/dev/sda,megaraid_disk_00 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-11-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: TOSHIBA Product: KPM5XVUG3T84 Revision: B01C Compliance: SPC-4 User Capacity: 3,840,755,982,336 bytes [3.84 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is resource provisioned, LBPRZ=1 Rotation Rate: Solid State Device Form Factor: 2.5 inches Logical Unit id: 0x58ce38ee211eae7d Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Fri Nov 7 13:52:27 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Percentage used endurance indicator: 8% Current temperature = 29 Lifetime maximum temperature = 51 Lifetime minimum temperature = 17 Maximum temperature since power on = 39 Minimum temperature since power on = 25 Manufactured in week 35 of year 2020 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 835976.424 0 write: 0 0 0 0 0 308152.069 0 verify: 0 0 0 0 0 730646.510 0 Non-medium error count: 80 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background long Completed - 12 - [- - -] # 2 Background short Completed - 12 - [- - -] # 3 Background long Completed - 2 - [- - -] # 4 Background short Completed - 2 - [- - -] Long (extended) Self-test duration: 300 seconds [5.0 minutes] Background scan results log Status: no scans active Accumulated power on time, hours:minutes 35656:27 [2139387 minutes] Number of background scans performed: 0, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x58ce38ee211eae7e attached SAS address = 0x5d09466029897501 attached phy identifier = 4 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization count = 1 Phy reset problem count = 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x58ce38ee211eae7f attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_01 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-11-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: TOSHIBA Product: KPM5XVUG3T84 Revision: B01C Compliance: SPC-4 User Capacity: 3,840,755,982,336 bytes [3.84 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is resource provisioned, LBPRZ=1 Rotation Rate: Solid State Device Form Factor: 2.5 inches Logical Unit id: 0x58ce38ee211eaeb9 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Fri Nov 7 13:52:27 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Percentage used endurance indicator: 8% Current temperature = 30 Lifetime maximum temperature = 51 Lifetime minimum temperature = 17 Maximum temperature since power on = 40 Minimum temperature since power on = 26 Manufactured in week 35 of year 2020 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 830829.829 0 write: 0 0 0 0 0 311992.021 0 verify: 0 0 0 0 0 730645.904 0 Non-medium error count: 80 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background long Completed - 12 - [- - -] # 2 Background short Completed - 12 - [- - -] # 3 Background long Completed - 2 - [- - -] # 4 Background short Completed - 2 - [- - -] Long (extended) Self-test duration: 300 seconds [5.0 minutes] Background scan results log Status: no scans active Accumulated power on time, hours:minutes 35656:24 [2139384 minutes] Number of background scans performed: 0, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 1 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: power on reason: power on negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x58ce38ee211eaeba attached SAS address = 0x5d09466029897500 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 relative target port id = 2 generation code = 1 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x58ce38ee211eaebb attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0