-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Lexar 128GB SSD Device Model: Lexar 128GB SSD Serial Number: -- LU WWN Device Id: 5 000000 ... Firmware Version: SN09610 User Capacity: 128,035,676,160 bytes [128 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5528 ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jul 20 10:57:08 2025 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 33) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 85) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 20 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 New_Bad_Blk_Cnt PO--C- 100 100 010 - 0 9 Power_On_Hours -O--C- 100 100 000 - 15805 12 Power_Cycle_Count -O--C- 100 100 000 - 255 164 Unknown_Attribute ------ 100 100 000 - 73033842874 165 Unknown_Attribute ------ 100 100 000 - 296 166 Unknown_Attribute ------ 100 100 000 - 17 167 SSD_Protect_mode -O---K 100 100 000 - 186 194 Temperature_Celsius -O---K 036 036 000 - 36 (Min/Max 16/48) 199 UDMA_CRC_Error_Count -O--C- 100 100 000 - 52 241 Total_LBAs_Written -O--CK 100 100 000 - 129202 242 Total_LBAs_Read -O--CK 100 100 000 - 29796 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 52 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 52 [51] occurred at disk power-on lifetime: 15388 hours (641 days + 4 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:36.600 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:36.600 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:36.400 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:36.400 IDENTIFY DEVICE Error 51 [50] occurred at disk power-on lifetime: 14723 hours (613 days + 11 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:49.500 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:32.100 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.100 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:32.100 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.000 IDENTIFY DEVICE Error 50 [49] occurred at disk power-on lifetime: 14723 hours (613 days + 11 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:34.000 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:34.000 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:33.900 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:33.900 IDENTIFY DEVICE Error 49 [48] occurred at disk power-on lifetime: 14723 hours (613 days + 11 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:33.800 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:33.800 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:33.700 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:33.700 IDENTIFY DEVICE Error 48 [47] occurred at disk power-on lifetime: 14723 hours (613 days + 11 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.500 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:32.100 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.100 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:32.100 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.100 IDENTIFY DEVICE Error 47 [46] occurred at disk power-on lifetime: 14018 hours (584 days + 2 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:36.400 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:36.400 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:36.400 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:36.400 IDENTIFY DEVICE Error 46 [45] occurred at disk power-on lifetime: 13571 hours (565 days + 11 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.500 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:31.200 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:31.200 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:31.100 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:31.100 IDENTIFY DEVICE Error 45 [44] occurred at disk power-on lifetime: 13527 hours (563 days + 15 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:32.000 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.000 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:31.900 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:31.900 IDENTIFY DEVICE SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 6498 - # 2 Extended offline Aborted by host 00% 6496 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: ?/41 Celsius Lifetime Min/Max Temperature: ?/ ? Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 255 --- Lifetime Power-On Resets 0x01 0x010 4 15805 --- Power-on Hours 0x01 0x018 6 8467388267 --- Logical Sectors Written 0x01 0x020 6 144591761 --- Number of Write Commands 0x01 0x028 6 1952766175 --- Logical Sectors Read 0x01 0x030 6 26279779 --- Number of Read Commands 0x01 0x038 6 14203089666724 --- Date and Time TimeStamp 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 39 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 52 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb,megaraid_disk_01 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-62-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Marvell based SanDisk SSDs Device Model: SanDisk SSD PLUS 480GB Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: 42077100 User Capacity: 480,103,981,056 bytes [480 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: In smartctl database 7.3/5528 ATA Version is: ACS-4, ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jul 20 10:57:08 2025 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 10) minutes. Conveyance self-test routine recommended polling time: ( 1) minutes. SMART Attributes Data Structure revision number: 0 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 241 12 Power_Cycle_Count -O--CK 100 100 000 - 124 165 Total_Write/Erase_Count -O--CK 100 100 000 - 1468910076379 166 Min_W/E_Cycle -O--CK 100 100 000 - 1 167 Min_Bad_Block/Die -O--CK 100 100 000 - 10 168 Maximum_Erase_Cycle -O--CK 100 100 000 - 26 169 Total_Bad_Block -O--CK 100 100 000 - 64 170 Unknown_Marvell_Attr -O--CK 100 100 000 - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Avg_Write/Erase_Count -O--CK 100 100 005 - 10 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 100 100 014 - 32 (Min/Max 20/52) 199 SATA_CRC_Error -O--CK 100 100 000 - 0 230 Perc_Write/Erase_Count -O--CK 100 100 000 - 63 66 63 232 Perc_Avail_Resrvd_Space PO--CK 100 100 004 - 100 233 Total_NAND_Writes_GiB -O--CK 100 100 000 - 5320 234 Perc_Write/Erase_Ct_BC -O--CK 100 100 000 - 5457 241 Total_Writes_GiB ----CK 253 253 000 - 3629 242 Total_Reads_GiB ----CK 253 253 000 - 1795 244 Thermal_Throttle -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3-0xa7 GPL,SL VS 1 Device vendor specific log 0xde GPL,SL VS 1 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (16 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (empty) == 0x05 ===== = = === == Temperature Statistics (empty) == 0x07 ===== = = === == Solid State Device Statistics (empty) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sde,megaraid_disk_00 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-62-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Lexar 128GB SSD Device Model: Lexar 128GB SSD Serial Number: -- LU WWN Device Id: 5 000000 ... Firmware Version: SN09610 User Capacity: 128,035,676,160 bytes [128 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5528 ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jul 20 10:57:08 2025 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 33) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 85) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 20 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 New_Bad_Blk_Cnt PO--C- 100 100 010 - 0 9 Power_On_Hours -O--C- 100 100 000 - 15805 12 Power_Cycle_Count -O--C- 100 100 000 - 255 164 Unknown_Attribute ------ 100 100 000 - 73033842874 165 Unknown_Attribute ------ 100 100 000 - 296 166 Unknown_Attribute ------ 100 100 000 - 17 167 SSD_Protect_mode -O---K 100 100 000 - 186 194 Temperature_Celsius -O---K 036 036 000 - 36 (Min/Max 16/48) 199 UDMA_CRC_Error_Count -O--C- 100 100 000 - 52 241 Total_LBAs_Written -O--CK 100 100 000 - 129202 242 Total_LBAs_Read -O--CK 100 100 000 - 29796 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 52 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 52 [51] occurred at disk power-on lifetime: 15388 hours (641 days + 4 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:36.600 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:36.600 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:36.400 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:36.400 IDENTIFY DEVICE Error 51 [50] occurred at disk power-on lifetime: 14723 hours (613 days + 11 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:49.500 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:32.100 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.100 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:32.100 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.000 IDENTIFY DEVICE Error 50 [49] occurred at disk power-on lifetime: 14723 hours (613 days + 11 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:34.000 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:34.000 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:33.900 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:33.900 IDENTIFY DEVICE Error 49 [48] occurred at disk power-on lifetime: 14723 hours (613 days + 11 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:33.800 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:33.800 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:33.700 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:33.700 IDENTIFY DEVICE Error 48 [47] occurred at disk power-on lifetime: 14723 hours (613 days + 11 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.500 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:32.100 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.100 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:32.100 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.100 IDENTIFY DEVICE Error 47 [46] occurred at disk power-on lifetime: 14018 hours (584 days + 2 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:36.400 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:36.400 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:36.400 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:36.400 IDENTIFY DEVICE Error 46 [45] occurred at disk power-on lifetime: 13571 hours (565 days + 11 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.500 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:31.200 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:31.200 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:31.100 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:31.100 IDENTIFY DEVICE Error 45 [44] occurred at disk power-on lifetime: 13527 hours (563 days + 15 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:32.000 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.000 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:31.900 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:31.900 IDENTIFY DEVICE SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 6498 - # 2 Extended offline Aborted by host 00% 6496 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: ?/41 Celsius Lifetime Min/Max Temperature: ?/ ? Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 255 --- Lifetime Power-On Resets 0x01 0x010 4 15805 --- Power-on Hours 0x01 0x018 6 8467388267 --- Logical Sectors Written 0x01 0x020 6 144591761 --- Number of Write Commands 0x01 0x028 6 1952769519 --- Logical Sectors Read 0x01 0x030 6 26279826 --- Number of Read Commands 0x01 0x038 6 14203089666924 --- Date and Time TimeStamp 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 39 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 52 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sde,megaraid_disk_01 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-62-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Marvell based SanDisk SSDs Device Model: SanDisk SSD PLUS 480GB Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: 42077100 User Capacity: 480,103,981,056 bytes [480 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: In smartctl database 7.3/5528 ATA Version is: ACS-4, ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jul 20 10:57:08 2025 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 10) minutes. Conveyance self-test routine recommended polling time: ( 1) minutes. SMART Attributes Data Structure revision number: 0 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 241 12 Power_Cycle_Count -O--CK 100 100 000 - 124 165 Total_Write/Erase_Count -O--CK 100 100 000 - 1468910076379 166 Min_W/E_Cycle -O--CK 100 100 000 - 1 167 Min_Bad_Block/Die -O--CK 100 100 000 - 10 168 Maximum_Erase_Cycle -O--CK 100 100 000 - 26 169 Total_Bad_Block -O--CK 100 100 000 - 64 170 Unknown_Marvell_Attr -O--CK 100 100 000 - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Avg_Write/Erase_Count -O--CK 100 100 005 - 10 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 100 100 014 - 32 (Min/Max 20/52) 199 SATA_CRC_Error -O--CK 100 100 000 - 0 230 Perc_Write/Erase_Count -O--CK 100 100 000 - 63 66 63 232 Perc_Avail_Resrvd_Space PO--CK 100 100 004 - 100 233 Total_NAND_Writes_GiB -O--CK 100 100 000 - 5320 234 Perc_Write/Erase_Ct_BC -O--CK 100 100 000 - 5457 241 Total_Writes_GiB ----CK 253 253 000 - 3629 242 Total_Reads_GiB ----CK 253 253 000 - 1795 244 Thermal_Throttle -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3-0xa7 GPL,SL VS 1 Device vendor specific log 0xde GPL,SL VS 1 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (16 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (empty) == 0x05 ===== = = === == Temperature Statistics (empty) == 0x07 ===== = = === == Solid State Device Statistics (empty) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sde,megaraid_disk_02 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-62-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Lexar 128GB SSD Device Model: Lexar 128GB SSD Serial Number: -- LU WWN Device Id: 5 000000 ... Firmware Version: SN09610 User Capacity: 128,035,676,160 bytes [128 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5528 ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jul 20 10:57:08 2025 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 33) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 85) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 20 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 New_Bad_Blk_Cnt PO--C- 100 100 010 - 0 9 Power_On_Hours -O--C- 100 100 000 - 16493 12 Power_Cycle_Count -O--C- 100 100 000 - 244 164 Unknown_Attribute ------ 100 100 000 - 38666305631 165 Unknown_Attribute ------ 100 100 000 - 177 166 Unknown_Attribute ------ 100 100 000 - 9 167 SSD_Protect_mode -O---K 100 100 000 - 95 194 Temperature_Celsius -O---K 035 035 000 - 35 (Min/Max 15/48) 199 UDMA_CRC_Error_Count -O--C- 100 100 000 - 0 241 Total_LBAs_Written -O--CK 100 100 000 - 59685 242 Total_LBAs_Read -O--CK 100 100 000 - 21199 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: ? Celsius Power Cycle Min/Max Temperature: ?/ ? Celsius Lifetime Min/Max Temperature: ?/ ? Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 244 --- Lifetime Power-On Resets 0x01 0x010 4 16493 --- Power-on Hours 0x01 0x018 6 3911520765 --- Logical Sectors Written 0x01 0x020 6 73354242 --- Number of Write Commands 0x01 0x028 6 1389359616 --- Logical Sectors Read 0x01 0x030 6 20116207 --- Number of Read Commands 0x01 0x038 6 14686025690876 --- Date and Time TimeStamp 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 23 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sde,megaraid_disk_03 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-62-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Lexar 128GB SSD Device Model: Lexar 128GB SSD Serial Number: -- LU WWN Device Id: 5 000000 ... Firmware Version: SN09610 User Capacity: 128,035,676,160 bytes [128 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5528 ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jul 20 10:57:08 2025 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 33) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 85) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 20 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 New_Bad_Blk_Cnt PO--C- 100 100 010 - 0 9 Power_On_Hours -O--C- 100 100 000 - 17290 12 Power_Cycle_Count -O--C- 100 100 000 - 243 164 Unknown_Attribute ------ 100 100 000 - 55845453921 165 Unknown_Attribute ------ 100 100 000 - 166 166 Unknown_Attribute ------ 100 100 000 - 13 167 SSD_Protect_mode -O---K 100 100 000 - 97 194 Temperature_Celsius -O---K 033 033 000 - 33 (Min/Max 17/44) 199 UDMA_CRC_Error_Count -O--C- 100 100 000 - 88 241 Total_LBAs_Written -O--CK 100 100 000 - 60778 242 Total_LBAs_Read -O--CK 100 100 000 - 25115 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 88 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 88 [87] occurred at disk power-on lifetime: 16743 hours (697 days + 15 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:36.600 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:36.600 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:36.400 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:36.400 IDENTIFY DEVICE Error 87 [86] occurred at disk power-on lifetime: 15855 hours (660 days + 15 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.600 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:32.200 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.200 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:32.100 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.100 IDENTIFY DEVICE Error 86 [85] occurred at disk power-on lifetime: 15854 hours (660 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:34.000 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:34.000 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:33.900 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:33.900 IDENTIFY DEVICE Error 85 [84] occurred at disk power-on lifetime: 15854 hours (660 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:33.500 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:33.500 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:33.400 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:33.400 IDENTIFY DEVICE Error 84 [83] occurred at disk power-on lifetime: 15854 hours (660 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.700 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:32.200 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.100 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:32.100 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.100 IDENTIFY DEVICE Error 83 [82] occurred at disk power-on lifetime: 14929 hours (622 days + 1 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.500 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:36.400 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:36.400 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:36.400 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:36.400 IDENTIFY DEVICE Error 82 [81] occurred at disk power-on lifetime: 14330 hours (597 days + 2 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:31.300 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:31.300 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:31.100 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:31.100 IDENTIFY DEVICE Error 81 [80] occurred at disk power-on lifetime: 14273 hours (594 days + 17 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 00 01 00 00 0e e7 c2 b0 40 00 Error: IDNF at LBA = 0x0ee7c2b0 = 250069680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 0e e7 c2 b0 40 80 00:00:45.400 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 99 00 80 00:00:32.000 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.000 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 00:00:32.000 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 80 00:00:32.000 IDENTIFY DEVICE SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 6179 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: ? Celsius Power Cycle Min/Max Temperature: ?/ ? Celsius Lifetime Min/Max Temperature: ?/ ? Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 243 --- Lifetime Power-On Resets 0x01 0x010 4 17290 --- Power-on Hours 0x01 0x018 6 3983211092 --- Logical Sectors Written 0x01 0x020 6 76805041 --- Number of Write Commands 0x01 0x028 6 1645984829 --- Logical Sectors Read 0x01 0x030 6 22563366 --- Number of Read Commands 0x01 0x038 6 15427668877888 --- Date and Time TimeStamp 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 22 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 88 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sde,megaraid_disk_04 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-62-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K2000 Device Model: Hitachi HDS722020ALA330 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: JKAOA28A User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Jul 20 10:57:08 2025 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 128 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (22330) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 372) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 098 098 016 - 196609 2 Throughput_Performance P-S--- 133 133 054 - 99 3 Spin_Up_Time POS--- 159 159 024 - 474 (Average 434) 4 Start_Stop_Count -O--C- 100 100 000 - 573 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 110 110 020 - 40 9 Power_On_Hours -O--C- 098 098 000 - 20338 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 503 192 Power-Off_Retract_Count -O--CK 100 100 000 - 623 193 Load_Cycle_Count -O--C- 100 100 000 - 623 194 Temperature_Celsius -O---- 120 120 000 - 50 (Min/Max 16/65) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] occurred at disk power-on lifetime: 1175 hours (48 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 7c 00 00 18 ee ac 04 00 00 Error: ICRC, ABRT 124 sectors at LBA = 0x18eeac04 = 418294788 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 80 00 00 18 ee ac 00 e8 00 14:15:09.100 WRITE DMA EXT 35 00 00 00 08 00 00 15 7f e1 40 e5 00 14:15:09.098 WRITE DMA EXT 35 00 00 00 09 00 00 01 60 ab 81 e1 00 14:15:09.096 WRITE DMA EXT 35 00 00 00 08 00 00 4e e7 03 f0 ee 00 14:15:09.095 WRITE DMA EXT 35 00 00 00 08 00 00 4e e7 03 d0 ee 00 14:15:09.093 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 28 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 50 Celsius Power Cycle Min/Max Temperature: 24/56 Celsius Lifetime Min/Max Temperature: 16/65 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 503 --- Lifetime Power-On Resets 0x01 0x010 4 20338 --- Power-on Hours 0x01 0x018 6 32306807151 --- Logical Sectors Written 0x01 0x020 6 347618926 --- Number of Write Commands 0x01 0x028 6 1345390347889 --- Logical Sectors Read 0x01 0x030 6 657125281 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 20258 --- Spindle Motor Power-on Hours 0x03 0x010 4 20258 --- Head Flying Hours 0x03 0x018 4 623 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 379 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 532 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 50 --- Current Temperature 0x05 0x010 1 50 N-- Average Short Term Temperature 0x05 0x018 1 48 N-- Average Long Term Temperature 0x05 0x020 1 65 --- Highest Temperature 0x05 0x028 1 16 --- Lowest Temperature 0x05 0x030 1 61 N-- Highest Average Short Term Temperature 0x05 0x038 1 0 N-- Lowest Average Short Term Temperature 0x05 0x040 1 53 N-- Highest Average Long Term Temperature 0x05 0x048 1 0 N-- Lowest Average Long Term Temperature 0x05 0x050 4 2140 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 1570 --- Number of Hardware Resets 0x06 0x010 4 646 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sde,megaraid_disk_05 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-62-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Ultrastar A7K2000 Device Model: Hitachi HUA722020ALA330 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: JKAOA3PA User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Jul 20 10:57:10 2025 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (22918) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 382) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 131 131 054 - 107 3 Spin_Up_Time POS--- 162 162 024 - 474 (Average 416) 4 Start_Stop_Count -O--C- 100 100 000 - 260 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 119 119 020 - 36 9 Power_On_Hours -O--C- 087 087 000 - 95961 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 260 192 Power-Off_Retract_Count -O--CK 100 100 000 - 373 193 Load_Cycle_Count -O--C- 100 100 000 - 373 194 Temperature_Celsius -O---- 122 122 000 - 49 (Min/Max 17/65) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 0 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 49 Celsius Power Cycle Min/Max Temperature: 24/55 Celsius Lifetime Min/Max Temperature: 17/65 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 260 --- Lifetime Power-On Resets 0x01 0x010 4 95961 --- Power-on Hours 0x01 0x018 6 295147832581 --- Logical Sectors Written 0x01 0x020 6 4672477571 --- Number of Write Commands 0x01 0x028 6 2013144340708 --- Logical Sectors Read 0x01 0x030 6 3269915398 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 95940 --- Spindle Motor Power-on Hours 0x03 0x010 4 95940 --- Head Flying Hours 0x03 0x018 4 373 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 12267 --- Read Recovery Attempts 0x03 0x030 4 2 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 83 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 49 --- Current Temperature 0x05 0x010 1 48 N-- Average Short Term Temperature 0x05 0x018 1 47 N-- Average Long Term Temperature 0x05 0x020 1 65 --- Highest Temperature 0x05 0x028 1 17 --- Lowest Temperature 0x05 0x030 1 61 N-- Highest Average Short Term Temperature 0x05 0x038 1 0 N-- Lowest Average Short Term Temperature 0x05 0x040 1 52 N-- Highest Average Long Term Temperature 0x05 0x048 1 0 N-- Lowest Average Long Term Temperature 0x05 0x050 4 3440 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 935 --- Number of Hardware Resets 0x06 0x010 4 423 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sde,megaraid_disk_06 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-62-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Ultrastar 7K3000 Device Model: Hitachi HUA723020ALA640 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: MK7OAA50 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jul 20 10:57:12 2025 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (20448) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 341) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 134 134 054 - 88 3 Spin_Up_Time POS--- 157 157 024 - 429 (Average 364) 4 Start_Stop_Count -O--C- 100 100 000 - 229 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 123 123 020 - 31 9 Power_On_Hours -O--C- 087 087 000 - 95968 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 229 192 Power-Off_Retract_Count -O--CK 100 100 000 - 557 193 Load_Cycle_Count -O--C- 100 100 000 - 557 194 Temperature_Celsius -O---- 130 130 000 - 46 (Min/Max 16/62) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 46 Celsius Power Cycle Min/Max Temperature: 25/54 Celsius Lifetime Min/Max Temperature: 16/62 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 229 --- Lifetime Power-On Resets 0x01 0x010 4 95968 --- Power-on Hours 0x01 0x018 6 307449468552 --- Logical Sectors Written 0x01 0x020 6 4923608181 --- Number of Write Commands 0x01 0x028 6 796915205440 --- Logical Sectors Read 0x01 0x030 6 3235783897 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 95952 --- Spindle Motor Power-on Hours 0x03 0x010 4 95952 --- Head Flying Hours 0x03 0x018 4 557 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 52 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 46 --- Current Temperature 0x05 0x010 1 45 N-- Average Short Term Temperature 0x05 0x018 1 44 N-- Average Long Term Temperature 0x05 0x020 1 62 --- Highest Temperature 0x05 0x028 1 16 --- Lowest Temperature 0x05 0x030 1 58 N-- Highest Average Short Term Temperature 0x05 0x038 1 21 N-- Lowest Average Short Term Temperature 0x05 0x040 1 49 N-- Highest Average Long Term Temperature 0x05 0x048 1 22 N-- Lowest Average Long Term Temperature 0x05 0x050 4 330 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 860 --- Number of Hardware Resets 0x06 0x010 4 352 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sde,megaraid_disk_07 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-62-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Ultrastar 7K3000 Device Model: Hitachi HUA723020ALA640 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: MK7OAA50 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jul 20 10:57:13 2025 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (20780) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 347) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 133 133 054 - 91 3 Spin_Up_Time POS--- 156 156 024 - 432 (Average 367) 4 Start_Stop_Count -O--C- 100 100 000 - 231 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 123 123 020 - 31 9 Power_On_Hours -O--C- 087 087 000 - 95969 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 231 192 Power-Off_Retract_Count -O--CK 100 100 000 - 599 193 Load_Cycle_Count -O--C- 100 100 000 - 599 194 Temperature_Celsius -O---- 133 133 000 - 45 (Min/Max 17/66) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 45 Celsius Power Cycle Min/Max Temperature: 25/52 Celsius Lifetime Min/Max Temperature: 17/66 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 231 --- Lifetime Power-On Resets 0x01 0x010 4 95969 --- Power-on Hours 0x01 0x018 6 296513419823 --- Logical Sectors Written 0x01 0x020 6 4856686232 --- Number of Write Commands 0x01 0x028 6 790646790151 --- Logical Sectors Read 0x01 0x030 6 3125685832 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 95953 --- Spindle Motor Power-on Hours 0x03 0x010 4 95953 --- Head Flying Hours 0x03 0x018 4 599 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 4 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 45 --- Current Temperature 0x05 0x010 1 43 N-- Average Short Term Temperature 0x05 0x018 1 43 N-- Average Long Term Temperature 0x05 0x020 1 66 --- Highest Temperature 0x05 0x028 1 17 --- Lowest Temperature 0x05 0x030 1 62 N-- Highest Average Short Term Temperature 0x05 0x038 1 20 N-- Lowest Average Short Term Temperature 0x05 0x040 1 50 N-- Highest Average Long Term Temperature 0x05 0x048 1 20 N-- Lowest Average Long Term Temperature 0x05 0x050 4 3260 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 724 --- Number of Hardware Resets 0x06 0x010 4 203 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS