/dev/sda,megaraid_disk_15 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-85-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: IBM-D050 Product: ST4000NM0023 Revision: BC5P Compliance: SPC-4 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c5008503c61b Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Thu Oct 2 20:15:20 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 39 C Drive Trip Temperature: 65 C Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 3580452480 0 0 3580452480 0 892595.737 0 write: 0 0 0 0 0 235272.789 0 verify: 1222934616 0 0 1222934616 0 610705.814 0 Non-medium error count: 25732629 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background long Completed - 58093 - [- - -] # 2 Background short Aborted (by user command) - 51262 - [- - -] # 3 Background short Completed - 51262 - [- - -] # 4 Background short Completed - 50796 - [- - -] # 5 Background short Completed - 50642 - [- - -] # 6 Background long Completed - 49370 - [- - -] # 7 Background short Completed - 48780 - [- - -] # 8 Background short Completed - 48773 - [- - -] # 9 Background short Completed - 0 - [- - -] Long (extended) Self-test duration: 32700 seconds [9.1 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 77534:24 [4652064 minutes] Number of background scans performed: 1114, scan progress: 75.31% Number of background medium scans performed: 1114 Device does not support General statistics and performance logging Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5008503c619 attached SAS address = 0x500605b0039be381 attached phy identifier = 1 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 41 Phy reset problem count = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5008503c61a attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_16 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-85-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST4000NM0023 Revision: GS15 Compliance: SPC-4 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500845bfe6f Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Thu Oct 2 20:15:21 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 37 C Drive Trip Temperature: 60 C Manufactured in week 40 of year 2015 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 1756 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 15289 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 1914546184 Blocks received from initiator = 1765597639 Blocks read from cache and sent to initiator = 1722649452 Number of read and write commands whose size <= segment size = 173107624 Number of read and write commands whose size > segment size = 721964 Vendor (Seagate/Hitachi) factory information number of hours powered up = 52995.60 number of minutes until next internal SMART test = 55 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 2252019011 1 0 2252019012 1 450832.760 0 write: 0 0 0 0 0 120481.539 0 verify: 280394956 0 0 280394956 0 654057.162 0 Non-medium error count: 10221023 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background long Completed 64 33555 - [- - -] # 2 Background short Aborted (by user command) 64 26718 - [- - -] # 3 Default Completed 64 26504 - [- - -] # 4 Background long Completed 64 26500 - [- - -] # 5 Default Completed 64 26492 - [- - -] # 6 Background short Completed 64 20633 - [- - -] # 7 Background short Completed 64 20557 - [- - -] # 8 Background short Completed 64 20534 - [- - -] # 9 Background short Completed 64 20532 - [- - -] #10 Background short Completed 64 3 - [- - -] #11 Reserved(7) Completed 64 3 - [- - -] Long (extended) Self-test duration: 32700 seconds [9.1 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 52995:36 [3179736 minutes] Number of background scans performed: 801, scan progress: 68.17% Number of background medium scans performed: 801 Device does not support General statistics and performance logging Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: power on reason: power on negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500845bfe6d attached SAS address = 0x500605b0039be380 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 27 Phy reset problem count = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500845bfe6e attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_17 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-85-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST4000NM0023 Revision: E007 Compliance: SPC-4 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c50057286e6f Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Thu Oct 2 20:15:22 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 37 C Drive Trip Temperature: 60 C Manufactured in week 33 of year 2013 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 706 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 5681 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 2637692426 Blocks received from initiator = 147596611 Blocks read from cache and sent to initiator = 68563923 Number of read and write commands whose size <= segment size = 725711 Number of read and write commands whose size > segment size = 4763 Vendor (Seagate/Hitachi) factory information number of hours powered up = 56071.35 number of minutes until next internal SMART test = 54 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 326713763 0 0 326713763 0 7947.568 0 write: 0 0 0 0 0 2386.188 0 verify: 975 0 0 975 0 0.000 0 Non-medium error count: 37769 [GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on'] SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background long Completed - 36632 - [- - -] # 2 Background short Aborted (by user command) - 29802 - [- - -] # 3 Background short Completed - 29336 - [- - -] # 4 Background short Completed - 29182 - [- - -] # 5 Background long Completed - 27910 - [- - -] # 6 Background short Completed - 27358 - [- - -] # 7 Background short Completed - 27350 - [- - -] # 8 Background long Completed - 26858 - [- - -] # 9 Background long Aborted (device reset ?) - 26445 - [- - -] #10 Background long Completed - 24938 - [- - -] #11 Background short Completed - 24799 - [- - -] Long (extended) Self-test duration: 32700 seconds [9.1 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 56071:21 [3364281 minutes] Number of background scans performed: 844, scan progress: 69.43% Number of background medium scans performed: 844 Device does not support General statistics and performance logging Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c50057286e6d attached SAS address = 0x500605b0039be384 attached phy identifier = 4 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c50057286e6e attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_18 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-85-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: IBM-D050 Product: ST4000NM0023 Revision: BC5P Compliance: SPC-4 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c5008503c0f7 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Thu Oct 2 20:15:23 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 39 C Drive Trip Temperature: 65 C Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 346917344 0 0 346917344 0 898320.062 0 write: 0 0 0 0 0 220907.087 0 verify: 1295605512 0 0 1295605512 0 627670.609 0 Non-medium error count: 32523874 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background long Completed - 57641 - [- - -] # 2 Background short Aborted (by user command) - 50810 - [- - -] # 3 Background short Completed - 50344 - [- - -] # 4 Background short Completed - 50190 - [- - -] # 5 Background long Completed - 48919 - [- - -] # 6 Background short Completed - 48329 - [- - -] # 7 Background short Completed - 48321 - [- - -] # 8 Background short Completed - 0 - [- - -] Long (extended) Self-test duration: 32700 seconds [9.1 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 77083:47 [4625027 minutes] Number of background scans performed: 1087, scan progress: 72.59% Number of background medium scans performed: 1087 Device does not support General statistics and performance logging Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5008503c0f5 attached SAS address = 0x500605b0039be385 attached phy identifier = 5 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 35 Phy reset problem count = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5008503c0f6 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_19 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-85-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST4000NM0023 Revision: E007 Compliance: SPC-4 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c5007767927b Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Thu Oct 2 20:15:23 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 39 C Drive Trip Temperature: 60 C Manufactured in week 34 of year 2014 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 758 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 5957 Elements in grown defect list: 1 Vendor (Seagate Cache) information Blocks sent to initiator = 3478354 Blocks received from initiator = 1665282667 Blocks read from cache and sent to initiator = 121233136 Number of read and write commands whose size <= segment size = 1098604 Number of read and write commands whose size > segment size = 2895 Vendor (Seagate/Hitachi) factory information number of hours powered up = 43478.02 number of minutes until next internal SMART test = 54 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 3985593142 0 0 3985593142 0 15394.944 0 write: 0 0 0 0 0 995.472 0 verify: 605 0 0 605 0 0.000 0 Non-medium error count: 60033 [GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on'] SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background long Completed - 24041 - [- - -] # 2 Background long Completed - 17231 - [- - -] # 3 Background short Aborted (by user command) - 17210 - [- - -] # 4 Background short Completed - 16744 - [- - -] # 5 Background short Completed - 16590 - [- - -] # 6 Background long Completed - 15318 - [- - -] # 7 Background short Completed - 14728 - [- - -] # 8 Background short Completed - 14720 - [- - -] # 9 Background long Completed - 14227 - [- - -] #10 Background long Aborted (device reset ?) - 13815 - [- - -] #11 Background long Completed - 12307 - [- - -] #12 Background short Completed - 12169 - [- - -] #13 Background short Completed - 12156 - [- - -] Long (extended) Self-test duration: 32700 seconds [9.1 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 43478:01 [2608681 minutes] Number of background scans performed: 671, scan progress: 68.26% Number of background medium scans performed: 671 # when lba(hex) [sk,asc,ascq] reassign_status 1 17159:04 00000001d16735d2 [1,18,1] Successfully reassigned Device does not support General statistics and performance logging Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c50077679279 attached SAS address = 0x500605b0039be386 attached phy identifier = 6 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 1 Phy reset problem count = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5007767927a attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_20 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-85-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST4000NM0023 Revision: GS15 Compliance: SPC-4 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c5008422869b Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Thu Oct 2 20:15:24 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 36 C Drive Trip Temperature: 60 C Manufactured in week 34 of year 2015 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 1775 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 16106 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 983898699 Blocks received from initiator = 3533290194 Blocks read from cache and sent to initiator = 3386638440 Number of read and write commands whose size <= segment size = 1294501033 Number of read and write commands whose size > segment size = 792722 Vendor (Seagate/Hitachi) factory information number of hours powered up = 71982.92 number of minutes until next internal SMART test = 55 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 1553680582 13 0 1553680595 13 645749.209 0 write: 0 0 1 1 1 240247.592 0 verify: 113305613 0 0 113305613 0 669770.454 0 Non-medium error count: 10548076 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background long Completed 64 52539 - [- - -] # 2 Background short Aborted (by user command) 64 45704 - [- - -] # 3 Background long Completed 64 45511 - [- - -] # 4 Default Completed 64 45503 - [- - -] # 5 Background short Completed 64 45503 - [- - -] # 6 Background short Completed 64 39644 - [- - -] # 7 Background short Completed 64 39568 - [- - -] # 8 Background short Completed 64 20271 - [- - -] # 9 Background short Completed 64 3 - [- - -] #10 Reserved(7) Completed 64 3 - [- - -] Long (extended) Self-test duration: 32700 seconds [9.1 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 71982:55 [4318975 minutes] Number of background scans performed: 1068, scan progress: 73.60% Number of background medium scans performed: 1068 Device does not support General statistics and performance logging Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c50084228699 attached SAS address = 0x500605b0039be387 attached phy identifier = 7 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 27 Phy reset problem count = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5008422869a attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0