/dev/sda,megaraid_disk_00 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.4.0-132-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST8000NM014A Revision: CSL9 Compliance: SPC-5 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500d1aeb10f Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Tue Feb 14 05:02:25 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 39 C Drive Trip Temperature: 60 C Manufactured in week 13 of year 2020 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 135 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 864 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 3704349216 Blocks received from initiator = 2088206808 Blocks read from cache and sent to initiator = 3848887242 Number of read and write commands whose size <= segment size = 340241135 Number of read and write commands whose size > segment size = 3110758 Vendor (Seagate/Hitachi) factory information number of hours powered up = 17806.17 number of minutes until next internal SMART test = 26 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 2 0 2 2 35854.395 0 write: 0 0 0 0 0 42178.448 0 verify: 0 6 0 6 6 861658.447 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Reserved(7) Completed 80 3 - [- - -] # 2 Background short Completed - 1 - [- - -] Long (extended) Self-test duration: 45480 seconds [758.0 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 17806:11 [1068371 minutes] Number of background scans performed: 130, scan progress: 0.00% Number of background medium scans performed: 130 # when lba(hex) [sk,asc,ascq] reassign_status 1 631:56 00000000033cfff8 [1,17,1] Recovered via rewrite in-place 2 3064:49 00000000033cfff8 [1,18,4] Recovered via rewrite in-place 3 4886:05 00000000033cfff8 [1,18,4] Recovered via rewrite in-place 4 5431:31 00000000033cfff8 [1,18,4] Recovered via rewrite in-place 5 7585:50 0000000147499b80 [1,18,4] Recovered via rewrite in-place Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 6 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500d1aeb10d attached SAS address = 0x570b5e80dd95a501 attached phy identifier = 4 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 14 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 14 Phy reset problem count: 0 relative target port id = 2 generation code = 6 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500d1aeb10e attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sda,megaraid_disk_01 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.4.0-132-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST8000NM014A Revision: CSL9 Compliance: SPC-5 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500d1aeb6c3 Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Tue Feb 14 05:02:26 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 39 C Drive Trip Temperature: 60 C Manufactured in week 13 of year 2020 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 135 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 863 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 4116757744 Blocks received from initiator = 2900981648 Blocks read from cache and sent to initiator = 4031499890 Number of read and write commands whose size <= segment size = 337386598 Number of read and write commands whose size > segment size = 3180476 Vendor (Seagate/Hitachi) factory information number of hours powered up = 17806.45 number of minutes until next internal SMART test = 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 7 0 7 7 36104.203 0 write: 0 0 0 0 0 42595.076 0 verify: 0 3 0 3 3 861623.091 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Reserved(7) Completed 80 3 - [- - -] # 2 Background short Completed - 1 - [- - -] Long (extended) Self-test duration: 45480 seconds [758.0 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 17806:27 [1068387 minutes] Number of background scans performed: 130, scan progress: 0.00% Number of background medium scans performed: 130 # when lba(hex) [sk,asc,ascq] reassign_status 1 544:01 00000000028ccdd0 [1,18,4] Recovered via rewrite in-place 2 3134:35 000000007c287e40 [1,18,4] Recovered via rewrite in-place 3 6291:16 00000000949bf7f0 [1,18,4] Recovered via rewrite in-place 4 7276:21 000000013f941f88 [1,18,4] Recovered via rewrite in-place Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: power on reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500d1aeb6c1 attached SAS address = 0x570b5e80dd95a500 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 6 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 6 Phy reset problem count: 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500d1aeb6c2 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sda,megaraid_disk_02 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.4.0-132-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST8000NM014A Revision: CSL9 Compliance: SPC-5 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500ca5aa833 Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Tue Feb 14 05:02:27 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 36 C Drive Trip Temperature: 60 C Manufactured in week 22 of year 2020 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 193 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 923 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 171243952 Blocks received from initiator = 2736702912 Blocks read from cache and sent to initiator = 4167377570 Number of read and write commands whose size <= segment size = 336305968 Number of read and write commands whose size > segment size = 3044497 Vendor (Seagate/Hitachi) factory information number of hours powered up = 17806.57 number of minutes until next internal SMART test = 6 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 36567.286 0 write: 0 0 0 0 0 42695.112 0 verify: 0 0 0 0 0 861341.724 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Reserved(7) Completed 80 3 - [- - -] # 2 Background short Completed - 2 - [- - -] Long (extended) Self-test duration: 45480 seconds [758.0 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 17806:34 [1068394 minutes] Number of background scans performed: 130, scan progress: 0.00% Number of background medium scans performed: 130 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 6 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500ca5aa831 attached SAS address = 0x570b5e80dd95a503 attached phy identifier = 6 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization = 16 Phy reset problem = 0 Phy event descriptors: Invalid word count: 4 Running disparity error count: 4 Loss of dword synchronization count: 16 Phy reset problem count: 0 relative target port id = 2 generation code = 6 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500ca5aa832 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sda,megaraid_disk_03 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.4.0-132-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: Samsung SSD 870 EVO 2TB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: SVT01B6Q User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Feb 14 05:02:27 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 160) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 044 044 010 - 1294 9 Power_On_Hours -O--CK 097 097 000 - 14511 12 Power_Cycle_Count -O--CK 099 099 000 - 14 177 Wear_Leveling_Count PO--C- 099 099 000 - 23 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 044 044 010 - 1294 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 044 044 010 - 1294 187 Reported_Uncorrect -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 069 048 000 - 31 195 Hardware_ECC_Recovered -O-RC- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 100 100 000 - 0 235 Unknown_Attribute -O--C- 099 099 000 - 6 241 Total_LBAs_Written -O--CK 099 099 000 - 74782159512 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 5542 - # 2 Short offline Completed without error 00% 5518 - # 3 Short offline Completed without error 00% 5494 - # 4 Short offline Completed without error 00% 5470 - # 5 Short offline Completed without error 00% 5446 - # 6 Short offline Completed without error 00% 5422 - # 7 Short offline Completed without error 00% 5398 - # 8 Short offline Completed without error 00% 5374 - # 9 Short offline Completed without error 00% 5350 - #10 Short offline Completed without error 00% 5326 - #11 Short offline Completed without error 00% 5302 - #12 Extended offline Completed without error 00% 5278 - #13 Short offline Completed without error 00% 5254 - #14 Short offline Completed without error 00% 5230 - #15 Short offline Completed without error 00% 5206 - #16 Short offline Completed without error 00% 5182 - #17 Short offline Completed without error 00% 5158 - #18 Short offline Completed without error 00% 5134 - #19 Short offline Completed without error 00% 5110 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 256 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 27/42 Celsius Lifetime Min/Max Temperature: 23/51 Celsius Specified Max Operating Temperature: 70 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 14 --- Lifetime Power-On Resets 0x01 0x010 4 14511 --- Power-on Hours 0x01 0x018 6 74782159512 --- Logical Sectors Written 0x01 0x020 6 178323960 --- Number of Write Commands 0x01 0x028 6 10689927871 --- Logical Sectors Read 0x01 0x030 6 29672907 --- Number of Read Commands 0x01 0x038 6 607000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 1 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 31 --- Current Temperature 0x05 0x020 1 51 --- Highest Temperature 0x05 0x028 1 23 --- Lowest Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 41 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 1 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 7 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 7 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sda,megaraid_disk_04 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.4.0-132-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST8000NM014A Revision: CSL9 Compliance: SPC-5 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500ca5aae6f Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Tue Feb 14 05:02:27 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 35 C Drive Trip Temperature: 60 C Manufactured in week 22 of year 2020 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 205 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 584 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 1880494664 Blocks received from initiator = 3678466608 Blocks read from cache and sent to initiator = 3643518376 Number of read and write commands whose size <= segment size = 179128402 Number of read and write commands whose size > segment size = 671474 Vendor (Seagate/Hitachi) factory information number of hours powered up = 10434.32 number of minutes until next internal SMART test = 3 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 76064.496 0 write: 0 0 2 2 2 24581.089 0 verify: 0 0 0 0 0 398390.556 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed - 8123 - [- - -] # 2 Background short Completed - 8099 - [- - -] # 3 Background short Completed - 8075 - [- - -] # 4 Background short Completed - 8051 - [- - -] # 5 Background short Completed - 8027 - [- - -] # 6 Background short Completed - 8003 - [- - -] # 7 Background short Completed - 7979 - [- - -] # 8 Background short Completed - 7955 - [- - -] # 9 Background short Completed - 7931 - [- - -] #10 Background short Completed - 7907 - [- - -] #11 Background long Completed - 7902 - [- - -] #12 Background short Completed - 7835 - [- - -] #13 Background short Completed - 7811 - [- - -] #14 Background short Completed - 7787 - [- - -] #15 Background short Completed - 7763 - [- - -] #16 Background short Completed - 7739 - [- - -] #17 Background short Completed - 7715 - [- - -] #18 Background short Completed - 7691 - [- - -] #19 Background short Completed - 7667 - [- - -] #20 Background short Completed - 7643 - [- - -] Long (extended) Self-test duration: 45480 seconds [758.0 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 10434:19 [626059 minutes] Number of background scans performed: 71, scan progress: 0.00% Number of background medium scans performed: 71 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 6 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500ca5aae6d attached SAS address = 0x570b5e80dd95a502 attached phy identifier = 5 Invalid DWORD count = 8 Running disparity error count = 7 Loss of DWORD synchronization = 16 Phy reset problem = 0 Phy event descriptors: Invalid word count: 8 Running disparity error count: 7 Loss of dword synchronization count: 16 Phy reset problem count: 0 relative target port id = 2 generation code = 6 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500ca5aae6e attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sdb,megaraid_disk_00 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.4.0-132-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST8000NM014A Revision: CSL9 Compliance: SPC-5 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500d1aeb10f Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Tue Feb 14 05:02:29 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 39 C Drive Trip Temperature: 60 C Manufactured in week 13 of year 2020 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 135 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 864 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 3704349216 Blocks received from initiator = 2088207000 Blocks read from cache and sent to initiator = 3848887242 Number of read and write commands whose size <= segment size = 340241137 Number of read and write commands whose size > segment size = 3110758 Vendor (Seagate/Hitachi) factory information number of hours powered up = 17806.18 number of minutes until next internal SMART test = 26 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 2 0 2 2 35854.395 0 write: 0 0 0 0 0 42178.448 0 verify: 0 6 0 6 6 861658.447 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Reserved(7) Completed 80 3 - [- - -] # 2 Background short Completed - 1 - [- - -] Long (extended) Self-test duration: 45480 seconds [758.0 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 17806:11 [1068371 minutes] Number of background scans performed: 130, scan progress: 0.00% Number of background medium scans performed: 130 # when lba(hex) [sk,asc,ascq] reassign_status 1 631:56 00000000033cfff8 [1,17,1] Recovered via rewrite in-place 2 3064:49 00000000033cfff8 [1,18,4] Recovered via rewrite in-place 3 4886:05 00000000033cfff8 [1,18,4] Recovered via rewrite in-place 4 5431:31 00000000033cfff8 [1,18,4] Recovered via rewrite in-place 5 7585:50 0000000147499b80 [1,18,4] Recovered via rewrite in-place Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 6 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500d1aeb10d attached SAS address = 0x570b5e80dd95a501 attached phy identifier = 4 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 14 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 14 Phy reset problem count: 0 relative target port id = 2 generation code = 6 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500d1aeb10e attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sdb,megaraid_disk_01 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.4.0-132-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST8000NM014A Revision: CSL9 Compliance: SPC-5 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500d1aeb6c3 Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Tue Feb 14 05:02:30 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 39 C Drive Trip Temperature: 60 C Manufactured in week 13 of year 2020 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 135 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 863 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 4116757744 Blocks received from initiator = 2900981648 Blocks read from cache and sent to initiator = 4031499890 Number of read and write commands whose size <= segment size = 337386598 Number of read and write commands whose size > segment size = 3180476 Vendor (Seagate/Hitachi) factory information number of hours powered up = 17806.45 number of minutes until next internal SMART test = 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 7 0 7 7 36104.203 0 write: 0 0 0 0 0 42595.076 0 verify: 0 3 0 3 3 861623.091 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Reserved(7) Completed 80 3 - [- - -] # 2 Background short Completed - 1 - [- - -] Long (extended) Self-test duration: 45480 seconds [758.0 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 17806:27 [1068387 minutes] Number of background scans performed: 130, scan progress: 0.00% Number of background medium scans performed: 130 # when lba(hex) [sk,asc,ascq] reassign_status 1 544:01 00000000028ccdd0 [1,18,4] Recovered via rewrite in-place 2 3134:35 000000007c287e40 [1,18,4] Recovered via rewrite in-place 3 6291:16 00000000949bf7f0 [1,18,4] Recovered via rewrite in-place 4 7276:21 000000013f941f88 [1,18,4] Recovered via rewrite in-place Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: power on reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500d1aeb6c1 attached SAS address = 0x570b5e80dd95a500 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 6 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 6 Phy reset problem count: 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500d1aeb6c2 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sdb,megaraid_disk_02 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.4.0-132-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST8000NM014A Revision: CSL9 Compliance: SPC-5 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500ca5aa833 Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Tue Feb 14 05:02:31 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 36 C Drive Trip Temperature: 60 C Manufactured in week 22 of year 2020 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 193 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 923 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 171243952 Blocks received from initiator = 2736702912 Blocks read from cache and sent to initiator = 4167377570 Number of read and write commands whose size <= segment size = 336305968 Number of read and write commands whose size > segment size = 3044497 Vendor (Seagate/Hitachi) factory information number of hours powered up = 17806.57 number of minutes until next internal SMART test = 6 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 36567.286 0 write: 0 0 0 0 0 42695.112 0 verify: 0 0 0 0 0 861341.724 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Reserved(7) Completed 80 3 - [- - -] # 2 Background short Completed - 2 - [- - -] Long (extended) Self-test duration: 45480 seconds [758.0 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 17806:34 [1068394 minutes] Number of background scans performed: 130, scan progress: 0.00% Number of background medium scans performed: 130 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 6 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500ca5aa831 attached SAS address = 0x570b5e80dd95a503 attached phy identifier = 6 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization = 16 Phy reset problem = 0 Phy event descriptors: Invalid word count: 4 Running disparity error count: 4 Loss of dword synchronization count: 16 Phy reset problem count: 0 relative target port id = 2 generation code = 6 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500ca5aa832 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sdb,megaraid_disk_03 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.4.0-132-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: Samsung SSD 870 EVO 2TB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: SVT01B6Q User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Feb 14 05:02:31 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 160) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 044 044 010 - 1294 9 Power_On_Hours -O--CK 097 097 000 - 14511 12 Power_Cycle_Count -O--CK 099 099 000 - 14 177 Wear_Leveling_Count PO--C- 099 099 000 - 23 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 044 044 010 - 1294 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 044 044 010 - 1294 187 Reported_Uncorrect -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 069 048 000 - 31 195 Hardware_ECC_Recovered -O-RC- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 100 100 000 - 0 235 Unknown_Attribute -O--C- 099 099 000 - 6 241 Total_LBAs_Written -O--CK 099 099 000 - 74782159512 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 5542 - # 2 Short offline Completed without error 00% 5518 - # 3 Short offline Completed without error 00% 5494 - # 4 Short offline Completed without error 00% 5470 - # 5 Short offline Completed without error 00% 5446 - # 6 Short offline Completed without error 00% 5422 - # 7 Short offline Completed without error 00% 5398 - # 8 Short offline Completed without error 00% 5374 - # 9 Short offline Completed without error 00% 5350 - #10 Short offline Completed without error 00% 5326 - #11 Short offline Completed without error 00% 5302 - #12 Extended offline Completed without error 00% 5278 - #13 Short offline Completed without error 00% 5254 - #14 Short offline Completed without error 00% 5230 - #15 Short offline Completed without error 00% 5206 - #16 Short offline Completed without error 00% 5182 - #17 Short offline Completed without error 00% 5158 - #18 Short offline Completed without error 00% 5134 - #19 Short offline Completed without error 00% 5110 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 256 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 27/42 Celsius Lifetime Min/Max Temperature: 23/51 Celsius Specified Max Operating Temperature: 70 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 14 --- Lifetime Power-On Resets 0x01 0x010 4 14511 --- Power-on Hours 0x01 0x018 6 74782159512 --- Logical Sectors Written 0x01 0x020 6 178323960 --- Number of Write Commands 0x01 0x028 6 10689927871 --- Logical Sectors Read 0x01 0x030 6 29672907 --- Number of Read Commands 0x01 0x038 6 611000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 1 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 31 --- Current Temperature 0x05 0x020 1 51 --- Highest Temperature 0x05 0x028 1 23 --- Lowest Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 41 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 1 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 7 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 7 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb,megaraid_disk_04 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.4.0-132-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST8000NM014A Revision: CSL9 Compliance: SPC-5 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500ca5aae6f Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Tue Feb 14 05:02:31 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 35 C Drive Trip Temperature: 60 C Manufactured in week 22 of year 2020 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 205 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 584 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 1880496064 Blocks received from initiator = 3678466608 Blocks read from cache and sent to initiator = 3643519032 Number of read and write commands whose size <= segment size = 179128403 Number of read and write commands whose size > segment size = 671474 Vendor (Seagate/Hitachi) factory information number of hours powered up = 10434.32 number of minutes until next internal SMART test = 3 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 76064.496 0 write: 0 0 2 2 2 24581.089 0 verify: 0 0 0 0 0 398390.556 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed - 8123 - [- - -] # 2 Background short Completed - 8099 - [- - -] # 3 Background short Completed - 8075 - [- - -] # 4 Background short Completed - 8051 - [- - -] # 5 Background short Completed - 8027 - [- - -] # 6 Background short Completed - 8003 - [- - -] # 7 Background short Completed - 7979 - [- - -] # 8 Background short Completed - 7955 - [- - -] # 9 Background short Completed - 7931 - [- - -] #10 Background short Completed - 7907 - [- - -] #11 Background long Completed - 7902 - [- - -] #12 Background short Completed - 7835 - [- - -] #13 Background short Completed - 7811 - [- - -] #14 Background short Completed - 7787 - [- - -] #15 Background short Completed - 7763 - [- - -] #16 Background short Completed - 7739 - [- - -] #17 Background short Completed - 7715 - [- - -] #18 Background short Completed - 7691 - [- - -] #19 Background short Completed - 7667 - [- - -] #20 Background short Completed - 7643 - [- - -] Long (extended) Self-test duration: 45480 seconds [758.0 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 10434:19 [626059 minutes] Number of background scans performed: 71, scan progress: 0.00% Number of background medium scans performed: 71 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 6 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500ca5aae6d attached SAS address = 0x570b5e80dd95a502 attached phy identifier = 5 Invalid DWORD count = 8 Running disparity error count = 7 Loss of DWORD synchronization = 16 Phy reset problem = 0 Phy event descriptors: Invalid word count: 8 Running disparity error count: 7 Loss of dword synchronization count: 16 Phy reset problem count: 0 relative target port id = 2 generation code = 6 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500ca5aae6e attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sdc,megaraid_disk_00 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.4.0-132-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST8000NM014A Revision: CSL9 Compliance: SPC-5 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500d1aeb10f Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Tue Feb 14 05:02:33 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 39 C Drive Trip Temperature: 60 C Manufactured in week 13 of year 2020 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 135 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 864 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 3704350656 Blocks received from initiator = 2088208064 Blocks read from cache and sent to initiator = 3848887258 Number of read and write commands whose size <= segment size = 340241162 Number of read and write commands whose size > segment size = 3110758 Vendor (Seagate/Hitachi) factory information number of hours powered up = 17806.18 number of minutes until next internal SMART test = 26 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 2 0 2 2 35854.396 0 write: 0 0 0 0 0 42178.448 0 verify: 0 6 0 6 6 861658.447 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Reserved(7) Completed 80 3 - [- - -] # 2 Background short Completed - 1 - [- - -] Long (extended) Self-test duration: 45480 seconds [758.0 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 17806:11 [1068371 minutes] Number of background scans performed: 130, scan progress: 0.00% Number of background medium scans performed: 130 # when lba(hex) [sk,asc,ascq] reassign_status 1 631:56 00000000033cfff8 [1,17,1] Recovered via rewrite in-place 2 3064:49 00000000033cfff8 [1,18,4] Recovered via rewrite in-place 3 4886:05 00000000033cfff8 [1,18,4] Recovered via rewrite in-place 4 5431:31 00000000033cfff8 [1,18,4] Recovered via rewrite in-place 5 7585:50 0000000147499b80 [1,18,4] Recovered via rewrite in-place Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 6 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500d1aeb10d attached SAS address = 0x570b5e80dd95a501 attached phy identifier = 4 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 14 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 14 Phy reset problem count: 0 relative target port id = 2 generation code = 6 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500d1aeb10e attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sdc,megaraid_disk_01 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.4.0-132-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST8000NM014A Revision: CSL9 Compliance: SPC-5 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500d1aeb6c3 Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Tue Feb 14 05:02:34 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 39 C Drive Trip Temperature: 60 C Manufactured in week 13 of year 2020 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 135 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 863 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 4116757800 Blocks received from initiator = 2900983392 Blocks read from cache and sent to initiator = 4031499898 Number of read and write commands whose size <= segment size = 337386618 Number of read and write commands whose size > segment size = 3180476 Vendor (Seagate/Hitachi) factory information number of hours powered up = 17806.45 number of minutes until next internal SMART test = 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 7 0 7 7 36104.203 0 write: 0 0 0 0 0 42595.077 0 verify: 0 3 0 3 3 861623.091 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Reserved(7) Completed 80 3 - [- - -] # 2 Background short Completed - 1 - [- - -] Long (extended) Self-test duration: 45480 seconds [758.0 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 17806:27 [1068387 minutes] Number of background scans performed: 130, scan progress: 0.00% Number of background medium scans performed: 130 # when lba(hex) [sk,asc,ascq] reassign_status 1 544:01 00000000028ccdd0 [1,18,4] Recovered via rewrite in-place 2 3134:35 000000007c287e40 [1,18,4] Recovered via rewrite in-place 3 6291:16 00000000949bf7f0 [1,18,4] Recovered via rewrite in-place 4 7276:21 000000013f941f88 [1,18,4] Recovered via rewrite in-place Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: power on reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500d1aeb6c1 attached SAS address = 0x570b5e80dd95a500 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 6 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 6 Phy reset problem count: 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500d1aeb6c2 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sdc,megaraid_disk_02 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.4.0-132-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST8000NM014A Revision: CSL9 Compliance: SPC-5 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500ca5aa833 Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Tue Feb 14 05:02:35 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 36 C Drive Trip Temperature: 60 C Manufactured in week 22 of year 2020 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 193 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 923 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 171250680 Blocks received from initiator = 2736703568 Blocks read from cache and sent to initiator = 4167377618 Number of read and write commands whose size <= segment size = 336305988 Number of read and write commands whose size > segment size = 3044497 Vendor (Seagate/Hitachi) factory information number of hours powered up = 17806.57 number of minutes until next internal SMART test = 6 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 36567.290 0 write: 0 0 0 0 0 42695.112 0 verify: 0 0 0 0 0 861341.724 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Reserved(7) Completed 80 3 - [- - -] # 2 Background short Completed - 2 - [- - -] Long (extended) Self-test duration: 45480 seconds [758.0 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 17806:34 [1068394 minutes] Number of background scans performed: 130, scan progress: 0.00% Number of background medium scans performed: 130 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 6 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500ca5aa831 attached SAS address = 0x570b5e80dd95a503 attached phy identifier = 6 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization = 16 Phy reset problem = 0 Phy event descriptors: Invalid word count: 4 Running disparity error count: 4 Loss of dword synchronization count: 16 Phy reset problem count: 0 relative target port id = 2 generation code = 6 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500ca5aa832 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sdc,megaraid_disk_03 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.4.0-132-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: Samsung SSD 870 EVO 2TB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: SVT01B6Q User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Feb 14 05:02:36 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 160) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 044 044 010 - 1294 9 Power_On_Hours -O--CK 097 097 000 - 14511 12 Power_Cycle_Count -O--CK 099 099 000 - 14 177 Wear_Leveling_Count PO--C- 099 099 000 - 23 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 044 044 010 - 1294 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 044 044 010 - 1294 187 Reported_Uncorrect -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 069 048 000 - 31 195 Hardware_ECC_Recovered -O-RC- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 100 100 000 - 0 235 Unknown_Attribute -O--C- 099 099 000 - 6 241 Total_LBAs_Written -O--CK 099 099 000 - 74782159512 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 5542 - # 2 Short offline Completed without error 00% 5518 - # 3 Short offline Completed without error 00% 5494 - # 4 Short offline Completed without error 00% 5470 - # 5 Short offline Completed without error 00% 5446 - # 6 Short offline Completed without error 00% 5422 - # 7 Short offline Completed without error 00% 5398 - # 8 Short offline Completed without error 00% 5374 - # 9 Short offline Completed without error 00% 5350 - #10 Short offline Completed without error 00% 5326 - #11 Short offline Completed without error 00% 5302 - #12 Extended offline Completed without error 00% 5278 - #13 Short offline Completed without error 00% 5254 - #14 Short offline Completed without error 00% 5230 - #15 Short offline Completed without error 00% 5206 - #16 Short offline Completed without error 00% 5182 - #17 Short offline Completed without error 00% 5158 - #18 Short offline Completed without error 00% 5134 - #19 Short offline Completed without error 00% 5110 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 256 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 27/42 Celsius Lifetime Min/Max Temperature: 23/51 Celsius Specified Max Operating Temperature: 70 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 14 --- Lifetime Power-On Resets 0x01 0x010 4 14511 --- Power-on Hours 0x01 0x018 6 74782159512 --- Logical Sectors Written 0x01 0x020 6 178323960 --- Number of Write Commands 0x01 0x028 6 10689927871 --- Logical Sectors Read 0x01 0x030 6 29672907 --- Number of Read Commands 0x01 0x038 6 615000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 1 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 31 --- Current Temperature 0x05 0x020 1 51 --- Highest Temperature 0x05 0x028 1 23 --- Lowest Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 41 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 1 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 7 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 7 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdc,megaraid_disk_04 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.4.0-132-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST8000NM014A Revision: CSL9 Compliance: SPC-5 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500ca5aae6f Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Tue Feb 14 05:02:36 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 35 C Drive Trip Temperature: 60 C Manufactured in week 22 of year 2020 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 205 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 584 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 1880496064 Blocks received from initiator = 3678466608 Blocks read from cache and sent to initiator = 3643521864 Number of read and write commands whose size <= segment size = 179128403 Number of read and write commands whose size > segment size = 671474 Vendor (Seagate/Hitachi) factory information number of hours powered up = 10434.32 number of minutes until next internal SMART test = 3 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 76064.496 0 write: 0 0 2 2 2 24581.089 0 verify: 0 0 0 0 0 398390.556 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed - 8123 - [- - -] # 2 Background short Completed - 8099 - [- - -] # 3 Background short Completed - 8075 - [- - -] # 4 Background short Completed - 8051 - [- - -] # 5 Background short Completed - 8027 - [- - -] # 6 Background short Completed - 8003 - [- - -] # 7 Background short Completed - 7979 - [- - -] # 8 Background short Completed - 7955 - [- - -] # 9 Background short Completed - 7931 - [- - -] #10 Background short Completed - 7907 - [- - -] #11 Background long Completed - 7902 - [- - -] #12 Background short Completed - 7835 - [- - -] #13 Background short Completed - 7811 - [- - -] #14 Background short Completed - 7787 - [- - -] #15 Background short Completed - 7763 - [- - -] #16 Background short Completed - 7739 - [- - -] #17 Background short Completed - 7715 - [- - -] #18 Background short Completed - 7691 - [- - -] #19 Background short Completed - 7667 - [- - -] #20 Background short Completed - 7643 - [- - -] Long (extended) Self-test duration: 45480 seconds [758.0 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 10434:19 [626059 minutes] Number of background scans performed: 71, scan progress: 0.00% Number of background medium scans performed: 71 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 6 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500ca5aae6d attached SAS address = 0x570b5e80dd95a502 attached phy identifier = 5 Invalid DWORD count = 8 Running disparity error count = 7 Loss of DWORD synchronization = 16 Phy reset problem = 0 Phy event descriptors: Invalid word count: 8 Running disparity error count: 7 Loss of dword synchronization count: 16 Phy reset problem count: 0 relative target port id = 2 generation code = 6 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500ca5aae6e attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0